Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems

Analytical Modeling of Multiple Co-Existing Inaccuracies in RF Controlling Circuits for Superconducting Quantum Computing

Yao Tong, Quan Chen

Published Sep 4, 2023• 4 citations
Publisher

Abstract

Quantum computers based on spin qubits and superconducting qubits require radio-frequency (RF) electronic circuits to control and read out the state. As the scale of the quantum processors increases, the inaccuracy in the RF circuit becomes an increasingly significant source of nonidealities that impacts the qubit operations. In this article, we propose a closed-form model to characterize the effects of inaccuracies in the controlling RF circuits on the fidelity of single-qubit control operation of superconducting qubits. Different from previous works, our model allows characterization of multiple inaccuracies at the same time, significantly enhancing the guidance capabilities for practical quantum computing hardware design and optimization. In addition, the accuracy of the proposed model is also verified by a quantum-classical co-simulator.

DOI
10.1109/tcad.2023.3311732

Related papers

A Predictive Readout Fidelity Model Considering Nonidealities for Readout Circuit Design in Superconducting Quantum Computers

Yao Tong, Quan Chen

Superconducting quantum computing hardware relies on classical radio-frequency (RF) electronic circuits to control and measure quantum states. As the complexity of quantum computers increases, the significance of the classical circuitry component grows, necessitating the development of accurate models for its design and optimization. This study presents an analytical model that quantifies the influence of circuit nonidealities on readout fidelity in superconducting quantum computing systems. This model considers a wide range of nonidealities typically encountered in the readout chain, encompassing frequency, amplitude, phase inaccuracies, impedance mismatch, quantum noise, and amplifier noise. It further predicts the combined impact of these nonidealities on fidelity. The model’s precision and efficacy are confirmed through numerical quantum-classical co-simulation. The highest observed relative mismatch is roughly 3.5%, but most errors remain below 1%. Such a model can significantly aid in designing and optimizing practical quantum computers.

IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems•Oct 18, 2024•1 citation

Circuit models for the co-simulation of superconducting quantum computing systems

Rohith Acharya, Fahd A. Mohiyaddin, Anton Potočnik +5 more

Quantum computers based on superconducting qubits have emerged as a leading candidate for a scalable quantum processor architecture. The core of a quantum processor consists of quantum devices that are manipulated using classical electronic circuits, which need to be co-designed for optimal performance and operation. As the principles governing the behavior of the classical circuits and the quantum devices are different, this presents a unique challenge in terms of the simulation, design and optimization of the joint system. A methodology is presented to transform the behavior of small-scale quantum processors to equivalent circuit models that are usable with classical circuits in a generic electrical simulator, enabling the detailed analysis of the impact of many important non-idealities. The methodology has specifically been employed to derive a circuit model of a superconducting qubit interacting with the quantized electromagnetic field of a superconducting resonator. Based on this technique, a comprehensive analysis of the qubit operation is performed, including the coherent control and readout of the qubit using electrical signals. Furthermore, the effect of several non-idealities in the system such as qubit relaxation, decoherence and leakage out of the computational subspace are captured, in contrast to previous works. As the presented method enables the co-simulation of the control electronics with the quantum system, it facilitates the design and optimization of near-term superconducting quantum processors.

Design, Automation, and Test in Europe•Feb 1, 2021•8 citations

A co-simulation of superconducting qubit and control electronics for quantum computing

Zhanhong Jin, Shaowei Li, Xinzhe Wang +2 more

As the number of qubits in quantum computing increases, the scalability of existing qubit circuit structures and control systems may become insufficient for large-scale expansion and high-fidelity control. To address this challenge, we propose a behavioral-level model of a superconducting qubit and its control electronics, followed by a co-simulation to evaluate their performance. In this paper, we present the modeling process, simulation procedure, and resulting design specifications for the qubit control system. Our co-simulation approach utilizes MATLAB and Simulink, enabling us to derive critical circuit design specifications, such as the required Digital-to-Analog Converter (DAC) resolution, which should be 8 bits or higher, to achieve high-fidelity control. By taking into account factors such as DAC sampling rates, integral and differential nonlinearities, and filter characteristics, we optimize the control system for efficient and accurate qubit manipulation. Our model and simulation approach offer a promising solution to the scalability challenges in quantum computing, providing valuable insights for the design of large-scale superconducting quantum computing systems.

