Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Active impedance matching of a cryogenic radio frequency resonator for ion traps

M. Schubert, L. Kilzer, T. Dubielzig, Meinhard Schilling, C. Ospelkaus, Benedikt Hampel

Published Sep 1, 2022• 3 citations
Publisher

Abstract

A combination of direct current (DC) fields and high amplitude radio frequency (RF) fields is necessary to trap ions in a Paul trap. Such high electric RF fields are usually reached with the help of a resonator in close proximity to the ion trap. Ion trap based quantum computers profit from good vacuum conditions and low heating rates that cryogenic environments provide. However, an impedance matching network between the resonator and its RF source is necessary, as an unmatched resonator would require higher input power due to power reflection. The reflected power would not contribute to the RF trapping potential, and the losses in the cable induce additional heat into the system. The electrical properties of the matching network components change during cooling, and a cryogenic setup usually prohibits physical access to integrated components while the experiment is running. This circumstance leads to either several cooling cycles to improve the matching at cryogenic temperatures or the operation of poorly matched resonators. In this work, we demonstrate an RF resonator that is actively matched to the wave impedance of coaxial cables and the signal source. The active part of the matching circuit consists of a varactor diode array. Its capacitance depends on the DC voltage applied from outside the cryostat. We present measurements of the power reflection, the Q-factor, and higher harmonic signals resulting from the nonlinearity of the varactor diodes. The RF resonator is tested in a cryostat at room temperature and cryogenic temperatures, down to 4.3 K. A superior impedance matching for different ion traps can be achieved with this type of resonator.

DOI
10.1063/5.0097583

Related papers

Cryogenic resonator design for trapped ion experiments in Paul traps

Matthias F. Brandl, Philipp Schindler, Thomas Monz +1 more

Trapping ions in Paul traps require high radio frequency voltages, which are generated using resonators. When operating traps in a cryogenic environment, an in-vacuum resonator showing low loss is crucial to limit the thermal load to the cryostat. In this study, we present a guide for the design and production of compact, shielded cryogenic resonators. We produced and characterized three different types of resonators and furthermore demonstrate efficient impedance matching of these resonators at cryogenic temperatures.

arXiv:1601.06699•Applied Physics B•May 18, 2016•13 citations

Superconducting NbTi Radiofrequency Resonator for Surface ion Traps

M. Schubert, D. Fegelein, Dominik Hanisch +3 more

Trapped-ion qubits are one approach among many for achieving scalable quantum computers. An ion trap has to be operated with several dc and radio frequency (rf) signals to trap and control its qubits. Many ion trap setups are operated at cryogenic temperatures to reduce thermal influences, to reach very high vacuum, and to achieve high fidelity for quantum operations. A resonance circuit, consisting of a coil and the capacitance of the trap electrodes, is used to step-up a low power rf signal to high amplitudes in close proximity to the ion trap. These ac fields are used to confine ions$70 \,{\rm \mu }\mathrm{m}$above a surface ion trap chip. An increased quality factor (Q-factor) of the resonance circuit leads to a higher voltage gain, but the experiment also benefits from a better attenuation of parasitic frequency components in the confining electric field. The Q-factor is inversely proportional to the trap capacitance. Since ion traps are growing in size due to a larger number of qubits, the capacitance is increasing. Therefore, the development of a coil with low losses becomes even more important. In this work, we present the setup of a superconducting coil for a high-Q resonator, measurements of the Q-factor, and its temperature dependency. The coil is made of a niobium-titanium (NbTi) wire wound on a threaded bobbin made of ceramics and equipped with further thermalization structures. The superconducting resonator is a very promising approach to satisfy the needs for future trapped-ion quantum computing setups.

IEEE Transactions on Applied Superconductivity•Jan 8, 2024•0 citations

Compact radio-frequency resonator for cryogenic ion traps

Davide Gandolfi, M. Niedermayr, M. Kumph +2 more

We report on the investigation and implementation of a lumped-component, radio-frequency resonator used in a cryogenic vacuum environment to drive an ion trap. The resonator was required to achieve the voltages necessary to trap (~100 V), while dissipating very little power. Ultimately, for an input voltage of 1.35 V, a voltage gain of 100 was measured at 5.7 K, using a design which dissipated only 18 mW. The resonator operated at a frequency of 7.64 MHz and had a Q of 700. Single (40)Ca(+) ions were confined in a trap driven by this device, providing proof of successful resonator operation at low temperature.

arXiv:1204.5004•Review of Scientific Instruments•Aug 1, 2012•25 citations

Design and fabrication of ion traps for low RF power dissipation

Jonathan David Sterk, Matthew G. Blain, Matthew A. Delaney +13 more

Large surface-electrode ion traps with multiple trapping regions and junctions are a natural approach to scaling trapped ion quantum computers, supporting the connectivity and ion counts necessary for complex quantum algorithms. However, a major hurdle in this scaling is on-chip power dissipation from the applied RF voltage, which increases at a rate between linear and cubic relative to trap size, depending on whether the losses are dielectric or Ohmic. Here, we present two versions of a trap with features designed to reduce both types of RF power dissipation. The first variant contains a raised RF electrode that increases the electrode–ground distance to reduce capacitance. Different DC voltage sources are demonstrated on this trap to show that technical noise before the filter remains the dominant source of voltage noise and therefore motional heating. The second variant additionally includes a method for removing dielectric from beneath the RF electrode to further reduce dielectric losses. These traps were demonstrated at room temperature with 40Ca+ ions. The similar heating rates and heating rate axial frequency dependencies between 2.4 and 3.0 MHz illustrate that this dielectric modification is not detrimental to trap performance.

