Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Journal of Solid-State Circuits

Cryo-CMOS Dual-Qubit Homodyne Reflectometer Array With Degenerate Parametric Amplification

Yujie Geng, Haichuan Lin, Bo Wang, Cheng Wang

Published Jul 30, 2024• 7 citations
Publisher

Abstract

In quantum computers, the quantum state discrimination of the physical quantum bits (Qubits) occupies ~80% of the quantum error correction (QEC) cycle. The RF reflectometry or dispersive readout determines the Qubit state by monitoring the RF reflection of the attached high-Q resonant tank. Compared to their dc counterparts, the RF reflectometers enjoy a high signal-to-noise ratio (SNR), low drifting, and fast speed. As a result, a high-fidelity, single-shot, scalable reflectometer array based on cryogenic CMOS (Cryo-CMOS) ICs is in demand for the future large-scale Qubit array ($10^{3} {\sim } 10^{6}$Qubits). However, the classic Cryo-CMOS heterodyne reflectometers, consisting of MOSFET-based LNA, mixer, and baseband blocks, suffer from high noise temperature and dc power. To address these issues, the Cryo-CMOS parametric circuitry based on varactors is explored. In this article, a dual-Qubit homodyne reflectometer array with 2 RX channels and 1 TX channel is demonstrated. In the RX, the degenerate parametric amplifier (DPA) enjoys a Q-enhanced,$\lambda _{\mathrm { RF}}/2$differential-mode (DM) resonator for the high-gain parametric amplification. The common mode (CM) RF input of DPA interacts with the DM resonator by a nonreciprocal, dynamic mode coupling (DMC). It eliminates the necessity of a circulator and the potential oscillation of DPA. The scalability challenge of the DPA’s noise temperature$T_{\mathrm { noise}}$versus the environment temperature$T_{\mathrm { env}}$is also investigated. In the TX, a current-mode logic (CML) divider with interstate locking and a vector modulator (VM) is implemented to achieve fast modulation for the spur and noise rejection. Measured at 4.2 K, the implemented 65 nm Cryo-CMOS chip presents a$4.5{\sim }7$GHz bandwidth, 52 dB peak RF gain, and 78 K noise temperature, and generates a 10 MHz TX pulse train with -22 dBm RF power and 30 dB tunability. It consumes a total dc power of 33 mW.

DOI
10.1109/jssc.2024.3430079

Related papers

A Cryo-CMOS 4.5~7GHz Dual-Qubit Homodyne Reflectometer Array with High Q Degenerate Parametric Amplifier Through Dynamic Mode Coupling

Yujie Geng, Haichuan Lin, Bo Wang +1 more

Error-corrected quantum computing does not only require large-scale (106–109) physical Qubit arrays but also relies on high-fidelity, scalable quantum-to-classic interface electronics. Quantum control and readout systems based on cryogenic CMOS integrated circuits mitigate the error of Qubit manipulation, reduce the cabling complexity, and facilitate the quantum feedback, which pave the way towards practical quantum error correction (QEC) and logic quantum gates. RF reflectometry is widely adopted for qubit states readout. Reflectometry conducts Qubit states discrimination (collapsed to “0” or “1”) by detecting the resonant frequency through RF reflection of a high-Q LC tank associated with the sensor Qubit (Fig. 1). The quantum states are encoded in either the amplitude or the phase of the reflected RF signal. Compared with its DC counterpart, the reflectometry achieves unprecedented charge sensitivity, reduces the integration time, and avoids long-term drifting. However, conventional heterodyne reflectometer schemes [1][4][5] adopt sophisticated up/down mixers, ADC, DAC, and PLL for the Qubit excitation and down-mixing, respectively. They suffer from poor TX-RX isolation, inter-modulation, and high DC power, which deteriorate the scalability and readout fidelity. To address these challenges, a highly scalable dual-Qubit homodyne reflectometer array is proposed in this paper. It drives the LC tank by a single PLL and detects the reflection by a high-gain degenerate parametric amplifier (DPA). Along with fast modulation and lock-in detection, it mitigates the interference, complex cabling, and high DC power of conventional heterodyne reflectometers.

