Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

International Conference on Synthesis, Modeling, Analysis and Simulation Methods and Applications to Circuit Design

A Fully Integrated CMOS Parametric Amplifier for Cryogenic Qubit Readout

Gabriel López-Pinar, C. Aldea, Santiago Celma, Carlos Sánchez‐Azqueta

Published Jun 1, 2026• 1 citation
Publisher

Abstract

Scalable quantum computing demands compact, low-power, and ultra-low-noise readout electronics at cryogenic temperatures. This work presents a fully integrated CMOS hybrid-less parametric amplifier for near-qubit preamplification at 5 GHz. Operating in a regime where the pump frequency is close to twice the signal frequency, the amplifier provides 10 dB of gain with reduced sensitivity to the input phase, thereby easing system tuning and minimizing the need for precise synchronization. It also presents effective idler suppression (18.4 dB) and pump isolation (52.8 dB), while eliminating bulky off-chip hybrids or circulators. The design occupies only $0.3 \mathrm{~mm}^{2}$ and consumes 10 mW, enabling full on-chip integration and improved scalability. Although the bandwidth (4.8-5 GHz) is narrower than some prior works, it remains sufficient for narrowband qubit readout, highlighting a practical trade-off between performance, compactness, and system complexity for scalable cryogenic quantum interfaces.

DOI
10.1109/smacd70206.2026.11647813

Related papers

Design of fully integrated 45 nm CMOS system-on-chip receiver for readout of transmon qubit

Ahmad Salmanogli, Amine Bermak

This study presents a comprehensive design approach focusing on quantum chip signal amplification by Josephson parametric amplifiers, and an integrated receiver for detecting ultra-low-level quantum signals. Quantum theory is used to analyze the dynamics of a transmon qubit coupled to a transmission line, entanglement between them, and design a parametric amplifier to amplify the quantum signals. Integration of these quantum devices with a 45 nm CMOS system-on-chip receiver creates a sophisticated blend of quantum and classical elements. The transmon qubit and parametric amplifier as a quantum chip, operating at 10 mK, are evaluated for key quantum metrics such as entanglement, Stoke projector probabilities, and parametric amplifier gain. Simultaneously, the resulting receiver combines high-performance components, including a low-noise amplifier with 0.76 dB noise figure in a broad bandwidth, a sweepable 5.0 GHz sinusoidal wave generator, and a purpose-designed mixer for C-band to zero-intermediate frequency (IF) conversion. An intermediate frequency amplifier with flat 26 dB gain and its low-pass filter property generates a pure sinusoidal wave at zero-IF, suitable for subsequent processing at room temperature. This design achieves a notable balance with low power consumption (∼122 mW), a noise figure less than 0.9 dB, high gain (∼65 dB), a wide bandwidth of 3.6 GHz, and compact dimensions (0.6 × 0.4 mm2). The fully integrated receiver, capable of reading out at least 90 qubits, positions this design for potential applications in quantum computing. Post-simulation validations at room temperature underscore the promising and innovative nature of this approach.

arXiv:2401.04228•AVS Quantum Science•Dec 1, 2025•4 citations

Design of a Low-Noise Amplifier for Qubit Readout

Gabriel López-Pinar, Uxua Esteban Eraso, Santiago Celma +1 more

This work presents the design and optimization of a low-noise amplifier (LNA) for qubit readout in cryogenic environments of 3 − 4 K. The proposed LNA achieves wide bandwidth (4 GHz), high gain (47.0 dB), and sufficient linearity (IIP 3 = −34 dBm), while maintaining power consumption below 50 mW, making it suitable for integration into quantum computing systems. The amplifier is based on multi-stage cascode architectures with integrated inductances and impedance-matching techniques to optimize performance for a centre frequency of 5 GHz. While the results demonstrate good performance, there is still room for improvement in the S11parameter and the noise figure (NF ), which could benefit from a more refined transformer model. The proposed design represents a significant step toward integrating high-efficiency readout electronics into quantum computing architectures.

