Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Superconductivity and Novel Magnetism

Design and Optimization of Fully Digital SQUID Based on Bi-Directional RSFQ

Farshad Foroughi, Ali Bozbey, Mehdi Fardmanesh

Published Feb 6, 2014• 6 citations
Publisher
DOI
10.1007/s10948-014-2501-8

Related papers

Measurements of an RSFQ digital SQUID system

Pascal Febvre

•Apr 6, 2009•0 citations

Design and Operation of RSFQ Distributed Output Amplifier Equipped with double-stack SQUIDs

Komei Higuchi, Hiroshi Shimada, Yoshinao Mizugaki

IEICE Technical Report; IEICE Tech. Rep.•Aug 2, 2019•0 citations

Design of an RSFQ control circuit to observe MQC on an rf-SQUID

Roberto Rey-de-Castro, Mark F. Bocko, Andrea M. Herr +2 more

We believe that the best chance to observe macroscopic quantum coherence (MQC) in an rf-SQUID qubit is to use on-chip RSFQ digital circuits for preparing, evolving and reading out the qubit's quantum state. This approach allows experiments to be conducted on a very short time scale (sub-nanosecond) without the use of large bandwidth control lines that would couple environmental degrees of freedom to the qubit, thus contributing to its decoherence. In this paper we present our design of an RSFQ digital control circuit for demonstrating MQC in an rf-SQUID. We assess some of the key practical issues in the circuit design including the achievement of the necessary flux bias stability. We present an "active" isolation structure to be used to increase coherence times. The structure decouples the SQUID from external degrees of freedom, and then couples it to the output measurement circuitry when required, all under the active control of RSFQ circuits.

arXiv:quant-ph/0102089•IEEE Transactions on Applied Superconductivity•Mar 1, 2001•24 citations

RSFQ: What we know and what we don't

Stanislav V. Polonsky

Rapid Single Flux Quantum (RSFQ) Josephson-junction technology is capable of processing digital data at sub-terahertz frequencies while dissipating almost negligible power. At the present time one can routinely simulate, optimize, design, manufacture, and test an elementary RSFQ logic/memory cell consisting of dozens of Josephson junctions. Furthermore, a number of relatively complex (few hundred to few thousand Josephson junctions) digital circuits were designed and successfully tested. Moreover we know how to implement several RSFQ systems (including analog-to-digital and digital-to-analog converters, digital SQUIDs for supersensitive magnetometry, and digital autocorrelator for radioastronomy) which would far outperform their currently available and even prospective semiconductor counterparts. In order to implement more complex RSFQ systems, including high-performance digital signal processors and general purpose computers there are a number of technical problems to solve. The issues include making full use of on-chip sub-terahertz processing in conditions when inter-chip data/clock exchange speed is bound by bandwidth of the order of a few Gbps/pin. I present the current know-how of the field, and formulate the questions that need to be solved before the RSFQ technology becomes a major workhorse of high-performance computation.

IEEE International Conference on Computer Design: VLSI in Computers and Processors (ICCD)•Dec 24, 2002•1 citation

Investigation of the design of a digital SQUID sensor

Friedrich Uhlmann, St Lange, M. Khabipov +1 more

Physica C Superconductivity•Nov 1, 1999•7 citations

Error Detection Method for RSFQ Voltage Multipliers Using a SQUID Detector

Fuminori Hirayama, Masaaki Maezawa, Motohiro Suzuki +1 more

The voltage multiplier (VM) is a principal component in high-precision digital-to-analog (D/A) converters based on rapid single flux quantum (RSFQ) circuits. Experimental confirmation of correct operation of the VM is important to guarantee the accuracy of the D/A converter. In this study, a circuit for direct comparison of the output voltages of VMs was designed and demonstrated. An on-chip SQUID sensor was utilized to detect the VM errors. Bit error rates of a single-stage VM were successfully measured down to 10/sup -12/ in the constant-voltage regions. A method of detecting errors during transients was also proposed and carried out.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•1 citation
We believe that the best chance to observe macroscopic quantum coherence (MQC) in an rf-SQUID qubit is to use on-chip RSFQ digital circuits for preparing, evolving and reading out the qubit's quantum state. This approach allows experiments to be conducted on a very short time scale (sub-nanosecond) without the use of large bandwidth control lines that would couple environmental degrees of freedom to the qubit, thus contributing to its decoherence. In this paper we present our design of an RSFQ digital control circuit for demonstrating MQC in an rf-SQUID. We assess some of the key practical issues in the circuit design including the achievement of the necessary flux bias stability. We present an "active" isolation structure to be used to increase coherence times. The structure decouples the SQUID from external degrees of freedom, and then couples it to the output measurement circuitry when required, all under the active control of RSFQ circuits.
Rapid Single Flux Quantum (RSFQ) Josephson-junction technology is capable of processing digital data at sub-terahertz frequencies while dissipating almost negligible power. At the present time one can routinely simulate, optimize, design, manufacture, and test an elementary RSFQ logic/memory cell consisting of dozens of Josephson junctions. Furthermore, a number of relatively complex (few hundred to few thousand Josephson junctions) digital circuits were designed and successfully tested. Moreover we know how to implement several RSFQ systems (including analog-to-digital and digital-to-analog converters, digital SQUIDs for supersensitive magnetometry, and digital autocorrelator for radioastronomy) which would far outperform their currently available and even prospective semiconductor counterparts. In order to implement more complex RSFQ systems, including high-performance digital signal processors and general purpose computers there are a number of technical problems to solve. The issues include making full use of on-chip sub-terahertz processing in conditions when inter-chip data/clock exchange speed is bound by bandwidth of the order of a few Gbps/pin. I present the current know-how of the field, and formulate the questions that need to be solved before the RSFQ technology becomes a major workhorse of high-performance computation.
The voltage multiplier (VM) is a principal component in high-precision digital-to-analog (D/A) converters based on rapid single flux quantum (RSFQ) circuits. Experimental confirmation of correct operation of the VM is important to guarantee the accuracy of the D/A converter. In this study, a circuit for direct comparison of the output voltages of VMs was designed and demonstrated. An on-chip SQUID sensor was utilized to detect the VM errors. Bit error rates of a single-stage VM were successfully measured down to 10/sup -12/ in the constant-voltage regions. A method of detecting errors during transients was also proposed and carried out.