In this chapter, the authors describe various types of noise that lead to errors in superconducting quantum computers, and measures that can be taken to mitigate the effect of errors, leading to higher-fidelity results. Error mitigation is different from the quantum error correction techniques. In addition to decoherence, caused by environmental interactions, quantum systems experience errors during state preparation, gates, and measurements. Errors are also created by imperfect quantum gates. A technique known as zero-noise extrapolation does this by artificially increasing the impact of noise in a controlled way, and then extrapolating back to the expected outcome if there were zero noise. The authors briefly introduce recent work on using Deep Reinforcement Learning to optimize the control pulses for one- and two-qubit gates on a superconducting quantum computer, led by Q-CTRL.
In this chapter, the authors describe various types of noise that lead to errors in superconducting quantum computers, and measures that can be taken to mitigate the effect of errors, leading to higher-fidelity results. Error mitigation is different from the quantum error correction techniques. In addition to decoherence, caused by environmental interactions, quantum systems experience errors during state preparation, gates, and measurements. Errors are also created by imperfect quantum gates. A technique known as zero-noise extrapolation does this by artificially increasing the impact of noise in a controlled way, and then extrapolating back to the expected outcome if there were zero noise. The authors briefly introduce recent work on using Deep Reinforcement Learning to optimize the control pulses for one- and two-qubit gates on a superconducting quantum computer, led by Q-CTRL.
A long-standing challenge in quantum computing is developing technologies to overcome the inevitable noise in qubits. To enable meaningful applications in the early stages of fault-tolerant quantum computing, devising methods to suppress post-correction logical failures is becoming increasingly crucial. In this work, we propose and experimentally demonstrate the application of zero-noise extrapolation, a practical quantum error mitigation technique, to error correction circuits on superconducting processors. By amplifying the noise on physical qubits, the circuits yield outcomes that exhibit a predictable dependence on noise strength, following a polynomial function determined by the code distance. This property enables the effective application of polynomial extrapolation to mitigate logical errors. Our experiments demonstrate a universal reduction in logical errors across various quantum circuits, including fault-tolerant circuits of repetition and surface codes. We observe a favorable performance in multi-round error correction circuits, indicating that this method remains effective when the circuit depth increases. These results advance the frontier of quantum error suppression technologies, opening a practical way to achieve reliable quantum computing in the early fault-tolerant era. Quantum error mitigation refers to techniques that reduce, rather than correct, errors in quantum computing. Here the authors demonstrate zero-noise extrapolation applied to quantum error correction circuits on superconducting processors, effectively reducing logical errors and advancing early fault-tolerant quantum computing.
Quantum devices in the noisy intermediate-scale quantum (NISQ) era are highly susceptible to different types of quantum noise, which directly impact the reliability of experimental results. This work provides a characterization of error behavior arising from quantum noises on IBM's superconducting quantum processor, offering practical insights for algorithm design, benchmarking, and error-mitigation strategies on a real superconducting quantum processor in the NISQ era. The study begins with the measurement of the basis state, without applying any gate, to quantify state-preparation and measurement (SPAM) errors. Additionally, the errors are further quantified due to the application of single-qubit Pauli-X, two-qubit CNOT gate and other multi-qubit Controlled-X gates. Each circuit was executed with 1024 shots, and the percentage error between the expected and observed outputs was computed. The results show that the single-qubit Pauli-X gate exhibits relatively low errors in comparison with the two-qubit CNOT gate, whereas other multi-qubit Controlled-X gates lead to significantly higher deviations. This work also analyzes the noise effect of a fourqubit Controlled-X gate being implemented using a three-qubit Controlled-X gate with an extra auxiliary qubit, and the result shows a significant reduction in the error rate.
Quantum computing promises to address problems in simulation, optimization, and chemistry, but current hardware operates in the noisy intermediate-scale (NISQ) regime where coherence limits, gate imperfections, and readout errors restrict performance. Improving calibration and mitigating errors therefore remain essential. This thesis analyzes error reduction on superconducting transmon qubits through calibration, gate analysis, and circuit-level mitigation. It compares single-qubit amplitude calibration methods and analyzes two-qubit gates based on the cross-resonance interaction, identifying differences in precision, convergence, and performance. In addition, it develops Inverted-Circuit Zero-Noise-Extrapolation (IC-ZNE) which measures effective error strength using inverted circuits. Compared to standard ZNE, IC-ZNE achieves results closer to ideal values and reduces observable errors. Overall, the presented methods improve the reliability of near-term quantum processors.
Error mitigation has enabled quantum computing applications with more than a hundred qubits and deep circuits. Many error mitigation methods are noise-aware, relying on a faithful characterization of the noise channels of the hardware. However, fundamental limitations lead to unlearnable degrees of freedom of the underlying noise models when considering qubits. Here, we show how to leverage noncomputational states as an additional resource to learn state-preparation errors in superconducting qubits. This allows one to fully constrain the noise models. We can thus independently and accurately mitigate state-preparation errors, gate errors, and measurement errors. Our proposed method is also applicable to dynamic circuits with midcircuit measurements. This work opens the door to improved error mitigation for measurements, both at the end of the circuit and midcircuit.
We present a simple, malleable and low-overhead approach for improving generic biased quantum error mitigation (QEM) methods, achieving up to 15% fidelity improvements over standard QEM on 100-qubit circuits with up to 2000 entangling gates. We do so by constructing verifiable benchmark circuits which mirror the application circuit's native-gate structure and thus noise profile. These circuits can be used to benchmark and mitigate the bias of the underlying error mitigation method, requiring only the application circuit and hardware native gate set. We present two methods for generating benchmark circuits; one is agnostic to the target hardware at the expense of a small overhead of single-qubit gates, while the other is specific to the IBM superconducting hardware and has no gate overhead. As a corollary, we introduce benchmarked-noise zero-noise extrapolation (bnZNE) as a simple adaptation of zero-noise extrapolation (ZNE), one of the most popular error mitigation methods. We consider as an example the bias-mitigated ZNE and bnZNE of Trotterized Hamiltonian simulations, observing that our approaches outperform standard ZNE using both small-scale classical simulations and 100-qubit utility-scale experiments on the IBM superconducting hardware. We consider the measurement of both single-site observables as well as two-site correlations along a one-dimensional qubit chain. We also provide a software package for implementing the error mitigation techniques used in this research.
Current noisy quantum computers have multiple types of errors, which can occur in the state preparation, measurement/readout, and gate operation, as well as intrinsic decoherence and relaxation. Partly motivated by the booming of intermediate-scale quantum processors, measurement and gate errors have been recently extensively studied, and several methods of mitigating them have been proposed and formulated in software packages (e.g., in IBM Qiskit). Despite this, the state preparation error and the procedure to quantify it have not yet been standardized, as state preparation and measurement errors are usually considered not directly separable. Inspired by a recent work of Laflamme, Lin, and Mor \cite{laflamme2022algorithmic}, we propose a simple and resource-efficient approach to quantify separately the state preparation and readout error rates. With these two errors separately quantified, we also propose methods to mitigate them separately, especially mitigating state preparation errors with linear (with the number of qubits) complexity. As a result of the separate mitigation, we show that the fidelity of the outcome can be improved by an order of magnitude compared to the standard measurement error mitigation scheme. We also show that the quantification and mitigation scheme is resilient against gate noise and can be immediately applied to current noisy quantum computers. To demonstrate this, we present results from cloud experiments on IBM's superconducting quantum computers. The results indicate that the state preparation error rate is also an important metric for qubit metrology that can be efficiently obtained.