Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Physics Conference Series

Research and Design of Photoelectric Converter for Quantum Gravimeter

Mingda Zhu, Xiaoxin Liu, Yaping Wang, Jianhua Bi, Yudong Xu, Yingcong Zhu

Published Dec 1, 2022• 1 citation
Publisher

Abstract

In the control system of a quantum gravimeter, the optical signal containing phase information is weak and usually at the nV level. This situation puts forward high requirements for the measurement performance of the system. As the coupling input component of the measurement system, the noise level of the preamplifier has a dramatic influence on the noise performance. In this paper, the input current signal is provided by the photodiode. According to the photodiode output characteristics, we design three preamplifiers with different gain and bandwidth, which is verified by the optical system. Under the condition of meeting the design requirements, the noise performance is compared with the common commercial detector Model 2307. The results show that the noise performance of the photoelectric converter designed in this paper is about 1.5 times that of model 2307.

DOI
10.1088/1742-6596/2383/1/012032

Related papers

Design of Quantum Communication Broadband Amplifier Based on Photoelectric Diode

Yi Zhen Nie

according to the special requirements of quantum optics experiments, through the optimum design of broadband low noise amplifier circuit, this paper developed a broadband low noise photoelectric detector. We focus on the analysis of the factors affecting the photoelectric detector gain, bandwidth and noise, by a suitable choice of the photodiode, a sampling resistor, feedback resistor and capacitor, the broadband low noise photoelectric detector. Experiments show that, this circuit can be used for broadband low noise quantum communication circuit.

Applied Mechanics and Materials•Jul 1, 2014•0 citations

Amplification pulse signals a single-photon detector based on an avalanche photodiode

Roman Halyts, Петро Шпатар, Yurii Yaremchuk

The technology of quantum cryptography, based on the quantum properties of light, allows a random sequence of bits to be transmitted over an unprotected communication channel in such a way that an attacker's interference in the transmission process creates additional noise in the channel and is detected by legitimate users. One of the important elements of a quantum system is a single-photon detector. The closest to solving this problem is a device for recording single photons using avalanche photodiodes (APD) [1 - 6]. In this work, a scheme for amplifying current pulses flowing through a single-photon detector is proposed, using a charge-sensitive amplifier Amptek A250. The noise characteristics of the Amptek A250 amplifier are such that its contribution to detector noise is negligible. After amplification, the pulses are fed to the inputs of the comparators. The amplitude discrimination threshold of the first is selected above the level of the amplifier's own noise. The amplitude discrimination threshold of the second comparator is chosen so that the speed of pulse counting at the output of the first comparator is n times greater than at the output of the second comparator. From the outputs of the comparators, pulses are fed to the input of the microcontroller. When the microcontroller calculates a given number of N pulses, a corresponding signal for the DAC is formed at its output, which converts the digital signal into a control voltage for the power source of the avalanche photodiode. The developed device allows to increase the quantum efficiency of registration up to 48%.

International Conference on Correlation Optics•Jan 5, 2024•0 citations

Design of low-noise photodetector with a bandwidth of 130 MHz based on transimpedance amplification circuit

Jiliang Qin, Zhihui Yan, Meiru Huo +2 more

A low-noise photodetector is a basic tool for the research of quantum information processing.We present a specially designed low-noise photoelectric detector with a bandwidth of 130 MHz, using a transimpedance amplification circuit.Based on the detailed calculation of the dependence on each parameter of the detector, a useful method of how to design a low-noise and broadband photodetector is provided.When the optical power is between 1.0 and 16 mW, the photodetector has a good linear response to the injected light.Its electronics noise power is below -77 dBm, which is within the whole bandwidth.When the incident light power is 2 mW, the output noise powers are 10.0, 8.0, and 6.0 dB higher than the corresponding electronics noise within the bandwidth of 1-50, 50-90, and 90-130 MHz, respectively, which is in good agreement with the theoretical prediction.Thus, this photoelectric detector could have good application prospects in quantum communication and an optical cavity locking system.

Chinese Optics Letters•Jan 1, 2016•11 citations

Design and characterization of single photon APD detector for QKD application

Khalid A. Saeed Al-Khateeb, Nazmus Shaker Nafi, Khalid Hasan

Modeling and design of a single photon detector and its various characteristics are presented. It is a type of avalanche photo diode (APD) designed to suit the requirements of a Quantum Key Distribution (QKD) detection system. The device is modeled to operate in a gated mode at liquid nitrogen temperature for minimum noise and maximum gain. Different types of APDs are compared for best performance. The APD is part of an optical communication link, which is a private channel to transmit the key signal. The encrypted message is sent via a public channel. The optical link operates at a wavelength of 1.55μm. The design is based on InGaAs with a quantum efficiency of more than 75% and a multiplication factor of 1000. The calculated dark current is below 10-12A with an overall signal to noise ratio better than 18 dB. The device sensitivity is better than -40 dBm, which is more than an order of magnitude higher than the dark current, corresponding to a detection sensitivity of two photons in pico-second pulses.