IEEE Asian Solid-State Circuits Conference (A-SSCC)•Nov 5, 2023•2 citations

A Cryo-CMOS Parametric Frequency Divider With −189.1 dBm/Hz Output Noise Floor at 4.2 K for High-Fidelity All-Parametric Quantum Reflectometer

Yujie Geng, Haichuan Lin, Bo Wang +1 more

Main-stream quantum computers employ dispersive reflectometry for quantum-bit (Qubit) state discrimination. An all-parametric quantum reflectometer (APQR) scheme has been proposed for high-fidelity, scalable Qubit array readout in this letter. For the RF excitation of APQR, a 10.7–16.9 GHz 65-nm cryogenic CMOS (Cryo-CMOS) parametric frequency divider (PFD) is demonstrated here. It adopts a pair of parallelly connected nonlinear artificial transmission lines (NLATLs), a wideband varactor-based dynamic coupler, and a transformer-based CM filter (TCMF). Due to the minimized device self-heating without dc power consumption and the intrinsic common-mode (CM) to differential-mode (DM) isolation, the PFD presents a measured output thermal noise floor of −189.1 dBm/Hz at 4.2 K. This is only 3.3 dB higher than 4.2-K blackbody radiation. At 4.2 K, the PFD also exhibits an ultralow phase noise of −128.8 dBc/Hz at 1 MHz at 6.75 GHz, which is 2.6 dB lower than a conventional Cryo-CMOS CML divider. It presents a 44.9% relative bandwidth at 4.2 K, which is$2\times $of the prior art at 300 K.

IEEE Microwave and Wireless Technology Letters•Oct 26, 2023•5 citations

28-nm Cryo-CMOS Mixer-First Reflectometer for the FDM Readout of Transmon Qubits

Yujie Geng, Zixin Xu, Tianyu Dong +8 more

Quantum error correction (QEC) is in demand for a fault-tolerant quantum computer. Currently, the QEC cycle is bottlenecked by the quantum bit (qubit) readout. To this end, RF dispersive reflectometry with frequency division multiplexing (FDM) is preferred due to its high fidelity and scalability. However, for a low noise temperature$T_{noise}$, cryogenic low noise amplifiers (cryo-LNAs) of classic LNA-first reflectometers require high transconductance efficiency ($g_{m}^{2}/I_{d}$). These open-loop cryo-LNAs also present limited linearity under large output voltage, resulting in errors of FDM readout. In this work, a new approach, a mixer-first cryogenic CMOS (Cryo-CMOS) reflectometer, is explored for its potential advantages in noise and linearity. A passive, low-loss mixer directly down-converts the RF reflection from the qubits (5.5–8 GHz) at 4 K to IF/baseband (5–250 MHz). Then, an IF/baseband amplifier, employing a MOSFET pair of$W/L = 2{\,}\times {\,}800~\mu $m/100 nm and current density of$5~\mu $A/$\mu $m, achieves$2.8\times $higher$g_{m}^{2}/I_{d}$than Cryo-CMOS LNAs for low noise. After closed-loop amplification with high linearity, the baseband is sampled by a 500 MSPS, 12-bit time-interleaved (TI) analog-to-digital converter (ADC). Finally, the qubit state is discriminated by an on-chip FDM demodulation algorithm. Fabricated by a 28-nm bulk CMOS process, the mixer-first reflectometer at 4 K achieves a minimum$T_{noise} =19$K at$f_{LO} =7.3$GHz with a 42-dB RX gain, which is highly competitive to other LNA-first reflectometers. In addition, thanks to the co-optimization of single-sideband (SSB) transmitter (TX), mixer-first RX and on-chip demodulation, under a baseband amplitude of$V_{pp}\sim 0.8$V, excellent spur-free dynamic range (SFDR) of SFDR > 45 dB and third-order intermodulation rejection of IMD$3\gt 50$dB are recorded. Lastly, the simultaneous FDM readout of two transmon qubits has also been demonstrated with fidelity 95.3% and 92.3% for qubit1 states$|0\rangle {\,}\& {\,}|1\rangle $, and fidelity 96.1% and 93.1% for qubit2 states$|0\rangle {\,}\& {\,}|1\rangle $, respectively.

