Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Microscopy and Microanalysis

Unraveling the Connection between Deposition, Microstructure, and Performance of Superconducting Quantum Circuits using Multi-modal Electron Microscopy

Jin‐Su Oh, Cameron Kopas, Jayss Marshall, Xiaotian Fang, Kamal R. Joshi, Amlan Datta, Sunil Ghimire, Joong‐Mok Park, Richard H. J. Kim, Daniel Setiawan, Ella Lachman, J. Mutus, Akshay A. Murthy, Anna Grassellino, Alexander Romanenko, John Francis Zasadzinski, Jigang Wang, R. Prozorov, Kameshwar K. Yadavalli, Matt J. Kramer, Lin Zhou

Published Jul 1, 2024• 0 citations
Publisher

Abstract

Superconducting quantum circuits (SQC) are one of the contender hardware platforms for quantum computing. Nonetheless, the advent of fault-tolerant operation has been constrained by insufficient lifetime T1 [1]. The structural and chemical defects at the interfaces and surfaces of SQC, arising from the established semiconductor fabrication techniques, such as thin film deposition and lithography, negatively affect device coherence [2]. Therefore, it is essential to understand the micro and chemical structural features at the atomic scale that may act as sources of decoherence factors in both superconducting qubits and coplanar waveguide (CPW) resonators, which are key components of SQC. In this study, we performed a comprehensive investigation on microstructures, superconductivity, and internal quality factors of Nb CPW resonators deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current magnetron sputtering (DCMS). Fig. 1a-c shows that niobium (Nb) resonators fabricated using HiPIMS (Fig. 1a) exhibit a smaller average grain size compared to two samples deposited by DCMS; one is deposited using power variation from low to high, and the other is deposited at high-power (Fig. 1b-c). We identified that grain size is highly related to two-level system (TLS) sources (Fig. 1d), while crystalline defects originating from discontinuous deposition are contributors to power-independent non-TLS sources (Fig. 1e). This study highlights different aspects of superconducting metal deposition engineering for enhanced performances of SQC [3]. Plan-view TEM images of Nb thin films deposited by (a)HiPIMS, (b) Low to high-power DC sputtering, and (c) High power DC sputtering. Measured (a) TLS loss and (b) power-independent loss extracted by power-dependent internal quality factor measurement.

DOI
10.1093/mam/ozae044.766

Related papers

Exploring the relationship between deposition method, microstructure, and performance of Nb/Si-based superconducting coplanar waveguide resonators

Jin‐Su Oh, Cameron Kopas, Jayss Marshall +18 more

Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. In this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.

Acta Materialia•Jul 4, 2024•21 citations

Microwave Loss Characteristics of Nb Films for Quantum Computing

Bektur Abdisatarov, Bafia, D, Murthy, A +9 more

Niobium films typically constitute a significant component in the construction of modern two-dimensional superconducting qubit architectures, yet their contribution to the total decay rate is not fully understood, making it difficult to definitively identify dominant loss channels in present designs. We present the first study, which correlates direct measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radiofrequency (SRF) resonator. Our findings indicate that microwave dissipation in the HiPIMS-prepared niobium films, within the quantum regime, resembles that of record-high intrinsic quality factor of bulk niobium SRF cavities, with lifetimes extending into seconds. Microstructure and impurity level of the niobium film do not significantly affect the losses. These results set the scale of microwave losses in niobium films and show that niobium losses do not dominate the observed coherence times in present two-dimensional superconducting qubit designs, instead highlighting the role of the dielectric oxide in limiting the performance.