International Conference on Synthesis, Modeling, Analysis and Simulation Methods and Applications to Circuit Design•Jul 7, 2025•1 citation

Sub-mW/qubit 5.2-7.2GHz 65nm Cryo-CMOS RX for Scalable Quantum Computing Applications

Aravind Nagulu, Leonardo Ranzani, G. J. Riebell +3 more

Cryogenic CMOS control and readout circuits tightly interfaced with the qubits have emerged as a promising solution for future quantum computers with tens-of-thousands to millions of qubits [1] –[5]. A lownoise cryo-CMOS receiver at $3-4 \mathrm{~K}$ integrated tightly with the lowcryogenic quantum processor can relax or even potentially eliminated the need for the HEMT LNA, and keep the whole control loop at cryogenic temperature, hence avoiding any high-speed interconnects to room temperature (Fig. 1). Additionally, wide bandwidths in the receiver enables qubit-multiplexing, where qubits can be frequency multiplexed with a spacing of $10 \mathrm{MHz}-40 \mathrm{MHz}$, allowing anywhere from 10’s-100’s of qubits to be packed in to a single readout line with gigahertz-scale bandwidths. A second critical metric is power consumption, since the cooling power available in a typical dilution refrigerator is limited to a few watts at $3-4 \mathrm{~K}$. Therefore, the control and readout circuits should be designed with low power consumption, projected to be $\lt 1 \mathrm{~mW}$ per qubit (Fig. 1). While there has been initial progress in the design of cryo-CMOS readout systems, a leap forward is required in their overall power consumption to be viable for future quantum systems. In this work, we showcase the design and implementation of the first sub-mWper-qubit cryo-CMOS RX - a wideband, I/Q-downconversion, $4 \mathrm{~K}$ receiver for qubit readout that achieves $>1.9 \mathrm{GHz}$ of IF bandwidth with $>50 \mathrm{~dB}$ conversion gain and $0.7 \mathrm{~dB}$ NF while consuming only $17 \mathrm{~mW}$ of power consumption, thanks to various design techniques including near-threshold operation and low-1/f-noise passive mixers, representing $3-5 \times$ lower power consumption than prior works [2]–[3] while achieving similar noise, BW and gain performance. In addition, we demonstrate a real-time qubit read-out measurement by integrating our cryogenic-CMOS receiver with a transmon qubit.

Custom Integrated Circuits Conference•Apr 1, 2023•14 citations

A 5.5-7.9 GHz Double Quadrature Cryo-CMOS Receiver Featuring a Wideband Noise Matching LNA for Quantum Applications

Zixun Gao, Chenglong Liang, Suyuan Gan +5 more

This work introduces a broadband cryogenic receiver for scalable multiplexed readout of qubits. The receiver utilizes a double quadrature architecture with amplitude and phase error suppression. The hybrid poly-phase filter (PPF) is applied in the architecture to further reduce the input amplitude and phase errors at the radio frequency (RF) end, enhancing the circuit's overall error vector magnitude (EVM). To address the issue of wide bandwidth (BW) for qubit expansion, a low noise amplifier (LNA) with broadband input and noise matching and an improved four-input intermediate frequency amplifier (IF-AMP) with a resistance feedback structure are proposed, achieving a broadband gain response with high flatness. The chip has been designed in standard 55 nm CMOS technology. The LNA achieves a measured power gain of 27.4 dB at 5 GHz with a -3 dB BW of 5.2 GHz at 6 K. Across the entire band of interest, the measured noise figure (NF) deviates by just 0.15 dB from the minimum noise figure (NFmin) and less than 2 dB at 300K, while the measured cryogenic NF falls within the range of 0.79-1 dB. The LNA consumes only 5.5 mW from a 1.2 V supply. Simulation results of the designed receiver indicate that it delivers an average gain of 49.5 dB with a -3 dB BW of 2.4 GHz and an image rejection ratio (IRR) exceeding 40 dB at 300 K.

IEEE International Symposium on Circuits and Systems proceedings•May 25, 2025•2 citations

Cryogenic CMOS Integrated Circuits for Scalable Readout of Silicon Quantum Computers