IEEE Transactions on Microwave Theory and Techniques•Jul 21, 2026•1 citation

29.3 A Cryo-CMOS Receiver with 15K Noise Temperature Achieving 9.8dB SNR in 10μs Integration Time for Spin Qubit Readout

Bagas Prabowo, Oriol Pietx-Casas, Mohammad Ali Montazerolghaem +4 more

Continuous rounds of quantum error correction (QEC) are essential to achieve fault-tolerant quantum computers (QCs). In each QEC cycle, thousands of ancilla quantum bits (qubits) must be read out faster than the qubits’ decoherence time $(\gg \mathrm{T}_{2} * \sim 120 \mu \mathrm{s}$ for spin qubits). To address this urgent need, several CMOS receivers operating at cryogenic temperatures (cryo-CMOS RXs) have recently been introduced for gate-based [1] and RF reflectometry [2] readout of spin qubits, as well as transmons’ dispersive readout [3]. However, they have a few shortcomings. First, due to the temperature-independent shot noise of transistors in nanometer CMOS technology [4], their measured noise temperature $(\mathrm{T}_{{\mathrm {N}}})$ is limited to 40K, thus degrading qubit readout fidelity. Second, due to their large TN, prior art showed either only the electrical performance of their chips by applying a relatively large (i.e., -85dBm [2]) modulated signal directly to the RX input [2, 3] or offered limited qubit measurements by exploiting a HEMT amplifier prior to the RX [1]. Those issues hinder future monolithic integration between solid-state qubits and readout electronics. This work advances the prior art by (1) introducing a wideband passive amplification circuit at the RX front-end to minimize the shot noise contribution of the active devices, lowering prior art TNby $\sim 2.7\mathrm{x}$; (2) demonstrating the RX performance in an RF-reflectometry qubit readout scheme without using off-the-shelf LNA prior to the RX.

Digest of technical papers/Digest of technical papers - IEEE International Solid-State Circuits Conference•Feb 18, 2024•23 citations

A Passive Front-End Receiver for RF Reflectometry Readout in Spin Qubits

Bagas Prabowo, Oriol Pietx-Casas, Mohammad Ali Montazerolghaem +5 more

A scalable spin-qubit quantum processor requires fast, high-fidelity readout circuits operating at cryogenic temperatures (CTs). This work analyzes the radio frequency (RF) reflectometry readout mechanism to establish the link between conductance modulation, single-electron transistor (SET) matching network design, reflected signal power, and receiver (RX) noise temperature. Based on this analysis, a cryogenic RX architecture employing a passive switched-capacitor front-end is proposed. The front-end performs RF amplification and downconversion using transistors as switches, avoiding active RF amplification and mitigating shot-noise limitations. The RX is implemented in 40-nm CMOS and operates from 100 MHz to 2.2 GHz. Measurements demonstrate a minimum noise temperature of approximately 15 K at 4.2 K. When integrated with a quantum device, the RX achieves a signal-to-noise ratio (SNR) of 9.8 dB for a 10-µs integration time and enables 99.9% charge-state readout fidelity without external cryogenic amplifiers. This work represents the first demonstration of such fidelity using a cryo-CMOS RX and constitutes an important step toward scalable integration of qubit readout electronics.

IEEE Journal of Solid-State Circuits•Jan 1, 2026•0 citations

A Fully Integrated CMOS Parametric Amplifier for Cryogenic Qubit Readout

Gabriel López-Pinar, C. Aldea, Santiago Celma +1 more

Scalable quantum computing demands compact, low-power, and ultra-low-noise readout electronics at cryogenic temperatures. This work presents a fully integrated CMOS hybrid-less parametric amplifier for near-qubit preamplification at 5 GHz. Operating in a regime where the pump frequency is close to twice the signal frequency, the amplifier provides 10 dB of gain with reduced sensitivity to the input phase, thereby easing system tuning and minimizing the need for precise synchronization. It also presents effective idler suppression (18.4 dB) and pump isolation (52.8 dB), while eliminating bulky off-chip hybrids or circulators. The design occupies only $0.3 \mathrm{~mm}^{2}$ and consumes 10 mW, enabling full on-chip integration and improved scalability. Although the bandwidth (4.8-5 GHz) is narrower than some prior works, it remains sufficient for narrowband qubit readout, highlighting a practical trade-off between performance, compactness, and system complexity for scalable cryogenic quantum interfaces.