•Dec 6, 2024•0 citations

Tantalum-Encapsulated Niobium Superconducting Resonators: High Internal Quality Factor and Improved Temporal Stability via Surface Passivation

Anas Alkhazaleh, Juan Villegas, Florent Ravaux +1 more

Superconducting coplanar waveguide resonators are essential components in quantum processors, where their internal quality factor (Qi) constrains qubit coherence and readout fidelity. In niobium devices, microwave losses at millikelvin temperatures are strongly influenced by two-level systems (TLS) associated with the complex NbOx surface oxide. To mitigate these losses, we investigate a surface-engineering approach in which Nb films are capped in situ with a thin tantalum layer to suppress Nb2O5 formation and replace the native NbOx interface with a Ta-based oxide. We fabricate Nb/Ta bilayer and reference Nb resonators on high-resistivity silicon using identical DC sputtering and wet etching conditions, and characterize their performance at millikelvin temperatures. Fresh Ta-encapsulated devices exhibit internal quality factors up to 2.4 x 10^6 in the near-single-photon regime, with power dependence consistent with reduced TLS-related loss at the metal-air interface. A control Nb device fabricated under the same process shows comparatively lower Q_TLS, consistent with the beneficial effect of the Ta capping layer. Furthermore, ageing tests performed on Nb/Ta resonators after six months reveal a moderate reduction in Q_TLS relative to their initial values, yet the performance remains superior to newly fabricated Nb-only devices. These results suggest that thin Ta encapsulation enhances interface quality and contributes to improved temporal stability while remaining compatible with Nb-based fabrication workflows.

quant-pharXiv:2604.09050•Apr 13, 2026•2 citations

The effect of niobium thin film structure on losses in superconducting circuits

Maxwell Drimmer, Sjoerd Telkamp, Felix L Fischer +7 more

Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.

arXiv:2403.12164•Materials for Quantum Technology•Oct 14, 2025•22 citations

Developing Best Practice Fabrication for Niobium Superconducting Devices

Jadrien T. Paustian

Superconducting qubits are a leading platform for scalable quantum computation. This platform offers high gate speeds and can make use of readily scalable complementary metal-oxide semiconductor (CMOS) fabrication techniques. However, superconducting qubits are susceptible to a variety of losses that arise in systems with superconductors, such as due to ubiquitous two-level systems, quasiparticles, and more. Designing fabrication processes to mitigate and manage these loss sources is critical to achieving scalable quantum computation. However, many of these loss sources are set during fabrication processing, of which there can be many different steps, each with its own parameter space. Exploring this space with qubits would be prohibitively time-consuming. Coplanar waveguide resonators provide a suitable proxy system for minimizing loss while costing less time and money to fabricate and measure. In this thesis, we explore the results of such an optimization performed on niobium resonators. Niobium is a widely used material platform for superconducting qubit circuits. We report highly consistent state-of-the-art resonator quality factors, with clear improvements over the previous fabrication recipe, and correlate the observed improvements to the internal quality factors with microstructural changes induced by hydrofluoric acid treatment, photoresist stripping, and choice of sputter deposition conditions. Additionally, we provide a detailed description of our fab process to ensure reproducibility in other lab facilities. Finally, we address some intriguing anomalies uncovered in temperature-dependent quality factors of the niobium resonators and show a correlation of the quality factors with compressive film stress.