AVS Quantum Science•Jun 1, 2026•1 citation

Cryogenic surface electrode ion traps with integrated superconducting microwave resonators for polar molecular ion spectroscopy

Paul Antohi

Trapped cold molecules open the possibility of studying ultracold chemistry and astrophysical processes in laboratory settings. Their rich internal structure also makes them suitable for quantum information manipulation or for tests of fundamental laws of nature. These experiments require precise control over the molecular internal degrees of freedom. There are few present proposals for trapping and cooling molecules. One proposal is based on confining neutral polar molecules in DC Stark shift traps, but this approach presents some issues. An attractive alternative is to confine polar molecular ions in RF Paul ion traps, which is the focus of this thesis. The objectives here are to develop the theoretical models and to devise the experimental components and methods to investigate the coupling of polar molecular ions' rotational states to the microwave radiation. The new approach presented here is based on co-trapping Sr+ atomic ions together with SrCl+ molecular ions in a cryogenic surface electrode RF ion trap and on using the coupling of the molecular ion's rotational states to an integrated superconducting microwave line or cavity either as a cooling method or for precise rotational spectroscopy. The first part of the thesis describes two theoretical methods for observing the coupling of the microwave radiation to the rotational levels of a molecule. The first method proposed is based on the enhancement of the molecular rotational transition rates by the co-trapped molecular-atomic ions Coulomb collisions. The second method is based on microwave cavity assisted heating or cooling of the molecular ions. The second part of the thesis presents the development of a cryogenic surface electrode RF ion trap with an integrated microwave transmission line/resonator. The ion trap is operated in a 4.2 K closed cycle cryostat.

•Jan 1, 2011•1 citation

An ultralow-noise superconducting radio-frequency ion trap for frequency metrology with highly charged ions

Julian Stark, Christian Warnecke, S. Bogen +17 more

We present a novel ultrastable superconducting radio-frequency (RF) ion trap realized as a combination of an RF cavity and a linear Paul trap. Its RF quadrupole mode at 34.52 MHz reaches a quality factor of Q ≈ 2.3 × 105 at a temperature of 4.1 K and is used to radially confine ions in an ultralow-noise pseudopotential. This concept is expected to strongly suppress motional heating rates and related frequency shifts that limit the ultimate accuracy achieved in advanced ion traps for frequency metrology. Running with its low-vibration cryogenic cooling system, electron-beam ion trap, and deceleration beamline supplying highly charged ions (HCIs), the superconducting trap offers ideal conditions for optical frequency metrology with ionic species. We report its proof-of-principle operation as a quadrupole-mass filter with HCIs and trapping of Doppler-cooled 9Be+ Coulomb crystals.