International Conference on Synthesis, Modeling, Analysis and Simulation Methods and Applications to Circuit Design•Jun 1, 2026•1 citation
In quantum computers, the quantum state discrimination of the physical quantum bits (Qubits) occupies ~80% of the quantum error correction (QEC) cycle. The RF reflectometry or dispersive readout determines the Qubit state by monitoring the RF reflection of the attached high-Q resonant tank. Compared to their dc counterparts, the RF reflectometers enjoy a high signal-to-noise ratio (SNR), low drifting, and fast speed. As a result, a high-fidelity, single-shot, scalable reflectometer array based on cryogenic CMOS (Cryo-CMOS) ICs is in demand for the future large-scale Qubit array (103∼10610^{3} {\sim } 10^{6}103∼106Qubits). However, the classic Cryo-CMOS heterodyne reflectometers, consisting of MOSFET-based LNA, mixer, and baseband blocks, suffer from high noise temperature and dc power. To address these issues, the Cryo-CMOS parametric circuitry based on varactors is explored. In this article, a dual-Qubit homodyne reflectometer array with 2 RX channels and 1 TX channel is demonstrated. In the RX, the degenerate parametric amplifier (DPA) enjoys a Q-enhanced,λRF/2\lambda _{\mathrm { RF}}/2λRF​/2differential-mode (DM) resonator for the high-gain parametric amplification. The common mode (CM) RF input of DPA interacts with the DM resonator by a nonreciprocal, dynamic mode coupling (DMC). It eliminates the necessity of a circulator and the potential oscillation of DPA. The scalability challenge of the DPA’s noise temperatureTnoiseT_{\mathrm { noise}}Tnoise​versus the environment temperatureTenvT_{\mathrm { env}}Tenv​is also investigated. In the TX, a current-mode logic (CML) divider with interstate locking and a vector modulator (VM) is implemented to achieve fast modulation for the spur and noise rejection. Measured at 4.2 K, the implemented 65 nm Cryo-CMOS chip presents a4.5∼74.5{\sim }74.5∼7GHz bandwidth, 52 dB peak RF gain, and 78 K noise temperature, and generates a 10 MHz TX pulse train with -22 dBm RF power and 30 dB tunability. It consumes a total dc power of 33 mW.
Error-corrected quantum computing does not only require large-scale (106–109) physical Qubit arrays but also relies on high-fidelity, scalable quantum-to-classic interface electronics. Quantum control and readout systems based on cryogenic CMOS integrated circuits mitigate the error of Qubit manipulation, reduce the cabling complexity, and facilitate the quantum feedback, which pave the way towards practical quantum error correction (QEC) and logic quantum gates. RF reflectometry is widely adopted for qubit states readout. Reflectometry conducts Qubit states discrimination (collapsed to “0” or “1”) by detecting the resonant frequency through RF reflection of a high-Q LC tank associated with the sensor Qubit (Fig. 1). The quantum states are encoded in either the amplitude or the phase of the reflected RF signal. Compared with its DC counterpart, the reflectometry achieves unprecedented charge sensitivity, reduces the integration time, and avoids long-term drifting. However, conventional heterodyne reflectometer schemes [1][4][5] adopt sophisticated up/down mixers, ADC, DAC, and PLL for the Qubit excitation and down-mixing, respectively. They suffer from poor TX-RX isolation, inter-modulation, and high DC power, which deteriorate the scalability and readout fidelity. To address these challenges, a highly scalable dual-Qubit homodyne reflectometer array is proposed in this paper. It drives the LC tank by a single PLL and detects the reflection by a high-gain degenerate parametric amplifier (DPA). Along with fast modulation and lock-in detection, it mitigates the interference, complex cabling, and high DC power of conventional heterodyne reflectometers.