•Dec 24, 2025•0 citations

Superconducting thin films and hybrid materials for quantum devices

Sjoerd Telkamp

The performance and coherence of superconducting quantum systems are fundamentally tied to the quality of the materials from which they are built. In superconducting transmon qubits, many loss mechanisms and sources of decoherence originate from material imperfections or unwanted oxide formation. Likewise, semiconductor–superconductor hybrid systems depend on high-quality interfaces to ensure strong coupling between electronic states in the two materials. In such hybrid devices, the accessible operating regime is often dictated by the intrinsic material properties of either the semiconductor or the superconductor. Advancing quantum device performance therefore requires exploring new material systems and optimizing their physical characteristics. In this thesis, we present the development of several superconducting material platforms for quantum technologies, including superconducting qubits, single-photon detectors, and semiconductor superconductor hybrid devices. We focus on the growth and characterization of superconducting films and heterostructures, and we establish clear connections between their material properties and the resulting device performance. First, we will present a novel semiconductor-superconductor hybrid material based on in-situ deposited epitaxial layers of Nb and Al on a shallow InAs quantum well. In this structure, the Al interlayer provides an epitaxial connection between an in-situ magnetron sputtered Nb or NbTi thin film and a shallow InAs two dimensional electron gas. This metal-to-metal epitaxy is achieved by optimization of the material stack and results in an induced superconducting gap of approximately 1 meV, determined from transport measurements of superconductor semiconductor Josephson junctions. This induced gap is approximately five times larger than the values reported for Al-based hybrid materials and indicates the formation of highly-transparent interfaces that are required in high-quality hybrid material platforms. Then, we discuss a different approach in the next chapter where we develop a hybrid material based on a molecular beam epitaxy grown InAsSb surface quantum well with an in-situ deposited Nb layer directly on top of the quantum well. Relative to conventional Al-InAs based systems, the InAsSb surface quantum well offers a lower effective mass and stronger spin-orbit interaction, while the Nb layer has a higher critical temperature and a larger critical magnetic field. The in-situ deposition of the Nb layer directly on top of the quantum well results in a high-quality interface that enables strong coupling to the InAsSb quantum well. Transport measurements on Josephson junctions reveal an induced superconducting gap of 1.3 meV and a critical current density of 3.75 × 10³A/cm². Furthermore, a planar asymmetric SQUID is realized, exhibiting gate-tunable superimposed oscillations originating from both the individual Josephson junction and the full SQUID loop. The large induced superconducting gap combined with strong spin-orbit interaction position this material as an attractive platform for experiments exploring gate-tunable superconductivity and topological superconducting devices. In the next chapter, we will focus on establishing a link between Nb film crystal properties and their performance in superconducting circuits. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10⁶ at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasi-particle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Then, we explore yet a different material platform by attempting to realize onchip NbTiN single photon detectors on LiNbO₃, an emerging photonic platform with high potential for scalable quantum information processing. We use DC reactive magnetron sputtering to grow high-quality NbTiN thin films and investigate the impact of substrate temperature during NbTiN growth. We achieve four nm thick superconducting films with a critical temperature (𝑇𝑐) of 12.3 K grown at a substrate temperature of 825 K. We demonstrate that the increased substrate temperature reduces the oxygen concentration in our films and improves the overall stoichiometry. In addition, we integrate these films with the LiNbO3 platform and investigate the obtained interface quality. Finally, we fabricate superconducting nanowire single photon detectors from the NbTiN film on LiNbO₃ and characterize the detector performance. Lastly, we report a gate-tunable Josephson diode effect in hybrid nanowire junctions consisting of a spin-orbit-coupled semiconductor core coated with epitaxial ferromagnetic insulator and superconductor shells. The wires display a hysteretic superconducting window as a function of axial magnetic field. In the superconducting regime, the devices exhibit nonreciprocal current transport, with the diode efficiency showing a strong dependence on back-gate voltage. The effect persists in a remanent magnetization state following a controlled demagnetization procedure, establishing zero-field operation. The combination of results presented in this thesis stress the importance of a material-focused approach in advancing the performance of quantum hardware. The novel hybrid material platforms developed in this thesis expand the operating regime of devices, which could enable future experiments involving gate-tunable superconductivity or topological properties. Similarly, we demonstrate that optimizing superconductor crystal structure benefits quantum devices, such as single-photon detectors and superconducting resonators.

