Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chinese Optics Letters

Design of low-noise photodetector with a bandwidth of 130 MHz based on transimpedance amplification circuit

Jiliang Qin, Zhihui Yan, Meiru Huo, Xiaojun Jia, and Kunchi Peng and Kunchi Peng

Published Jan 1, 2016• 11 citations
Publisher

Abstract

A low-noise photodetector is a basic tool for the research of quantum information processing.We present a specially designed low-noise photoelectric detector with a bandwidth of 130 MHz, using a transimpedance amplification circuit.Based on the detailed calculation of the dependence on each parameter of the detector, a useful method of how to design a low-noise and broadband photodetector is provided.When the optical power is between 1.0 and 16 mW, the photodetector has a good linear response to the injected light.Its electronics noise power is below -77 dBm, which is within the whole bandwidth.When the incident light power is 2 mW, the output noise powers are 10.0, 8.0, and 6.0 dB higher than the corresponding electronics noise within the bandwidth of 1-50, 50-90, and 90-130 MHz, respectively, which is in good agreement with the theoretical prediction.Thus, this photoelectric detector could have good application prospects in quantum communication and an optical cavity locking system.

DOI
10.3788/col201614.122701

Related papers

500 MHz resonant photodetector for high-quantum-efficiency, low-noise homodyne measurement

Takahiro Serikawa, Akira Furusawa

We design and demonstrate a resonant-type differential photodetector for a low-noise quantum homodyne measurement at 500 MHz optical sideband with 17 MHz of bandwidth. By using a microwave monolithic amplifier and a discrete voltage buffer circuit, a low-noise voltage amplifier is realized and applied to our detector. 12 dB of signal-to-noise ratio of the shot noise to the electric noise is obtained with 5 mW of a continuous-wave local oscillator. We analyze the frequency response and the noise characteristics of a resonant photodetector, and the theoretical model agrees with the shot noise measurement.

arXiv:1803.06462•Review of Scientific Instruments•Jun 1, 2018•25 citations

Design of Quantum Communication Broadband Amplifier Based on Photoelectric Diode

Yi Zhen Nie

according to the special requirements of quantum optics experiments, through the optimum design of broadband low noise amplifier circuit, this paper developed a broadband low noise photoelectric detector. We focus on the analysis of the factors affecting the photoelectric detector gain, bandwidth and noise, by a suitable choice of the photodiode, a sampling resistor, feedback resistor and capacitor, the broadband low noise photoelectric detector. Experiments show that, this circuit can be used for broadband low noise quantum communication circuit.

Applied Mechanics and Materials•Jul 1, 2014•0 citations

Low-noise,Broadband Photo-detector Designs in Quantum Optics

Kuanshou Zhang

We report a kind of low-noise,broadband photo-detector that can be applied in the quantum optics experiments.Based on the proper photo-diode,sampling resistor,feedback resistor and capacity were selected,a low-noise,broadband photo-detector was designed and fabricated.The photo-detector can be used to detect the quantum noise with the band-width of 2-50 MHz and the incident power of up to 15 mW.It can also be applied in the quantum optics experiments such as balance detectors,homodyne detectors and so on.A pair of identical photo-detectors with the band-width of 2-31 MHz and Common Mode Rejection Ratio of 30 dB was used as balance detectors to measure the intensity noise of white light,cw single frequency 1064 nm laser and 1550 nm laser.

Acta Sinica Quantum Optica•Jan 1, 2010•2 citations

Stabilization improvement of the squeezed optical fields using a high signal-to-noise ratio bootstrap photodetector

Xiaoli Wang, Liang Wu, Shaocong Liang +6 more

High-precision cavity locking is crucial for squeezing optical fields. Here, a bootstrapped low-noise photodetector is utilized in the generation process of the squeezed state of light. This process is based on a combination of a modified trans-impedance amplifier (TIA) circuit and a two-stage bootstrap amplifier circuit. This not only achieves high-precision and long-term stable locking of the optical cavity, but it also improves the degree to which the light field is squeezed. The experiment results show that the detector has a high signal-to-noise ratio (SNR) of 26.7 dB at the analysis frequency of 3 MHz when measuring the shot noise with an injection optical power of 800 µW, and the equivalent optical power noise level is lower than 2.4 pW/Hz in the frequency range of 1-30 MHz. Moreover, the squeezing degree of the quadrature amplitude squeezed state light field can be improved by more than 34.9% when the detector is used for optical cavity locking. The photodetector is useful in continuous variable (CV) quantum information research.

Optics Express•Dec 5, 2022•5 citations

An ultra-sensitive balanced detector with low noise for continuous-variable quantum key distribution

Qi-Ming Lu, Qi Shen, Yuan Cao +2 more

A well-balanced detector with high sensitivity and low noise is presented in this paper. The two-stage amplification structure is used to increase electronic gain while keeping an effective bandwidth of about 70 MHz. In order to further reduce electronic noise, a junction field-effect transistor(JFET) is connected between photodiodes and transimpedance amplifier to reduce the impact of amplifier leakage current. Benefit from these designs, the root-mean-square(RMS) of noise voltage is about 6 mV with a gain of 3.2E5 V/W, and it means an ultra-low noise equivalent power density of 2.2E-12 W/rtHz, only half of common low-noise commercial detectors. In addition, two photodiodes in similar frequency response are selected for detector and make the common mode rejection ratio(CMRR) of detector reached 53 dB, about 13 dB higher than commercial detectors. Further tests indicate that 16.8 dB shot-noise to electronic-noise ratio is measured in our detector, which is better than most high speed balanced detectors.

