Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Microwave Loss Characteristics of Nb Films for Quantum Computing

Bektur Abdisatarov, Bafia, D, Murthy, A, Eremeev, G, Elsayed-Ali, H E, Lee, J, Netepenko, A, Grassellino, A, Romanenko, A, Carlos, C P A, Leith, S, Guillaume Jonathan Rosaz

Published Dec 6, 2024• 0 citations
OpenAlex

Abstract

Niobium films typically constitute a significant component in the construction of modern two-dimensional superconducting qubit architectures, yet their contribution to the total decay rate is not fully understood, making it difficult to definitively identify dominant loss channels in present designs. We present the first study, which correlates direct measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radiofrequency (SRF) resonator. Our findings indicate that microwave dissipation in the HiPIMS-prepared niobium films, within the quantum regime, resembles that of record-high intrinsic quality factor of bulk niobium SRF cavities, with lifetimes extending into seconds. Microstructure and impurity level of the niobium film do not significantly affect the losses. These results set the scale of microwave losses in niobium films and show that niobium losses do not dominate the observed coherence times in present two-dimensional superconducting qubit designs, instead highlighting the role of the dielectric oxide in limiting the performance.

Related papers

Direct measurement of microwave loss in Nb films for superconducting qubits

Bektur Abdisatarov, Daniel Bafia, Akshay A. Murthy +9 more

Niobium films are a key component in modern two-dimensional superconducting qubits, yet their contribution to the total qubit decay rate is not fully understood. The presence of different layers of materials and interfaces makes it difficult to identify the dominant loss channels in present two-dimensional qubit designs. In this paper, we present the study that directly correlates measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radio frequency (SRF) resonator. By using a 3D SRF structure, we are able to isolate the niobium film loss from other contributions. Our findings indicate that microwave dissipation in the HiPIMS-prepared niobium films, within the quantum regime, resembles that of record-high intrinsic quality factor of bulk niobium SRF cavities, with lifetimes extending into seconds. Microstructure and impurity level of the niobium film do not significantly affect the losses. These results set the scale of microwave losses in niobium films and show that niobium losses do not dominate the observed coherence times in present two-dimensional superconducting qubit designs, instead highlighting the dominant role of the dielectric oxide in limiting the performance. We can also set a bound for when niobium film losses will become a limitation for qubit lifetimes.

arXiv:2407.08856•Applied Physics Letters•Sep 16, 2024•10 citations

The effect of niobium thin film structure on losses in superconducting circuits

Maxwell Drimmer, Sjoerd Telkamp, Felix L Fischer +7 more

Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.

arXiv:2403.12164•Materials for Quantum Technology•Oct 14, 2025•22 citations

Comparison of two-level system microwave losses in pure bulk microcrystalline Nb 2 O 5 and NbO 2 oxide samples

Vishal Ganesan, Jiankun Zhang, Drew G. Wild +1 more

Abstract Losses from two-level systems (TLS) associated with amorphous oxides remain one of the primary limitations to the performance of superconducting qubits and microwave cavities. Niobium resonators are widely used in quantum science experiments, yet niobium’s natural oxide layer contains various types of oxides whose relative contributions to TLS loss have not been clearly distinguished. Here, we use a superconducting 3D microwave cavity to measure commercial 99.9% trace metal pure, microcrystalline oxide powders Nb 2 O 5 and NbO 2 in bulk amounts. Using this approach, we directly compare the loss characteristics of Nb 2 O 5 and NbO 2 . Our measurements show that the nominal Nb 2 O 5 bulk oxide powder samples exhibit losses which have the power and temperature behavior expected for TLS. Moreover, the measurements agree with existing theoretical models. Analogous measurements performed on NbO 2 bulk powder samples do not show any detectable TLS loss signatures. Based on our results we propose that the TLS losses might be reduced if a high quality microcrystalline NbO 2 oxide dominates the Nb 2 O 5 oxide in practical Nb cavities. These results establish a materials based strategy for isolating oxide specific TLS losses and provide a reference measurement for niobium oxide phases relevant to superconducting quantum devices.

arXiv:2601.06668•Superconductor Science and Technology•Aug 1, 2026•0 citations

Reducing two-level systems dissipations in 3D superconducting niobium resonators by atomic layer deposition and high temperature heat treatment

Yasmine Kalboussi, Baptiste Delatte, Sarra Bira +16 more

Superconducting qubits have arisen as a leading technology platform for quantum computing, which is on the verge of revolutionizing the world's calculation capacities. Nonetheless, the fabrication of computationally reliable qubit circuits requires increasing the quantum coherence lifetimes, which are predominantly limited by the dissipations of two-level system defects present in the thin superconducting film and the adjacent dielectric regions. In this paper, we demonstrate the reduction of two-level system losses in three-dimensional superconducting radio frequency niobium resonators by atomic layer deposition of a 10 nm aluminum oxide Al2O3 thin films, followed by a high vacuum heat treatment at 650 °C for few hours. By probing the effect of several heat treatments on Al2O3-coated niobium samples by x-ray photoelectron spectroscopy plus scanning and conventional high resolution transmission electron microscopy coupled with electron energy loss spectroscopy and energy dispersive spectroscopy, we witness a dissolution of niobium native oxides and the modification of the Al2O3-Nb interface, which correlates with the enhancement of the quality factor at low fields of two 1.3 GHz niobium cavities coated with 10 nm of Al2O3.