•Jan 1, 2026•0 citations
Superconducting quantum circuits (SQC) are one of the contender hardware platforms for quantum computing. Nonetheless, the advent of fault-tolerant operation has been constrained by insufficient lifetime T1 [1]. The structural and chemical defects at the interfaces and surfaces of SQC, arising from the established semiconductor fabrication techniques, such as thin film deposition and lithography, negatively affect device coherence [2]. Therefore, it is essential to understand the micro and chemical structural features at the atomic scale that may act as sources of decoherence factors in both superconducting qubits and coplanar waveguide (CPW) resonators, which are key components of SQC. In this study, we performed a comprehensive investigation on microstructures, superconductivity, and internal quality factors of Nb CPW resonators deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current magnetron sputtering (DCMS). Fig. 1a-c shows that niobium (Nb) resonators fabricated using HiPIMS (Fig. 1a) exhibit a smaller average grain size compared to two samples deposited by DCMS; one is deposited using power variation from low to high, and the other is deposited at high-power (Fig. 1b-c). We identified that grain size is highly related to two-level system (TLS) sources (Fig. 1d), while crystalline defects originating from discontinuous deposition are contributors to power-independent non-TLS sources (Fig. 1e). This study highlights different aspects of superconducting metal deposition engineering for enhanced performances of SQC [3]. Plan-view TEM images of Nb thin films deposited by (a)HiPIMS, (b) Low to high-power DC sputtering, and (c) High power DC sputtering. Measured (a) TLS loss and (b) power-independent loss extracted by power-dependent internal quality factor measurement.
Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. In this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.
Niobium films typically constitute a significant component in the construction of modern two-dimensional superconducting qubit architectures, yet their contribution to the total decay rate is not fully understood, making it difficult to definitively identify dominant loss channels in present designs. We present the first study, which correlates direct measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radiofrequency (SRF) resonator. Our findings indicate that microwave dissipation in the HiPIMS-prepared niobium films, within the quantum regime, resembles that of record-high intrinsic quality factor of bulk niobium SRF cavities, with lifetimes extending into seconds. Microstructure and impurity level of the niobium film do not significantly affect the losses. These results set the scale of microwave losses in niobium films and show that niobium losses do not dominate the observed coherence times in present two-dimensional superconducting qubit designs, instead highlighting the role of the dielectric oxide in limiting the performance.
Superconducting coplanar waveguide resonators are essential components in quantum processors, where their internal quality factor (Qi) constrains qubit coherence and readout fidelity. In niobium devices, microwave losses at millikelvin temperatures are strongly influenced by two-level systems (TLS) associated with the complex NbOx surface oxide. To mitigate these losses, we investigate a surface-engineering approach in which Nb films are capped in situ with a thin tantalum layer to suppress Nb2O5 formation and replace the native NbOx interface with a Ta-based oxide. We fabricate Nb/Ta bilayer and reference Nb resonators on high-resistivity silicon using identical DC sputtering and wet etching conditions, and characterize their performance at millikelvin temperatures. Fresh Ta-encapsulated devices exhibit internal quality factors up to 2.4 x 10^6 in the near-single-photon regime, with power dependence consistent with reduced TLS-related loss at the metal-air interface. A control Nb device fabricated under the same process shows comparatively lower Q_TLS, consistent with the beneficial effect of the Ta capping layer. Furthermore, ageing tests performed on Nb/Ta resonators after six months reveal a moderate reduction in Q_TLS relative to their initial values, yet the performance remains superior to newly fabricated Nb-only devices. These results suggest that thin Ta encapsulation enhances interface quality and contributes to improved temporal stability while remaining compatible with Nb-based fabrication workflows.
Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
Superconducting qubits are a leading platform for scalable quantum computation. This platform offers high gate speeds and can make use of readily scalable complementary metal-oxide semiconductor (CMOS) fabrication techniques. However, superconducting qubits are susceptible to a variety of losses that arise in systems with superconductors, such as due to ubiquitous two-level systems, quasiparticles, and more. Designing fabrication processes to mitigate and manage these loss sources is critical to achieving scalable quantum computation. However, many of these loss sources are set during fabrication processing, of which there can be many different steps, each with its own parameter space. Exploring this space with qubits would be prohibitively time-consuming. Coplanar waveguide resonators provide a suitable proxy system for minimizing loss while costing less time and money to fabricate and measure. In this thesis, we explore the results of such an optimization performed on niobium resonators. Niobium is a widely used material platform for superconducting qubit circuits. We report highly consistent state-of-the-art resonator quality factors, with clear improvements over the previous fabrication recipe, and correlate the observed improvements to the internal quality factors with microstructural changes induced by hydrofluoric acid treatment, photoresist stripping, and choice of sputter deposition conditions. Additionally, we provide a detailed description of our fab process to ensure reproducibility in other lab facilities. Finally, we address some intriguing anomalies uncovered in temperature-dependent quality factors of the niobium resonators and show a correlation of the quality factors with compressive film stress.