International Conference on Computer and Communication Engineering•May 1, 2010•2 citations

Signal-to-noise ratio of preamplified homodyne detection in quantum tomography

Marcelo A. Marchiolli, Salomon Sylvain Mizrahi, V. V. Dodonov

The operational theory of homodyne detection by nonideal detectors, used in quantum tomography, was recently modified in order to incorporate the preamplification (before homodyne detection) of the input signal, thus enabling one to beat the handicap of the lower than 0.5 detector efficiency. In the present work we set expressions for the Mandel $Q$ parameter and the signal-to-noise ratio in terms of the operational (measured) moments of the preamplified homodyne detection formalism. These quantities furnish important information on the statistical properties of the input signal field and the photocounts at the output. We illustrate the theory by considering several kinds of fields (for the input signal) and determine the effects of the preamplification on the output signal-to-noise ratios. Here we essentially verify that (i) the preamplification shifts the statistics towards the super-Poissonian limit, without jeopardizing the capacity of reconstructing a sub-Poissionan input signal, and (ii) the preamplification is more effective, i.e., the rate of increase of the signal-to-noise ratio of the output photocount is larger for low-efficiency detectors than for ideal ones.

Physical Review A•May 1, 1998•9 citations

Balanced homodyne detection circuit design analysis for high gain and low noise performance

Akanksha Angural, Joyee Ghosh

The study, generation, and application of squeezed states of light has been a widely researched area in quantum optics. Vacuum fluctuations or photon shot noise quantified in terms of quadrature operators, impose a quantum limit on the sensitivity of quantum sensing and quantum communication systems. Thus, squeezing the quadratures reduces the quantum uncertainty in a particular quadrature. The amount of squeezing is, however, highly limited by the optics in the experiments and the performance of the balanced homodyne detection (BHD) systems employed for the detection of the squeezed states of light. In this paper, we have analytically studied the steady state, transient and noise responses of the balanced homodyne detection (BHD) circuitry by comparing two configurations i.e., a variable gain circuit with a differential amplifier and a current subtracting circuit with differential fine-tuning circuit (DFTC) and an adjustable bias (ABV). The current subtracting circuit design with DFTC and ABV has been adopted from Xiaoli et al. [1] in order to compensate for any differences in the photodiode performance characteristics in the two arms. A variable gain configuration is used to compensate for the unequal beam splitter ratio and uneven optical powers in the two arms. In order to further improve the noise performance of the system, a differential amplifier is used in the output of the variable gain configuration. A high transimpedance gain (~>70 dB) and a low noise (~<500nV/ √ Hz) performance can be achieved using these circuits as per our analysis.