Andrea Ruffino

Quantum computing promises to revolutionize our lives, achieving unprecedented computational powers and unlocking new possibilities in drug discovery, chemical simulations and cryptography. The fundamental unit of computation of a quantum computer is the quantum bit (qubit). It can be implemented in a number of technologies, such as superconducting qubits, spin qubits, photonic systems, trapped ions and NV-centers. Solid-state superconducting qubits and spin qubits seem to be the most promising ones, as shown by the recent demonstration of quantum supremacy with a superconducting qubit processor. Such quantum processors, to operate in the quantum regime, require very low temperatures around 10 mK, and they are hence kept inside dilution fridges. The electronics required to read out and control such processors is typically realized by discrete components or bulky scientific instruments at room temperature wired into the dilution fridge. Such approach is only feasible until few (< 100) qubits are handled, but it is not scalable for million-qubit processors required for fault-tolerant operation. In this thesis, readout and control electronics is proposed to be integrated and operated directly at cryogenic temperatures, in close proximity with the qubits and potentially even co-integrated. CMOS technology is advocated for its scalability, compactness and low prototyping cost, to create a comprehensive cryo-CMOS class of fully-integrated transceivers to read out and control solid-state qubits. In particular, the thesis focuses on cryo-CMOS radio-frequency integrated circuits for the readout of silicon quantum computers, looking to integrate the whole readout system, from the quantum layer to the room temperature user interface. Cryogenic CMOS devices are explored first, to lay the foundations of integrated circuit design. The realization of quantum dots in standard CMOS technology is explored as a platform to realize solid-state qubit arrays, demonstrating functionality at 50 mK and good reproducibility. Moreover, the operation of integrated transistors at 50 mK and 4.2 K is explored to understand their basic cryogenic functionality, through characterization and modeling. Then also integrated passives, such as capacitors, inductors and transformers, are studied and modeled at cryogenic temperatures. Then, a fully-integrated readout platform spanning across all the blocks needed for dispersive readout is proposed. A fully-integrated matrix of quantum dots with radio-frequency gate-based readout capabilities is demonstrated along with time- and frequency-multiplexing. This quantum-classical circuit shows all the features for a scalable approach and is the core of the platform following it. A cryogenic CMOS circulator based on a new all-pass filter architecture is demonstrated, to be used as integrated replacement for current bulky counterparts; it allows power reduction, insertion loss and bandwidth enhancement with respect to state-of-the-art integrated circulators. The rest of the front-end is also explored with dedicated test multiplexers, a low noise-amplifier and an oscillator, that are finally merged in a single fully-integrated low-noise receiver with frequency synthesizer operating at 3.5 K for scalable multiplexed readout of silicon qubits. The platform presented in this thesis, across temperature boundaries, carries all the features required for future scalable silicon quantum computing platforms and could therefore form their core.

•Jan 1, 2021•0 citations

A Cryo-Tolerant >40-dB IRR, 4.7–7.9-GHz Double Quadrature Cryo-CMOS Receiver With a Broadband LNA for Scalable Quantum Applications

Zixun Gao, Chenglong Liang, Ruixin Liang +7 more

This article presents a cryogenic CMOS receiver operating across 4.7–7.9 GHz for frequency-division multiplexing (FDM) quantum state readout. The designed receiver employs a double quadrature (DQ) architecture and a hybrid poly-phase filter (PPF) is proposed to achieve an impressive image rejection ratio (IRR) to meet the 99.99% higher fidelity requirements in quantum error correction (QEC). In addition, gain tuning at different stages of the low noise amplifier (LNA) facilitates a broadband gain and flatness, while the subsequent receiver chains of a broadband mixer and an improved four-input intermediate frequency amplifier (IF-AMP) provide further gain compensation. Fabricated with a standard 55-nm CMOS technology, the LNA achieves a measured power gain of 27.4 dB, with a −3-dB bandwidth (BW) of 5.2 GHz at 6 K. The measured cryogenic noise figure (NF) ranges from 0.79 to 1 dB consuming merely 5.5 mW from a 1.2-V supply. Overall receiver measurements demonstrate a peak gain of 48.2 dB, a −5-dB flatness of 3.2 GHz, and an IRR that exceeds 40 dB at 6 K. These results demonstrate the receiver’s capacity for high-fidelity qubits’ state readout.