Review of Scientific Instruments•Oct 1, 2023•5 citations

High-Fidelity Control of Superconducting Qubits Using Direct Microwave Synthesis in Higher Nyquist Zones

William D. Kalfus, Diana F. Lee, Guilhem J. Ribeill +5 more

Control electronics for superconducting quantum processors have strict requirements for accurate command of the sensitive quantum states of their qubits. Hinging on the purity of ultra-phase-stable oscillators to upconvert very-low-noise baseband pulses, conventional control systems can become prohibitively complex and expensive when scaling to larger quantum devices, especially as high sampling rates become desirable for fine-grained pulse shaping. Few-gigahertz radio-frequency (RF) digital-to-analog converters (DACs) present a more economical avenue for high-fidelity control while simultaneously providing greater command over the spectrum of the synthesized signal. Modern RF DACs with extra-wide bandwidths are able to directly synthesize tones above their sampling rates, thereby keeping the system clock rate at a level compatible with modern digital logic systems while still being able to generate high-frequency pulses with arbitrary profiles. We have incorporated custom superconducting qubit control logic into off-the-shelf hardware capable of low-noise pulse synthesis up to 7.5 GHz using an RF DAC clocked at 5 GHz. Our approach enables highly linear and stable microwave synthesis over a wide bandwidth, giving rise to high-resolution control and a reduced number of required signal sources per qubit. We characterize the performance of the hardware using a five-transmon superconducting device and demonstrate consistently reduced two-qubit gate error (as low as 1.8%), which we show results from superior control chain linearity compared to traditional configurations. The exceptional flexibility and stability further establish a foundation for scalable quantum control beyond intermediate-scale devices.

arXiv:2008.02873•IEEE Transactions on Quantum Engineering•Jan 1, 2020•32 citations

Mitigating crosstalk errors for simultaneous single-qubit gates on a superconducting quantum processor

Jaap J. Wesdorp, Eric Hyyppä, Joona Andersson +61 more

Single-qubit gates on superconducting quantum processors are typically implemented using microwave pulses applied through dedicated control lines. However, these microwave pulses may also drive other qubits due to crosstalk arising from capacitive coupling and wavefunction overlap in systems with closely spaced transition frequencies. Crosstalk and frequency crowding increase errors during simultaneous single-qubit operations relative to isolated gates, thus forming a major bottleneck for scaling superconducting quantum processors. In this work, we combine model-based qubit frequency optimization with pulse shaping to demonstrate crosstalk error mitigation in single-qubit gates on a 49-qubit superconducting quantum processor. We introduce and experimentally verify an analytical model of simultaneous single-qubit gate error caused by microwave crosstalk that depends on a given pulse shape. By employing a model-based optimization strategy of qubit frequencies, we minimize the crosstalk-induced error across the processor and achieve a mean simultaneous single-qubit gate fidelity of 99.96% for a 16-ns gate duration, approaching the mean individual gate fidelity. To further reduce the simultaneous error and required qubit frequency bandwidth on high-crosstalk qubit pairs, we introduce a crosstalk transition suppression (CTS) pulse shaping technique that minimizes the spectral energy around transitions inducing leakage and crosstalk errors. Finally, we combine CTS with model-based frequency optimization across the device and experimentally show a systematic reduction in the required qubit frequency bandwidth for high-fidelity simultaneous gates, supported by simulations of systems with up to 1000 qubits. By alleviating constraints on qubit frequency bandwidth for parallel single-qubit operations, this work represents an important step for scaling towards larger quantum processors.

quant-pharXiv:2603.11018•PRX Quantum•Mar 12, 2026•15 citations

Modeling and Experimental Validation of the Intrinsic SNR in Spin Qubit Gate-Based Readout and Its Impacts on Readout Electronics