The performance and coherence of superconducting quantum systems are fundamentally tied to the quality of the materials from which they are built. In superconducting transmon qubits, many loss mechanisms and sources of decoherence originate from material imperfections or unwanted oxide formation. Likewise, semiconductor–superconductor hybrid systems depend on high-quality interfaces to ensure strong coupling between electronic states in the two materials. In such hybrid devices, the accessible operating regime is often dictated by the intrinsic material properties of either the semiconductor or the superconductor. Advancing quantum device performance therefore requires exploring new material systems and optimizing their physical characteristics. In this thesis, we present the development of several superconducting material platforms for quantum technologies, including superconducting qubits, single-photon detectors, and semiconductor superconductor hybrid devices. We focus on the growth and characterization of superconducting films and heterostructures, and we establish clear connections between their material properties and the resulting device performance. First, we will present a novel semiconductor-superconductor hybrid material based on in-situ deposited epitaxial layers of Nb and Al on a shallow InAs quantum well. In this structure, the Al interlayer provides an epitaxial connection between an in-situ magnetron sputtered Nb or NbTi thin film and a shallow InAs two dimensional electron gas. This metal-to-metal epitaxy is achieved by optimization of the material stack and results in an induced superconducting gap of approximately 1 meV, determined from transport measurements of superconductor semiconductor Josephson junctions. This induced gap is approximately five times larger than the values reported for Al-based hybrid materials and indicates the formation of highly-transparent interfaces that are required in high-quality hybrid material platforms. Then, we discuss a different approach in the next chapter where we develop a hybrid material based on a molecular beam epitaxy grown InAsSb surface quantum well with an in-situ deposited Nb layer directly on top of the quantum well. Relative to conventional Al-InAs based systems, the InAsSb surface quantum well offers a lower effective mass and stronger spin-orbit interaction, while the Nb layer has a higher critical temperature and a larger critical magnetic field. The in-situ deposition of the Nb layer directly on top of the quantum well results in a high-quality interface that enables strong coupling to the InAsSb quantum well. Transport measurements on Josephson junctions reveal an induced superconducting gap of 1.3 meV and a critical current density of 3.75 × 10³A/cm². Furthermore, a planar asymmetric SQUID is realized, exhibiting gate-tunable superimposed oscillations originating from both the individual Josephson junction and the full SQUID loop. The large induced superconducting gap combined with strong spin-orbit interaction position this material as an attractive platform for experiments exploring gate-tunable superconductivity and topological superconducting devices. In the next chapter, we will focus on establishing a link between Nb film crystal properties and their performance in superconducting circuits. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10⁶ at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasi-particle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Then, we explore yet a different material platform by attempting to realize onchip NbTiN single photon detectors on LiNbO₃, an emerging photonic platform with high potential for scalable quantum information processing. We use DC reactive magnetron sputtering to grow high-quality NbTiN thin films and investigate the impact of substrate temperature during NbTiN growth. We achieve four nm thick superconducting films with a critical temperature (𝑇𝑐) of 12.3 K grown at a substrate temperature of 825 K. We demonstrate that the increased substrate temperature reduces the oxygen concentration in our films and improves the overall stoichiometry. In addition, we integrate these films with the LiNbO3 platform and investigate the obtained interface quality. Finally, we fabricate superconducting nanowire single photon detectors from the NbTiN film on LiNbO₃ and characterize the detector performance. Lastly, we report a gate-tunable Josephson diode effect in hybrid nanowire junctions consisting of a spin-orbit-coupled semiconductor core coated with epitaxial ferromagnetic insulator and superconductor shells. The wires display a hysteretic superconducting window as a function of axial magnetic field. In the superconducting regime, the devices exhibit nonreciprocal current transport, with the diode efficiency showing a strong dependence on back-gate voltage. The effect persists in a remanent magnetization state following a controlled demagnetization procedure, establishing zero-field operation. The combination of results presented in this thesis stress the importance of a material-focused approach in advancing the performance of quantum hardware. The novel hybrid material platforms developed in this thesis expand the operating regime of devices, which could enable future experiments involving gate-tunable superconductivity or topological properties. Similarly, we demonstrate that optimizing superconductor crystal structure benefits quantum devices, such as single-photon detectors and superconducting resonators.