arXiv:2402.04137•Applied Physics Letters•Mar 25, 2024•10 citations

Investigation of coherence of niobium-based resonators enabled by a fast-sealing microwave cavity

Chi Zhang, Richard Germond, Noah Janzen +3 more

Resonators and qubits with a niobium (Nb) base metal layer achieve some of the highest coherence times in superconducting quantum devices. The performance of such devices is often limited by loss associated with two-level systems, which are found primarily at material surfaces and interfaces. The metal-air (MA) interface is a major contributor to device loss. In this work, we develop a fast-sealing microwave cavity that enables devices to be placed under vacuum within five minutes of oxide removal, thereby significantly reducing the MA interface loss compared to common device processing and packaging approaches. Using coplanar stripline resonators, we demonstrate that devices sealed in such a cavity exhibit internal quality factors exceeding one million at single-photon power. After re-exposure to air, the devices show downward resonance frequency shifts and quality factor degradations, quantitatively consistent with a model of Nb oxide regrowth. The fast-sealing microwave cavity provides a practical and consistent method to mitigate MA interface loss and sustain high coherence in Nb devices, and establishes a controlled platform for studying metal oxide regrowth kinetics and dielectric properties, the understanding of which is critical to achieving high coherence in superconducting quantum devices.

quant-pharXiv:2604.08813•Apr 13, 2026•0 citations

Developing Best Practice Fabrication for Niobium Superconducting Devices

Jadrien T. Paustian

Superconducting qubits are a leading platform for scalable quantum computation. This platform offers high gate speeds and can make use of readily scalable complementary metal-oxide semiconductor (CMOS) fabrication techniques. However, superconducting qubits are susceptible to a variety of losses that arise in systems with superconductors, such as due to ubiquitous two-level systems, quasiparticles, and more. Designing fabrication processes to mitigate and manage these loss sources is critical to achieving scalable quantum computation. However, many of these loss sources are set during fabrication processing, of which there can be many different steps, each with its own parameter space. Exploring this space with qubits would be prohibitively time-consuming. Coplanar waveguide resonators provide a suitable proxy system for minimizing loss while costing less time and money to fabricate and measure. In this thesis, we explore the results of such an optimization performed on niobium resonators. Niobium is a widely used material platform for superconducting qubit circuits. We report highly consistent state-of-the-art resonator quality factors, with clear improvements over the previous fabrication recipe, and correlate the observed improvements to the internal quality factors with microstructural changes induced by hydrofluoric acid treatment, photoresist stripping, and choice of sputter deposition conditions. Additionally, we provide a detailed description of our fab process to ensure reproducibility in other lab facilities. Finally, we address some intriguing anomalies uncovered in temperature-dependent quality factors of the niobium resonators and show a correlation of the quality factors with compressive film stress.