Bagas Prabowo, Jurgen Dijkema, Xiao Xue +3 more

In semiconductor spin quantum bits (qubits), the radio-frequency (RF) gate-based readout is a promising solution for future large-scale integration, as it allows for a fast, frequency-multiplexed readout architecture, enabling multiple qubits to be read out simultaneously. This paper introduces a theoretical framework to evaluate the effect of various parameters, such as the readout probe power, readout chain's noise performance, and integration time on the intrinsic readout signal-to-noise ratio (SNR), and thus readout fidelity of RF gate-based readout systems. By analyzing the underlying physics of spin qubits during readout, this work proposes a qubit readout model that takes into account the qubit's quantum mechanical properties, providing a way to evaluate the trade-offs among the aforementioned parameters. The validity of the proposed model is evaluated by comparing the simulation and experimental results. The proposed analytical approach, the developed model, and the experimental results enable designers to optimize the entire readout chain effectively, thus leading to a faster, lower-power readout system with integrated cryogenic electronics.

arXiv:2312.08993•IEEE Transactions on Quantum Engineering•Jan 1, 2024•8 citations
Quantum computers based on spin qubits and superconducting qubits require radio-frequency (RF) electronic circuits to control and read out the state. As the scale of the quantum processors increases, the inaccuracy in the RF circuit becomes an increasingly significant source of nonidealities that impacts the qubit operations. In this article, we propose a closed-form model to characterize the effects of inaccuracies in the controlling RF circuits on the fidelity of single-qubit control operation of superconducting qubits. Different from previous works, our model allows characterization of multiple inaccuracies at the same time, significantly enhancing the guidance capabilities for practical quantum computing hardware design and optimization. In addition, the accuracy of the proposed model is also verified by a quantum-classical co-simulator.
Superconducting quantum computing hardware relies on classical radio-frequency (RF) electronic circuits to control and measure quantum states. As the complexity of quantum computers increases, the significance of the classical circuitry component grows, necessitating the development of accurate models for its design and optimization. This study presents an analytical model that quantifies the influence of circuit nonidealities on readout fidelity in superconducting quantum computing systems. This model considers a wide range of nonidealities typically encountered in the readout chain, encompassing frequency, amplitude, phase inaccuracies, impedance mismatch, quantum noise, and amplifier noise. It further predicts the combined impact of these nonidealities on fidelity. The model’s precision and efficacy are confirmed through numerical quantum-classical co-simulation. The highest observed relative mismatch is roughly 3.5%, but most errors remain below 1%. Such a model can significantly aid in designing and optimizing practical quantum computers.
Quantum computers based on superconducting qubits have emerged as a leading candidate for a scalable quantum processor architecture. The core of a quantum processor consists of quantum devices that are manipulated using classical electronic circuits, which need to be co-designed for optimal performance and operation. As the principles governing the behavior of the classical circuits and the quantum devices are different, this presents a unique challenge in terms of the simulation, design and optimization of the joint system. A methodology is presented to transform the behavior of small-scale quantum processors to equivalent circuit models that are usable with classical circuits in a generic electrical simulator, enabling the detailed analysis of the impact of many important non-idealities. The methodology has specifically been employed to derive a circuit model of a superconducting qubit interacting with the quantized electromagnetic field of a superconducting resonator. Based on this technique, a comprehensive analysis of the qubit operation is performed, including the coherent control and readout of the qubit using electrical signals. Furthermore, the effect of several non-idealities in the system such as qubit relaxation, decoherence and leakage out of the computational subspace are captured, in contrast to previous works. As the presented method enables the co-simulation of the control electronics with the quantum system, it facilitates the design and optimization of near-term superconducting quantum processors.
As the number of qubits in quantum computing increases, the scalability of existing qubit circuit structures and control systems may become insufficient for large-scale expansion and high-fidelity control. To address this challenge, we propose a behavioral-level model of a superconducting qubit and its control electronics, followed by a co-simulation to evaluate their performance. In this paper, we present the modeling process, simulation procedure, and resulting design specifications for the qubit control system. Our co-simulation approach utilizes MATLAB and Simulink, enabling us to derive critical circuit design specifications, such as the required Digital-to-Analog Converter (DAC) resolution, which should be 8 bits or higher, to achieve high-fidelity control. By taking into account factors such as DAC sampling rates, integral and differential nonlinearities, and filter characteristics, we optimize the control system for efficient and accurate qubit manipulation. Our model and simulation approach offer a promising solution to the scalability challenges in quantum computing, providing valuable insights for the design of large-scale superconducting quantum computing systems.