Main-stream quantum computers employ dispersive reflectometry for quantum-bit (Qubit) state discrimination. An all-parametric quantum reflectometer (APQR) scheme has been proposed for high-fidelity, scalable Qubit array readout in this letter. For the RF excitation of APQR, a 10.7–16.9 GHz 65-nm cryogenic CMOS (Cryo-CMOS) parametric frequency divider (PFD) is demonstrated here. It adopts a pair of parallelly connected nonlinear artificial transmission lines (NLATLs), a wideband varactor-based dynamic coupler, and a transformer-based CM filter (TCMF). Due to the minimized device self-heating without dc power consumption and the intrinsic common-mode (CM) to differential-mode (DM) isolation, the PFD presents a measured output thermal noise floor of −189.1 dBm/Hz at 4.2 K. This is only 3.3 dB higher than 4.2-K blackbody radiation. At 4.2 K, the PFD also exhibits an ultralow phase noise of −128.8 dBc/Hz at 1 MHz at 6.75 GHz, which is 2.6 dB lower than a conventional Cryo-CMOS CML divider. It presents a 44.9% relative bandwidth at 4.2 K, which is$2\times $of the prior art at 300 K.
Quantum error correction (QEC) is in demand for a fault-tolerant quantum computer. Currently, the QEC cycle is bottlenecked by the quantum bit (qubit) readout. To this end, RF dispersive reflectometry with frequency division multiplexing (FDM) is preferred due to its high fidelity and scalability. However, for a low noise temperatureTnoiseT_{noise}Tnoise​, cryogenic low noise amplifiers (cryo-LNAs) of classic LNA-first reflectometers require high transconductance efficiency (gm2/Idg_{m}^{2}/I_{d}gm2​/Id​). These open-loop cryo-LNAs also present limited linearity under large output voltage, resulting in errors of FDM readout. In this work, a new approach, a mixer-first cryogenic CMOS (Cryo-CMOS) reflectometer, is explored for its potential advantages in noise and linearity. A passive, low-loss mixer directly down-converts the RF reflection from the qubits (5.5–8 GHz) at 4 K to IF/baseband (5–250 MHz). Then, an IF/baseband amplifier, employing a MOSFET pair of$W/L = 2{\,}\times {\,}800~\mu $m/100 nm and current density of$5~\mu A/A/A/\mu $m, achieves$2.8\times higherhigherhigherg_{m}^{2}/I_{d}thanCryo−CMOSLNAsforlownoise.Afterclosed−loopamplificationwithhighlinearity,thebasebandissampledbya500MSPS,12−bittime−interleaved(TI)analog−to−digitalconverter(ADC).Finally,thequbitstateisdiscriminatedbyanon−chipFDMdemodulationalgorithm.Fabricatedbya28−nmbulkCMOSprocess,themixer−firstreflectometerat4Kachievesaminimumthan Cryo-CMOS LNAs for low noise. After closed-loop amplification with high linearity, the baseband is sampled by a 500 MSPS, 12-bit time-interleaved (TI) analog-to-digital converter (ADC). Finally, the qubit state is discriminated by an on-chip FDM demodulation algorithm. Fabricated by a 28-nm bulk CMOS process, the mixer-first reflectometer at 4 K achieves a minimumthanCryo−CMOSLNAsforlownoise.Afterclosed−loopamplificationwithhighlinearity,thebasebandissampledbya500MSPS,12−bittime−interleaved(TI)analog−to−digitalconverter(ADC).Finally,thequbitstateisdiscriminatedbyanon−chipFDMdemodulationalgorithm.Fabricatedbya28−nmbulkCMOSprocess,themixer−firstreflectometerat4KachievesaminimumT_{noise} =19KatK atKatf_{LO} =7.3GHzwitha42−dBRXgain,whichishighlycompetitivetootherLNA−firstreflectometers.Inaddition,thankstotheco−optimizationofsingle−sideband(SSB)transmitter(TX),mixer−firstRXandon−chipdemodulation,underabasebandamplitudeofGHz with a 42-dB RX gain, which is highly competitive to other LNA-first reflectometers. In addition, thanks to the co-optimization of single-sideband (SSB) transmitter (TX), mixer-first RX and on-chip demodulation, under a baseband amplitude ofGHzwitha42−dBRXgain,whichishighlycompetitivetootherLNA−firstreflectometers.Inaddition,thankstotheco−optimizationofsingle−sideband(SSB)transmitter(TX),mixer−firstRXandon−chipdemodulation,underabasebandamplitudeofV_{pp}\sim 0.8$V, excellent spur-free dynamic range (SFDR) of SFDR > 45 dB and third-order intermodulation rejection of IMD3>503\gt 503>50dB are recorded. Lastly, the simultaneous FDM readout of two transmon qubits has also been demonstrated with fidelity 95.3% and 92.3% for qubit1 states$|0\rangle {\,}\& {\,}|1\rangle ,andfidelity96.1, and fidelity 96.1% and 93.1% for qubit2 states,andfidelity96.1|0\rangle {\,}\& {\,}|1\rangle $, respectively.