IEEE Transactions on Very Large Scale Integration (VLSI) Systems•Aug 26, 2025•2 citations
Scalable quantum computing demands compact, low-power, and ultra-low-noise readout electronics at cryogenic temperatures. This work presents a fully integrated CMOS hybrid-less parametric amplifier for near-qubit preamplification at 5 GHz. Operating in a regime where the pump frequency is close to twice the signal frequency, the amplifier provides 10 dB of gain with reduced sensitivity to the input phase, thereby easing system tuning and minimizing the need for precise synchronization. It also presents effective idler suppression (18.4 dB) and pump isolation (52.8 dB), while eliminating bulky off-chip hybrids or circulators. The design occupies only 0.3 mm20.3 \mathrm{~mm}^{2}0.3 mm2 and consumes 10 mW, enabling full on-chip integration and improved scalability. Although the bandwidth (4.8-5 GHz) is narrower than some prior works, it remains sufficient for narrowband qubit readout, highlighting a practical trade-off between performance, compactness, and system complexity for scalable cryogenic quantum interfaces.
This study presents a comprehensive design approach focusing on quantum chip signal amplification by Josephson parametric amplifiers, and an integrated receiver for detecting ultra-low-level quantum signals. Quantum theory is used to analyze the dynamics of a transmon qubit coupled to a transmission line, entanglement between them, and design a parametric amplifier to amplify the quantum signals. Integration of these quantum devices with a 45 nm CMOS system-on-chip receiver creates a sophisticated blend of quantum and classical elements. The transmon qubit and parametric amplifier as a quantum chip, operating at 10 mK, are evaluated for key quantum metrics such as entanglement, Stoke projector probabilities, and parametric amplifier gain. Simultaneously, the resulting receiver combines high-performance components, including a low-noise amplifier with 0.76 dB noise figure in a broad bandwidth, a sweepable 5.0 GHz sinusoidal wave generator, and a purpose-designed mixer for C-band to zero-intermediate frequency (IF) conversion. An intermediate frequency amplifier with flat 26 dB gain and its low-pass filter property generates a pure sinusoidal wave at zero-IF, suitable for subsequent processing at room temperature. This design achieves a notable balance with low power consumption (∼122 mW), a noise figure less than 0.9 dB, high gain (∼65 dB), a wide bandwidth of 3.6 GHz, and compact dimensions (0.6 × 0.4 mm2). The fully integrated receiver, capable of reading out at least 90 qubits, positions this design for potential applications in quantum computing. Post-simulation validations at room temperature underscore the promising and innovative nature of this approach.
This work presents the design and optimization of a low-noise amplifier (LNA) for qubit readout in cryogenic environments of 3 − 4 K. The proposed LNA achieves wide bandwidth (4 GHz), high gain (47.0 dB), and sufficient linearity (IIP 3 = −34 dBm), while maintaining power consumption below 50 mW, making it suitable for integration into quantum computing systems. The amplifier is based on multi-stage cascode architectures with integrated inductances and impedance-matching techniques to optimize performance for a centre frequency of 5 GHz. While the results demonstrate good performance, there is still room for improvement in the S11parameter and the noise figure (NF ), which could benefit from a more refined transformer model. The proposed design represents a significant step toward integrating high-efficiency readout electronics into quantum computing architectures.
Cryogenic CMOS control and readout circuits tightly interfaced with the qubits have emerged as a promising solution for future quantum computers with tens-of-thousands to millions of qubits [1] –[5]. A lownoise cryo-CMOS receiver at 3−4 K3-4 \mathrm{~K}3−4 K integrated tightly with the lowcryogenic quantum processor can relax or even potentially eliminated the need for the HEMT LNA, and keep the whole control loop at cryogenic temperature, hence avoiding any high-speed interconnects to room temperature (Fig. 1). Additionally, wide bandwidths in the receiver enables qubit-multiplexing, where qubits can be frequency multiplexed with a spacing of 10MHz−40MHz10 \mathrm{MHz}-40 \mathrm{MHz}10MHz−40MHz, allowing anywhere from 10’s-100’s of qubits to be packed in to a single readout line with gigahertz-scale bandwidths. A second critical metric is power consumption, since the cooling power available in a typical dilution refrigerator is limited to a few watts at 3−4 K3-4 \mathrm{~K}3−4 K. Therefore, the control and readout circuits should be designed with low power consumption, projected to be <1 mW\lt 1 \mathrm{~mW}<1 mW per qubit (Fig. 1). While there has been initial progress in the design of cryo-CMOS readout systems, a leap forward is required in their overall power consumption to be viable for future quantum systems. In this work, we showcase the design and implementation of the first sub-mWper-qubit cryo-CMOS RX - a wideband, I/Q-downconversion, 4 K4 \mathrm{~K}4 K receiver for qubit readout that achieves >1.9GHz>1.9 \mathrm{GHz}>1.9GHz of IF bandwidth with >50 dB>50 \mathrm{~dB}>50 dB conversion gain and 0.7 dB0.7 \mathrm{~dB}0.7 dB NF while consuming only 17 mW17 \mathrm{~mW}17 mW of power consumption, thanks to various design techniques including near-threshold operation and low-1/f-noise passive mixers, representing 3−5×3-5 \times3−5× lower power consumption than prior works [2]–[3] while achieving similar noise, BW and gain performance. In addition, we demonstrate a real-time qubit read-out measurement by integrating our cryogenic-CMOS receiver with a transmon qubit.