arXiv:2102.02793•Review of Scientific Instruments•Aug 1, 2021•8 citations
A combination of direct current (DC) fields and high amplitude radio frequency (RF) fields is necessary to trap ions in a Paul trap. Such high electric RF fields are usually reached with the help of a resonator in close proximity to the ion trap. Ion trap based quantum computers profit from good vacuum conditions and low heating rates that cryogenic environments provide. However, an impedance matching network between the resonator and its RF source is necessary, as an unmatched resonator would require higher input power due to power reflection. The reflected power would not contribute to the RF trapping potential, and the losses in the cable induce additional heat into the system. The electrical properties of the matching network components change during cooling, and a cryogenic setup usually prohibits physical access to integrated components while the experiment is running. This circumstance leads to either several cooling cycles to improve the matching at cryogenic temperatures or the operation of poorly matched resonators. In this work, we demonstrate an RF resonator that is actively matched to the wave impedance of coaxial cables and the signal source. The active part of the matching circuit consists of a varactor diode array. Its capacitance depends on the DC voltage applied from outside the cryostat. We present measurements of the power reflection, the Q-factor, and higher harmonic signals resulting from the nonlinearity of the varactor diodes. The RF resonator is tested in a cryostat at room temperature and cryogenic temperatures, down to 4.3 K. A superior impedance matching for different ion traps can be achieved with this type of resonator.
Trapping ions in Paul traps require high radio frequency voltages, which are generated using resonators. When operating traps in a cryogenic environment, an in-vacuum resonator showing low loss is crucial to limit the thermal load to the cryostat. In this study, we present a guide for the design and production of compact, shielded cryogenic resonators. We produced and characterized three different types of resonators and furthermore demonstrate efficient impedance matching of these resonators at cryogenic temperatures.
Trapped-ion qubits are one approach among many for achieving scalable quantum computers. An ion trap has to be operated with several dc and radio frequency (rf) signals to trap and control its qubits. Many ion trap setups are operated at cryogenic temperatures to reduce thermal influences, to reach very high vacuum, and to achieve high fidelity for quantum operations. A resonance circuit, consisting of a coil and the capacitance of the trap electrodes, is used to step-up a low power rf signal to high amplitudes in close proximity to the ion trap. These ac fields are used to confine ions70 μm70 \,{\rm \mu }\mathrm{m}70μmabove a surface ion trap chip. An increased quality factor (Q-factor) of the resonance circuit leads to a higher voltage gain, but the experiment also benefits from a better attenuation of parasitic frequency components in the confining electric field. The Q-factor is inversely proportional to the trap capacitance. Since ion traps are growing in size due to a larger number of qubits, the capacitance is increasing. Therefore, the development of a coil with low losses becomes even more important. In this work, we present the setup of a superconducting coil for a high-Q resonator, measurements of the Q-factor, and its temperature dependency. The coil is made of a niobium-titanium (NbTi) wire wound on a threaded bobbin made of ceramics and equipped with further thermalization structures. The superconducting resonator is a very promising approach to satisfy the needs for future trapped-ion quantum computing setups.
We report on the investigation and implementation of a lumped-component, radio-frequency resonator used in a cryogenic vacuum environment to drive an ion trap. The resonator was required to achieve the voltages necessary to trap (~100 V), while dissipating very little power. Ultimately, for an input voltage of 1.35 V, a voltage gain of 100 was measured at 5.7 K, using a design which dissipated only 18 mW. The resonator operated at a frequency of 7.64 MHz and had a Q of 700. Single (40)Ca(+) ions were confined in a trap driven by this device, providing proof of successful resonator operation at low temperature.
Large surface-electrode ion traps with multiple trapping regions and junctions are a natural approach to scaling trapped ion quantum computers, supporting the connectivity and ion counts necessary for complex quantum algorithms. However, a major hurdle in this scaling is on-chip power dissipation from the applied RF voltage, which increases at a rate between linear and cubic relative to trap size, depending on whether the losses are dielectric or Ohmic. Here, we present two versions of a trap with features designed to reduce both types of RF power dissipation. The first variant contains a raised RF electrode that increases the electrode–ground distance to reduce capacitance. Different DC voltage sources are demonstrated on this trap to show that technical noise before the filter remains the dominant source of voltage noise and therefore motional heating. The second variant additionally includes a method for removing dielectric from beneath the RF electrode to further reduce dielectric losses. These traps were demonstrated at room temperature with 40Ca+ ions. The similar heating rates and heating rate axial frequency dependencies between 2.4 and 3.0 MHz illustrate that this dielectric modification is not detrimental to trap performance.
Trapped cold molecules open the possibility of studying ultracold chemistry and astrophysical processes in laboratory settings. Their rich internal structure also makes them suitable for quantum information manipulation or for tests of fundamental laws of nature. These experiments require precise control over the molecular internal degrees of freedom. There are few present proposals for trapping and cooling molecules. One proposal is based on confining neutral polar molecules in DC Stark shift traps, but this approach presents some issues. An attractive alternative is to confine polar molecular ions in RF Paul ion traps, which is the focus of this thesis. The objectives here are to develop the theoretical models and to devise the experimental components and methods to investigate the coupling of polar molecular ions' rotational states to the microwave radiation. The new approach presented here is based on co-trapping Sr+ atomic ions together with SrCl+ molecular ions in a cryogenic surface electrode RF ion trap and on using the coupling of the molecular ion's rotational states to an integrated superconducting microwave line or cavity either as a cooling method or for precise rotational spectroscopy. The first part of the thesis describes two theoretical methods for observing the coupling of the microwave radiation to the rotational levels of a molecule. The first method proposed is based on the enhancement of the molecular rotational transition rates by the co-trapped molecular-atomic ions Coulomb collisions. The second method is based on microwave cavity assisted heating or cooling of the molecular ions. The second part of the thesis presents the development of a cryogenic surface electrode RF ion trap with an integrated microwave transmission line/resonator. The ion trap is operated in a 4.2 K closed cycle cryostat.
We present a novel ultrastable superconducting radio-frequency (RF) ion trap realized as a combination of an RF cavity and a linear Paul trap. Its RF quadrupole mode at 34.52 MHz reaches a quality factor of Q ≈ 2.3 × 105 at a temperature of 4.1 K and is used to radially confine ions in an ultralow-noise pseudopotential. This concept is expected to strongly suppress motional heating rates and related frequency shifts that limit the ultimate accuracy achieved in advanced ion traps for frequency metrology. Running with its low-vibration cryogenic cooling system, electron-beam ion trap, and deceleration beamline supplying highly charged ions (HCIs), the superconducting trap offers ideal conditions for optical frequency metrology with ionic species. We report its proof-of-principle operation as a quadrupole-mass filter with HCIs and trapping of Doppler-cooled 9Be+ Coulomb crystals.