IEEE International Conference on Emerging Electronics (ICEE)•Dec 11, 2022•0 citations
In the control system of a quantum gravimeter, the optical signal containing phase information is weak and usually at the nV level. This situation puts forward high requirements for the measurement performance of the system. As the coupling input component of the measurement system, the noise level of the preamplifier has a dramatic influence on the noise performance. In this paper, the input current signal is provided by the photodiode. According to the photodiode output characteristics, we design three preamplifiers with different gain and bandwidth, which is verified by the optical system. Under the condition of meeting the design requirements, the noise performance is compared with the common commercial detector Model 2307. The results show that the noise performance of the photoelectric converter designed in this paper is about 1.5 times that of model 2307.
according to the special requirements of quantum optics experiments, through the optimum design of broadband low noise amplifier circuit, this paper developed a broadband low noise photoelectric detector. We focus on the analysis of the factors affecting the photoelectric detector gain, bandwidth and noise, by a suitable choice of the photodiode, a sampling resistor, feedback resistor and capacitor, the broadband low noise photoelectric detector. Experiments show that, this circuit can be used for broadband low noise quantum communication circuit.
The technology of quantum cryptography, based on the quantum properties of light, allows a random sequence of bits to be transmitted over an unprotected communication channel in such a way that an attacker's interference in the transmission process creates additional noise in the channel and is detected by legitimate users. One of the important elements of a quantum system is a single-photon detector. The closest to solving this problem is a device for recording single photons using avalanche photodiodes (APD) [1 - 6]. In this work, a scheme for amplifying current pulses flowing through a single-photon detector is proposed, using a charge-sensitive amplifier Amptek A250. The noise characteristics of the Amptek A250 amplifier are such that its contribution to detector noise is negligible. After amplification, the pulses are fed to the inputs of the comparators. The amplitude discrimination threshold of the first is selected above the level of the amplifier's own noise. The amplitude discrimination threshold of the second comparator is chosen so that the speed of pulse counting at the output of the first comparator is n times greater than at the output of the second comparator. From the outputs of the comparators, pulses are fed to the input of the microcontroller. When the microcontroller calculates a given number of N pulses, a corresponding signal for the DAC is formed at its output, which converts the digital signal into a control voltage for the power source of the avalanche photodiode. The developed device allows to increase the quantum efficiency of registration up to 48%.
A low-noise photodetector is a basic tool for the research of quantum information processing.We present a specially designed low-noise photoelectric detector with a bandwidth of 130 MHz, using a transimpedance amplification circuit.Based on the detailed calculation of the dependence on each parameter of the detector, a useful method of how to design a low-noise and broadband photodetector is provided.When the optical power is between 1.0 and 16 mW, the photodetector has a good linear response to the injected light.Its electronics noise power is below -77 dBm, which is within the whole bandwidth.When the incident light power is 2 mW, the output noise powers are 10.0, 8.0, and 6.0 dB higher than the corresponding electronics noise within the bandwidth of 1-50, 50-90, and 90-130 MHz, respectively, which is in good agreement with the theoretical prediction.Thus, this photoelectric detector could have good application prospects in quantum communication and an optical cavity locking system.
Modeling and design of a single photon detector and its various characteristics are presented. It is a type of avalanche photo diode (APD) designed to suit the requirements of a Quantum Key Distribution (QKD) detection system. The device is modeled to operate in a gated mode at liquid nitrogen temperature for minimum noise and maximum gain. Different types of APDs are compared for best performance. The APD is part of an optical communication link, which is a private channel to transmit the key signal. The encrypted message is sent via a public channel. The optical link operates at a wavelength of 1.55μm. The design is based on InGaAs with a quantum efficiency of more than 75% and a multiplication factor of 1000. The calculated dark current is below 10-12A with an overall signal to noise ratio better than 18 dB. The device sensitivity is better than -40 dBm, which is more than an order of magnitude higher than the dark current, corresponding to a detection sensitivity of two photons in pico-second pulses.
The operational theory of homodyne detection by nonideal detectors, used in quantum tomography, was recently modified in order to incorporate the preamplification (before homodyne detection) of the input signal, thus enabling one to beat the handicap of the lower than 0.5 detector efficiency. In the present work we set expressions for the Mandel QQQ parameter and the signal-to-noise ratio in terms of the operational (measured) moments of the preamplified homodyne detection formalism. These quantities furnish important information on the statistical properties of the input signal field and the photocounts at the output. We illustrate the theory by considering several kinds of fields (for the input signal) and determine the effects of the preamplification on the output signal-to-noise ratios. Here we essentially verify that (i) the preamplification shifts the statistics towards the super-Poissonian limit, without jeopardizing the capacity of reconstructing a sub-Poissionan input signal, and (ii) the preamplification is more effective, i.e., the rate of increase of the signal-to-noise ratio of the output photocount is larger for low-efficiency detectors than for ideal ones.
The study, generation, and application of squeezed states of light has been a widely researched area in quantum optics. Vacuum fluctuations or photon shot noise quantified in terms of quadrature operators, impose a quantum limit on the sensitivity of quantum sensing and quantum communication systems. Thus, squeezing the quadratures reduces the quantum uncertainty in a particular quadrature. The amount of squeezing is, however, highly limited by the optics in the experiments and the performance of the balanced homodyne detection (BHD) systems employed for the detection of the squeezed states of light. In this paper, we have analytically studied the steady state, transient and noise responses of the balanced homodyne detection (BHD) circuitry by comparing two configurations i.e., a variable gain circuit with a differential amplifier and a current subtracting circuit with differential fine-tuning circuit (DFTC) and an adjustable bias (ABV). The current subtracting circuit design with DFTC and ABV has been adopted from Xiaoli et al. [1] in order to compensate for any differences in the photodiode performance characteristics in the two arms. A variable gain configuration is used to compensate for the unequal beam splitter ratio and uneven optical powers in the two arms. In order to further improve the noise performance of the system, a differential amplifier is used in the output of the variable gain configuration. A high transimpedance gain (~>70 dB) and a low noise (~<500nV/ √ Hz) performance can be achieved using these circuits as per our analysis.