This work introduces a broadband cryogenic receiver for scalable multiplexed readout of qubits. The receiver utilizes a double quadrature architecture with amplitude and phase error suppression. The hybrid poly-phase filter (PPF) is applied in the architecture to further reduce the input amplitude and phase errors at the radio frequency (RF) end, enhancing the circuit's overall error vector magnitude (EVM). To address the issue of wide bandwidth (BW) for qubit expansion, a low noise amplifier (LNA) with broadband input and noise matching and an improved four-input intermediate frequency amplifier (IF-AMP) with a resistance feedback structure are proposed, achieving a broadband gain response with high flatness. The chip has been designed in standard 55 nm CMOS technology. The LNA achieves a measured power gain of 27.4 dB at 5 GHz with a -3 dB BW of 5.2 GHz at 6 K. Across the entire band of interest, the measured noise figure (NF) deviates by just 0.15 dB from the minimum noise figure (NFmin) and less than 2 dB at 300K, while the measured cryogenic NF falls within the range of 0.79-1 dB. The LNA consumes only 5.5 mW from a 1.2 V supply. Simulation results of the designed receiver indicate that it delivers an average gain of 49.5 dB with a -3 dB BW of 2.4 GHz and an image rejection ratio (IRR) exceeding 40 dB at 300 K.
Quantum computing promises to revolutionize our lives, achieving unprecedented computational powers and unlocking new possibilities in drug discovery, chemical simulations and cryptography. The fundamental unit of computation of a quantum computer is the quantum bit (qubit). It can be implemented in a number of technologies, such as superconducting qubits, spin qubits, photonic systems, trapped ions and NV-centers. Solid-state superconducting qubits and spin qubits seem to be the most promising ones, as shown by the recent demonstration of quantum supremacy with a superconducting qubit processor. Such quantum processors, to operate in the quantum regime, require very low temperatures around 10 mK, and they are hence kept inside dilution fridges. The electronics required to read out and control such processors is typically realized by discrete components or bulky scientific instruments at room temperature wired into the dilution fridge. Such approach is only feasible until few (< 100) qubits are handled, but it is not scalable for million-qubit processors required for fault-tolerant operation. In this thesis, readout and control electronics is proposed to be integrated and operated directly at cryogenic temperatures, in close proximity with the qubits and potentially even co-integrated. CMOS technology is advocated for its scalability, compactness and low prototyping cost, to create a comprehensive cryo-CMOS class of fully-integrated transceivers to read out and control solid-state qubits. In particular, the thesis focuses on cryo-CMOS radio-frequency integrated circuits for the readout of silicon quantum computers, looking to integrate the whole readout system, from the quantum layer to the room temperature user interface. Cryogenic CMOS devices are explored first, to lay the foundations of integrated circuit design. The realization of quantum dots in standard CMOS technology is explored as a platform to realize solid-state qubit arrays, demonstrating functionality at 50 mK and good reproducibility. Moreover, the operation of integrated transistors at 50 mK and 4.2 K is explored to understand their basic cryogenic functionality, through characterization and modeling. Then also integrated passives, such as capacitors, inductors and transformers, are studied and modeled at cryogenic temperatures. Then, a fully-integrated readout platform spanning across all the blocks needed for dispersive readout is proposed. A fully-integrated matrix of quantum dots with radio-frequency gate-based readout capabilities is demonstrated along with time- and frequency-multiplexing. This quantum-classical circuit shows all the features for a scalable approach and is the core of the platform following it. A cryogenic CMOS circulator based on a new all-pass filter architecture is demonstrated, to be used as integrated replacement for current bulky counterparts; it allows power reduction, insertion loss and bandwidth enhancement with respect to state-of-the-art integrated circulators. The rest of the front-end is also explored with dedicated test multiplexers, a low noise-amplifier and an oscillator, that are finally merged in a single fully-integrated low-noise receiver with frequency synthesizer operating at 3.5 K for scalable multiplexed readout of silicon qubits. The platform presented in this thesis, across temperature boundaries, carries all the features required for future scalable silicon quantum computing platforms and could therefore form their core.
This article presents a cryogenic CMOS receiver operating across 4.7–7.9 GHz for frequency-division multiplexing (FDM) quantum state readout. The designed receiver employs a double quadrature (DQ) architecture and a hybrid poly-phase filter (PPF) is proposed to achieve an impressive image rejection ratio (IRR) to meet the 99.99% higher fidelity requirements in quantum error correction (QEC). In addition, gain tuning at different stages of the low noise amplifier (LNA) facilitates a broadband gain and flatness, while the subsequent receiver chains of a broadband mixer and an improved four-input intermediate frequency amplifier (IF-AMP) provide further gain compensation. Fabricated with a standard 55-nm CMOS technology, the LNA achieves a measured power gain of 27.4 dB, with a −3-dB bandwidth (BW) of 5.2 GHz at 6 K. The measured cryogenic noise figure (NF) ranges from 0.79 to 1 dB consuming merely 5.5 mW from a 1.2-V supply. Overall receiver measurements demonstrate a peak gain of 48.2 dB, a −5-dB flatness of 3.2 GHz, and an IRR that exceeds 40 dB at 6 K. These results demonstrate the receiver’s capacity for high-fidelity qubits’ state readout.