arXiv:1806.03394•Jun 9, 2018•2 citations

High-power quantum-limited 35 MHz photodiode and classical laser noise suppression

Vincent Dumont, Jiaxing Ma, Eamon Egan +1 more

To benefit high-power interferometry and the creation of low-noise light sources, we develop a simple lead-compensated photodetector enabling quantum-limited readout from 0.3 to 10 mW and 10 kΩ gain from 85 Hz to 35 MHz, with a noise equivalent power of 9 pW/Hz. Feeding the detector output back to an intensity modulator, we suppress the classical amplitude noise of a commercial 1550 nm fiber laser to the shot noise limit over a bandwidth of 700 Hz-200 kHz, observing no degradation to its (nominally ∼100 Hz) linewidth.

arXiv:2308.02476•Review of Scientific Instruments•Dec 1, 2023•2 citations
A low-noise photodetector is a basic tool for the research of quantum information processing.We present a specially designed low-noise photoelectric detector with a bandwidth of 130 MHz, using a transimpedance amplification circuit.Based on the detailed calculation of the dependence on each parameter of the detector, a useful method of how to design a low-noise and broadband photodetector is provided.When the optical power is between 1.0 and 16 mW, the photodetector has a good linear response to the injected light.Its electronics noise power is below -77 dBm, which is within the whole bandwidth.When the incident light power is 2 mW, the output noise powers are 10.0, 8.0, and 6.0 dB higher than the corresponding electronics noise within the bandwidth of 1-50, 50-90, and 90-130 MHz, respectively, which is in good agreement with the theoretical prediction.Thus, this photoelectric detector could have good application prospects in quantum communication and an optical cavity locking system.
We design and demonstrate a resonant-type differential photodetector for a low-noise quantum homodyne measurement at 500 MHz optical sideband with 17 MHz of bandwidth. By using a microwave monolithic amplifier and a discrete voltage buffer circuit, a low-noise voltage amplifier is realized and applied to our detector. 12 dB of signal-to-noise ratio of the shot noise to the electric noise is obtained with 5 mW of a continuous-wave local oscillator. We analyze the frequency response and the noise characteristics of a resonant photodetector, and the theoretical model agrees with the shot noise measurement.
according to the special requirements of quantum optics experiments, through the optimum design of broadband low noise amplifier circuit, this paper developed a broadband low noise photoelectric detector. We focus on the analysis of the factors affecting the photoelectric detector gain, bandwidth and noise, by a suitable choice of the photodiode, a sampling resistor, feedback resistor and capacitor, the broadband low noise photoelectric detector. Experiments show that, this circuit can be used for broadband low noise quantum communication circuit.
We report a kind of low-noise,broadband photo-detector that can be applied in the quantum optics experiments.Based on the proper photo-diode,sampling resistor,feedback resistor and capacity were selected,a low-noise,broadband photo-detector was designed and fabricated.The photo-detector can be used to detect the quantum noise with the band-width of 2-50 MHz and the incident power of up to 15 mW.It can also be applied in the quantum optics experiments such as balance detectors,homodyne detectors and so on.A pair of identical photo-detectors with the band-width of 2-31 MHz and Common Mode Rejection Ratio of 30 dB was used as balance detectors to measure the intensity noise of white light,cw single frequency 1064 nm laser and 1550 nm laser.
High-precision cavity locking is crucial for squeezing optical fields. Here, a bootstrapped low-noise photodetector is utilized in the generation process of the squeezed state of light. This process is based on a combination of a modified trans-impedance amplifier (TIA) circuit and a two-stage bootstrap amplifier circuit. This not only achieves high-precision and long-term stable locking of the optical cavity, but it also improves the degree to which the light field is squeezed. The experiment results show that the detector has a high signal-to-noise ratio (SNR) of 26.7 dB at the analysis frequency of 3 MHz when measuring the shot noise with an injection optical power of 800 µW, and the equivalent optical power noise level is lower than 2.4 pW/Hz in the frequency range of 1-30 MHz. Moreover, the squeezing degree of the quadrature amplitude squeezed state light field can be improved by more than 34.9% when the detector is used for optical cavity locking. The photodetector is useful in continuous variable (CV) quantum information research.
A well-balanced detector with high sensitivity and low noise is presented in this paper. The two-stage amplification structure is used to increase electronic gain while keeping an effective bandwidth of about 70 MHz. In order to further reduce electronic noise, a junction field-effect transistor(JFET) is connected between photodiodes and transimpedance amplifier to reduce the impact of amplifier leakage current. Benefit from these designs, the root-mean-square(RMS) of noise voltage is about 6 mV with a gain of 3.2E5 V/W, and it means an ultra-low noise equivalent power density of 2.2E-12 W/rtHz, only half of common low-noise commercial detectors. In addition, two photodiodes in similar frequency response are selected for detector and make the common mode rejection ratio(CMRR) of detector reached 53 dB, about 13 dB higher than commercial detectors. Further tests indicate that 16.8 dB shot-noise to electronic-noise ratio is measured in our detector, which is better than most high speed balanced detectors.
To benefit high-power interferometry and the creation of low-noise light sources, we develop a simple lead-compensated photodetector enabling quantum-limited readout from 0.3 to 10 mW and 10 kΩ gain from 85 Hz to 35 MHz, with a noise equivalent power of 9 pW/Hz. Feeding the detector output back to an intensity modulator, we suppress the classical amplitude noise of a commercial 1550 nm fiber laser to the shot noise limit over a bandwidth of 700 Hz-200 kHz, observing no degradation to its (nominally ∼100 Hz) linewidth.