Control electronics for superconducting quantum processors have strict requirements for accurate command of the sensitive quantum states of their qubits. Hinging on the purity of ultra-phase-stable oscillators to upconvert very-low-noise baseband pulses, conventional control systems can become prohibitively complex and expensive when scaling to larger quantum devices, especially as high sampling rates become desirable for fine-grained pulse shaping. Few-gigahertz radio-frequency (RF) digital-to-analog converters (DACs) present a more economical avenue for high-fidelity control while simultaneously providing greater command over the spectrum of the synthesized signal. Modern RF DACs with extra-wide bandwidths are able to directly synthesize tones above their sampling rates, thereby keeping the system clock rate at a level compatible with modern digital logic systems while still being able to generate high-frequency pulses with arbitrary profiles. We have incorporated custom superconducting qubit control logic into off-the-shelf hardware capable of low-noise pulse synthesis up to 7.5 GHz using an RF DAC clocked at 5 GHz. Our approach enables highly linear and stable microwave synthesis over a wide bandwidth, giving rise to high-resolution control and a reduced number of required signal sources per qubit. We characterize the performance of the hardware using a five-transmon superconducting device and demonstrate consistently reduced two-qubit gate error (as low as 1.8%), which we show results from superior control chain linearity compared to traditional configurations. The exceptional flexibility and stability further establish a foundation for scalable quantum control beyond intermediate-scale devices.
Single-qubit gates on superconducting quantum processors are typically implemented using microwave pulses applied through dedicated control lines. However, these microwave pulses may also drive other qubits due to crosstalk arising from capacitive coupling and wavefunction overlap in systems with closely spaced transition frequencies. Crosstalk and frequency crowding increase errors during simultaneous single-qubit operations relative to isolated gates, thus forming a major bottleneck for scaling superconducting quantum processors. In this work, we combine model-based qubit frequency optimization with pulse shaping to demonstrate crosstalk error mitigation in single-qubit gates on a 49-qubit superconducting quantum processor. We introduce and experimentally verify an analytical model of simultaneous single-qubit gate error caused by microwave crosstalk that depends on a given pulse shape. By employing a model-based optimization strategy of qubit frequencies, we minimize the crosstalk-induced error across the processor and achieve a mean simultaneous single-qubit gate fidelity of 99.96% for a 16-ns gate duration, approaching the mean individual gate fidelity. To further reduce the simultaneous error and required qubit frequency bandwidth on high-crosstalk qubit pairs, we introduce a crosstalk transition suppression (CTS) pulse shaping technique that minimizes the spectral energy around transitions inducing leakage and crosstalk errors. Finally, we combine CTS with model-based frequency optimization across the device and experimentally show a systematic reduction in the required qubit frequency bandwidth for high-fidelity simultaneous gates, supported by simulations of systems with up to 1000 qubits. By alleviating constraints on qubit frequency bandwidth for parallel single-qubit operations, this work represents an important step for scaling towards larger quantum processors.
In semiconductor spin quantum bits (qubits), the radio-frequency (RF) gate-based readout is a promising solution for future large-scale integration, as it allows for a fast, frequency-multiplexed readout architecture, enabling multiple qubits to be read out simultaneously. This paper introduces a theoretical framework to evaluate the effect of various parameters, such as the readout probe power, readout chain's noise performance, and integration time on the intrinsic readout signal-to-noise ratio (SNR), and thus readout fidelity of RF gate-based readout systems. By analyzing the underlying physics of spin qubits during readout, this work proposes a qubit readout model that takes into account the qubit's quantum mechanical properties, providing a way to evaluate the trade-offs among the aforementioned parameters. The validity of the proposed model is evaluated by comparing the simulation and experimental results. The proposed analytical approach, the developed model, and the experimental results enable designers to optimize the entire readout chain effectively, thus leading to a faster, lower-power readout system with integrated cryogenic electronics.