•Dec 24, 2025•0 citations
Niobium films typically constitute a significant component in the construction of modern two-dimensional superconducting qubit architectures, yet their contribution to the total decay rate is not fully understood, making it difficult to definitively identify dominant loss channels in present designs. We present the first study, which correlates direct measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radiofrequency (SRF) resonator. Our findings indicate that microwave dissipation in the HiPIMS-prepared niobium films, within the quantum regime, resembles that of record-high intrinsic quality factor of bulk niobium SRF cavities, with lifetimes extending into seconds. Microstructure and impurity level of the niobium film do not significantly affect the losses. These results set the scale of microwave losses in niobium films and show that niobium losses do not dominate the observed coherence times in present two-dimensional superconducting qubit designs, instead highlighting the role of the dielectric oxide in limiting the performance.
Niobium films are a key component in modern two-dimensional superconducting qubits, yet their contribution to the total qubit decay rate is not fully understood. The presence of different layers of materials and interfaces makes it difficult to identify the dominant loss channels in present two-dimensional qubit designs. In this paper, we present the study that directly correlates measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radio frequency (SRF) resonator. By using a 3D SRF structure, we are able to isolate the niobium film loss from other contributions. Our findings indicate that microwave dissipation in the HiPIMS-prepared niobium films, within the quantum regime, resembles that of record-high intrinsic quality factor of bulk niobium SRF cavities, with lifetimes extending into seconds. Microstructure and impurity level of the niobium film do not significantly affect the losses. These results set the scale of microwave losses in niobium films and show that niobium losses do not dominate the observed coherence times in present two-dimensional superconducting qubit designs, instead highlighting the dominant role of the dielectric oxide in limiting the performance. We can also set a bound for when niobium film losses will become a limitation for qubit lifetimes.
Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
Abstract Losses from two-level systems (TLS) associated with amorphous oxides remain one of the primary limitations to the performance of superconducting qubits and microwave cavities. Niobium resonators are widely used in quantum science experiments, yet niobium’s natural oxide layer contains various types of oxides whose relative contributions to TLS loss have not been clearly distinguished. Here, we use a superconducting 3D microwave cavity to measure commercial 99.9% trace metal pure, microcrystalline oxide powders Nb 2 O 5 and NbO 2 in bulk amounts. Using this approach, we directly compare the loss characteristics of Nb 2 O 5 and NbO 2 . Our measurements show that the nominal Nb 2 O 5 bulk oxide powder samples exhibit losses which have the power and temperature behavior expected for TLS. Moreover, the measurements agree with existing theoretical models. Analogous measurements performed on NbO 2 bulk powder samples do not show any detectable TLS loss signatures. Based on our results we propose that the TLS losses might be reduced if a high quality microcrystalline NbO 2 oxide dominates the Nb 2 O 5 oxide in practical Nb cavities. These results establish a materials based strategy for isolating oxide specific TLS losses and provide a reference measurement for niobium oxide phases relevant to superconducting quantum devices.
Superconducting qubits have arisen as a leading technology platform for quantum computing, which is on the verge of revolutionizing the world's calculation capacities. Nonetheless, the fabrication of computationally reliable qubit circuits requires increasing the quantum coherence lifetimes, which are predominantly limited by the dissipations of two-level system defects present in the thin superconducting film and the adjacent dielectric regions. In this paper, we demonstrate the reduction of two-level system losses in three-dimensional superconducting radio frequency niobium resonators by atomic layer deposition of a 10 nm aluminum oxide Al2O3 thin films, followed by a high vacuum heat treatment at 650 °C for few hours. By probing the effect of several heat treatments on Al2O3-coated niobium samples by x-ray photoelectron spectroscopy plus scanning and conventional high resolution transmission electron microscopy coupled with electron energy loss spectroscopy and energy dispersive spectroscopy, we witness a dissolution of niobium native oxides and the modification of the Al2O3-Nb interface, which correlates with the enhancement of the quality factor at low fields of two 1.3 GHz niobium cavities coated with 10 nm of Al2O3.
Resonators and qubits with a niobium (Nb) base metal layer achieve some of the highest coherence times in superconducting quantum devices. The performance of such devices is often limited by loss associated with two-level systems, which are found primarily at material surfaces and interfaces. The metal-air (MA) interface is a major contributor to device loss. In this work, we develop a fast-sealing microwave cavity that enables devices to be placed under vacuum within five minutes of oxide removal, thereby significantly reducing the MA interface loss compared to common device processing and packaging approaches. Using coplanar stripline resonators, we demonstrate that devices sealed in such a cavity exhibit internal quality factors exceeding one million at single-photon power. After re-exposure to air, the devices show downward resonance frequency shifts and quality factor degradations, quantitatively consistent with a model of Nb oxide regrowth. The fast-sealing microwave cavity provides a practical and consistent method to mitigate MA interface loss and sustain high coherence in Nb devices, and establishes a controlled platform for studying metal oxide regrowth kinetics and dielectric properties, the understanding of which is critical to achieving high coherence in superconducting quantum devices.
Superconducting qubits are a leading platform for scalable quantum computation. This platform offers high gate speeds and can make use of readily scalable complementary metal-oxide semiconductor (CMOS) fabrication techniques. However, superconducting qubits are susceptible to a variety of losses that arise in systems with superconductors, such as due to ubiquitous two-level systems, quasiparticles, and more. Designing fabrication processes to mitigate and manage these loss sources is critical to achieving scalable quantum computation. However, many of these loss sources are set during fabrication processing, of which there can be many different steps, each with its own parameter space. Exploring this space with qubits would be prohibitively time-consuming. Coplanar waveguide resonators provide a suitable proxy system for minimizing loss while costing less time and money to fabricate and measure. In this thesis, we explore the results of such an optimization performed on niobium resonators. Niobium is a widely used material platform for superconducting qubit circuits. We report highly consistent state-of-the-art resonator quality factors, with clear improvements over the previous fabrication recipe, and correlate the observed improvements to the internal quality factors with microstructural changes induced by hydrofluoric acid treatment, photoresist stripping, and choice of sputter deposition conditions. Additionally, we provide a detailed description of our fab process to ensure reproducibility in other lab facilities. Finally, we address some intriguing anomalies uncovered in temperature-dependent quality factors of the niobium resonators and show a correlation of the quality factors with compressive film stress.