Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Measurements of an RSFQ digital SQUID system

Pascal Febvre

Published Apr 6, 2009• 0 citations
OpenAlex

Related papers

Design and Optimization of Fully Digital SQUID Based on Bi-Directional RSFQ

Farshad Foroughi, Ali Bozbey, Mehdi Fardmanesh

Journal of Superconductivity and Novel Magnetism•Feb 6, 2014•6 citations

Design and Operation of RSFQ Distributed Output Amplifier Equipped with double-stack SQUIDs

Komei Higuchi, Hiroshi Shimada, Yoshinao Mizugaki

IEICE Technical Report; IEICE Tech. Rep.•Aug 2, 2019•0 citations

Bit error rate measurements on RSFQ circuits using a SQUID current comparator

Masaaki Maezawa, Fuminori Hirayama, Motohiro Suzuki

We propose a simple method of measuring bit error rates (BERs) for rapid single flux quantum (RSFQ) circuits operating at high frequencies. An error detector based on a SQUID current comparator, which operates without a timing clock, is employed to simplify the test system and measurements. We successfully investigated high-frequency operation of RSFQ cells that were utilized to implement our RSFQ digital-to-analogue converter for metrology applications. Sufficiently low BERs were demonstrated in the circuit operation at several tens of gigahertz.

Superconductor Science and Technology•Mar 16, 2006•0 citations

High-sensitivity DC-SQUID measurements

Pasquale Carelli, Maria Gabriella Castellano

Physica B Condensed Matter•May 1, 2000•6 citations

Investigation of the design of a digital SQUID sensor

Friedrich Uhlmann, St Lange, M. Khabipov +1 more

Physica C Superconductivity•Nov 1, 1999•7 citations

Design of an RSFQ control circuit to observe MQC on an rf-SQUID

Roberto Rey-de-Castro, Mark F. Bocko, Andrea M. Herr +2 more

We believe that the best chance to observe macroscopic quantum coherence (MQC) in an rf-SQUID qubit is to use on-chip RSFQ digital circuits for preparing, evolving and reading out the qubit's quantum state. This approach allows experiments to be conducted on a very short time scale (sub-nanosecond) without the use of large bandwidth control lines that would couple environmental degrees of freedom to the qubit, thus contributing to its decoherence. In this paper we present our design of an RSFQ digital control circuit for demonstrating MQC in an rf-SQUID. We assess some of the key practical issues in the circuit design including the achievement of the necessary flux bias stability. We present an "active" isolation structure to be used to increase coherence times. The structure decouples the SQUID from external degrees of freedom, and then couples it to the output measurement circuitry when required, all under the active control of RSFQ circuits.

arXiv:quant-ph/0102089•IEEE Transactions on Applied Superconductivity•Mar 1, 2001•24 citations
We propose a simple method of measuring bit error rates (BERs) for rapid single flux quantum (RSFQ) circuits operating at high frequencies. An error detector based on a SQUID current comparator, which operates without a timing clock, is employed to simplify the test system and measurements. We successfully investigated high-frequency operation of RSFQ cells that were utilized to implement our RSFQ digital-to-analogue converter for metrology applications. Sufficiently low BERs were demonstrated in the circuit operation at several tens of gigahertz.
We believe that the best chance to observe macroscopic quantum coherence (MQC) in an rf-SQUID qubit is to use on-chip RSFQ digital circuits for preparing, evolving and reading out the qubit's quantum state. This approach allows experiments to be conducted on a very short time scale (sub-nanosecond) without the use of large bandwidth control lines that would couple environmental degrees of freedom to the qubit, thus contributing to its decoherence. In this paper we present our design of an RSFQ digital control circuit for demonstrating MQC in an rf-SQUID. We assess some of the key practical issues in the circuit design including the achievement of the necessary flux bias stability. We present an "active" isolation structure to be used to increase coherence times. The structure decouples the SQUID from external degrees of freedom, and then couples it to the output measurement circuitry when required, all under the active control of RSFQ circuits.