Continuous rounds of quantum error correction (QEC) are essential to achieve fault-tolerant quantum computers (QCs). In each QEC cycle, thousands of ancilla quantum bits (qubits) must be read out faster than the qubits’ decoherence time (≫T2∗∼120μs(\gg \mathrm{T}_{2} * \sim 120 \mu \mathrm{s}(≫T2​∗∼120μs for spin qubits). To address this urgent need, several CMOS receivers operating at cryogenic temperatures (cryo-CMOS RXs) have recently been introduced for gate-based [1] and RF reflectometry [2] readout of spin qubits, as well as transmons’ dispersive readout [3]. However, they have a few shortcomings. First, due to the temperature-independent shot noise of transistors in nanometer CMOS technology [4], their measured noise temperature (TN)(\mathrm{T}_{{\mathrm {N}}})(TN​) is limited to 40K, thus degrading qubit readout fidelity. Second, due to their large TN, prior art showed either only the electrical performance of their chips by applying a relatively large (i.e., -85dBm [2]) modulated signal directly to the RX input [2, 3] or offered limited qubit measurements by exploiting a HEMT amplifier prior to the RX [1]. Those issues hinder future monolithic integration between solid-state qubits and readout electronics. This work advances the prior art by (1) introducing a wideband passive amplification circuit at the RX front-end to minimize the shot noise contribution of the active devices, lowering prior art TNby ∼2.7x\sim 2.7\mathrm{x}∼2.7x; (2) demonstrating the RX performance in an RF-reflectometry qubit readout scheme without using off-the-shelf LNA prior to the RX.
A scalable spin-qubit quantum processor requires fast, high-fidelity readout circuits operating at cryogenic temperatures (CTs). This work analyzes the radio frequency (RF) reflectometry readout mechanism to establish the link between conductance modulation, single-electron transistor (SET) matching network design, reflected signal power, and receiver (RX) noise temperature. Based on this analysis, a cryogenic RX architecture employing a passive switched-capacitor front-end is proposed. The front-end performs RF amplification and downconversion using transistors as switches, avoiding active RF amplification and mitigating shot-noise limitations. The RX is implemented in 40-nm CMOS and operates from 100 MHz to 2.2 GHz. Measurements demonstrate a minimum noise temperature of approximately 15 K at 4.2 K. When integrated with a quantum device, the RX achieves a signal-to-noise ratio (SNR) of 9.8 dB for a 10-µs integration time and enables 99.9% charge-state readout fidelity without external cryogenic amplifiers. This work represents the first demonstration of such fidelity using a cryo-CMOS RX and constitutes an important step toward scalable integration of qubit readout electronics.
Scalable quantum computing demands compact, low-power, and ultra-low-noise readout electronics at cryogenic temperatures. This work presents a fully integrated CMOS hybrid-less parametric amplifier for near-qubit preamplification at 5 GHz. Operating in a regime where the pump frequency is close to twice the signal frequency, the amplifier provides 10 dB of gain with reduced sensitivity to the input phase, thereby easing system tuning and minimizing the need for precise synchronization. It also presents effective idler suppression (18.4 dB) and pump isolation (52.8 dB), while eliminating bulky off-chip hybrids or circulators. The design occupies only 0.3 mm20.3 \mathrm{~mm}^{2}0.3 mm2 and consumes 10 mW, enabling full on-chip integration and improved scalability. Although the bandwidth (4.8-5 GHz) is narrower than some prior works, it remains sufficient for narrowband qubit readout, highlighting a practical trade-off between performance, compactness, and system complexity for scalable cryogenic quantum interfaces.