Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

International Conference on Electronic Packaging Technology (ICEPT)

Design and Test of Transmission Line in SFQ Circuit

Quan Zhou, Lingyun Li, Zhen Wang, Gaowei Xu, Le Luo, Xiaoming Xie, Kun Li, Jie Ren

Published Sep 14, 2021• 0 citations
Publisher

Abstract

In this paper, the transmission line structure applied to the SFQ circuit was designed and tested. The${4.7\Omega}$impedance MSL designed and prepared based on the Nb-based superconducting process can ensure the PTL circuit to have a current bias margin of 58%, and achieve 0 error rate during the transmission of the SFQ signal. The prepared${50\Omega}$impedance MSL and CPW have been measured for low-temperature and high-frequency S-parameters. The results show that the structure has excellent transmission performance with$\mathbf{S}_{11} {\leqslant-}$15dB and$\mathbf{S}_{21} {\geqslant-1 \text{dB}}$at 0-18GHz.

DOI
10.1109/icept52650.2021.9568131

Related papers

Design of Passive Transmission Line by Adjusting Intrinsic Parameters of Josephson Junctions

Xi Gao, Minghui Niu, Xiaoping Gao +5 more

Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum circuits by adjusting the Stewart McCumber parameter${\beta }_{\bm{C}}$of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from JJ's modified${\beta }_{\bm{C}}$on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. In total,$ \pm $30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.

IEEE Transactions on Applied Superconductivity•May 22, 2023•3 citations

Flexible Superconducting Passive Interconnects with 50-Gb/s Signal Transmissions in Single-Flux-Quantum Circuits

Takahiro Yamada, Hirofumi Ryoki, Akira Fujimaki +1 more

We have developed a very flexible wiring technique of passive transmission lines (PTLs) in single-flux-quantum (SFQ) circuits. For high flexibility, we introduced two types of wiring structures of strip lines (SLs) and microstrip lines (MSLs) using the fabrication process which has four metal layers. The SLs and MSLs are realized using the second and fourth metal layers as signal lines, respectively, from the bottom (the other two metal layers are used as ground planes). We also introduced via-holes for transmission between the SL and MSL. For solving the problem of impedance mismatch on complicated discontinuous sections such as joints [between the driver(receiver) and the end of SLs(MSLs)] and via-holes, we optimized the structures of these discontinuous sections and evaluated propagation properties to ensure high-speed transmission of SFQ pulses. We tested the transmission of SFQ pulses through SLs/MSLs including more than 50 via-holes, one of the most complicated lines in actual designs. We confirmed the good propagation properties of SFQ pulses up to 50 Gb/s with sufficiently wide bias margins of ±20% to be used in practical designs.

Japanese Journal of Applied Physics•Feb 1, 2006•21 citations

Characteristics of driver and receiver circuits with a passive transmission line in RSFQ circuits

Hideo Suzuki, Shuichi Nagasawa, Kazunori Miyahara +1 more

We report simulated results of-rapid single flux quantum (SFQ) circuits having driver, receiver, and passive transmission lines for propagating SFQ pulses to investigate the design criteria. We have studied the equivalent input/output resistance of the driver/receiver in various bias conditions and found that the resistance is almost proportional to the bias current of the driver/receiver. Furthermore, we have proposed inserting a series resistor at the end of the superconducting passive transmission line (PTL) for avoiding undesirable flux trapping in the loop and for isolation in regard to the DC current. We also found that the reduction of the bias margin due to the resistance is rather small when the resistance is much smaller than the impedance of the PTL. An operating margin of more than 30% was obtained in the driver/receiver circuits including the PTL and the series resistor.

IEEE Transactions on Applied Superconductivity•Jan 1, 2000•30 citations

Investigation of Passive Transmission Lines for the MIT-LL SFQ5ee Process

Ashish Shukla, Benjamin Chonigman, Anubhav Sahu +3 more

As the complexity of superconductor circuits grows, we envision a dense network of passive transmission lines (PTLs) being used to interconnect cells in rapid-single-flux-quantum (RSFQ) circuits. In our library approach, each cell has dedicated tracks as place holders for routing PTLs. Higher impedance PTLs are desirable due to their narrower width. However, at higher impedance, the margins for the PTL receiver degrade rapidly. We have designed, fabricated, tested, and simulated passive transmission lines (PTLs) for high-speed interconnects in the MIT-LL SFQ5ee 10 kA/cm2process. For the symmetric dual ground planes case, PTLs are in the M1 layer with M0 and M2 ground planes, or in the M3 layer with M2 and M4 ground planes. For the asymmetrical dual ground planes case, PTLs are in M2 or M3 layers with M1 and M4 ground planes. We report ±30% margins for these PTLs. We investigate the receiver margins for these PTLs and report impact of margins as a function of corners, interlayer transitions, variants of drivers, and receivers. We demonstrate 100 GHz PTL operation in ring oscillator measurements. We have also adopted multi-layer multi-conductor transmission line models for PTL simulation. We observe good model-to-hardware correlation for low- and high-frequency operation.

IEEE Transactions on Applied Superconductivity•Mar 8, 2019•30 citations

Coplanar waveguide superconducting microwave power divider: Design, preparation and experimental tests

Bo Zhang, Qing He, Xin-Da Yang +3 more

Power divider is a useful device that divides the power of signal into different subpowers at a certain ratio. The superconducting power divider plays an important role in various superconducting quantum computing circuits and superconducting microwave photon detectors. Therefore, in this paper we investigate how to design and prepare a typical coplanar waveguide superconducting microwave power divider. The parameters are designed by using the odd-even mode method to analyze the transport features of a three-port microwave network. Specifically, the microwave transport properties of the device with a center frequency of 5 GHz and 3 dB power division ratio are simulated. Then, the designed aluminum coplanar waveguide superconducting power divider on silicon is prepared by micro-processing technology and experimentally tested at low temperature. It is shown that the measurement results are consistent with the design parameters. It is noted that the center frequency of the actually prepared power divider is measured to be about 5.25 GHz, which is slightly different from the result of the design and simulation. This difference is probably due to the following main reasons. Firstly, the limited precision of the micromachining process is caused by the fact that the fabricated quarter-wave impedance matching line is etched incompletely, leading the length of the impedance matching line to be shortened. As a consequence, the frequency of the prepared power divider is slightly higher. Secondly, the simulation software is not designed specially for superconducting device simulations, thereby yielding the design parameters slightly different from those of the fabricated superconducting devices. Additionally, a series of attenuations has been used in the experimental test system of the superconducting microwave power dividers for reducing the various noises. This causes the input test signal to weaken, thus the reflected signal turns significantly small. Therefore, none of the S11 parameters of the device can be effectively measured. Finally, neither of S21 and S31 parameters measured in the experiment is the predicted –3 dB, which is mainly due to the imperfections in the welding between SMA connectors and high-frequency transmission lines, and the spot welding between high-frequency transmission lines and power divider samples, and also due to the discontinuities of the high-frequency transmission line and the power divider and so on. All these factors can yield the tested insertion loss of the device. Hopefully, the method in this work can be extended to designing and preparing other passive superconducting microwave devices.

Acta Physica Sinica•Jan 1, 2021•0 citations

Timing Evaluation of Passive Transmission Line by RSFQ Ring Oscillator

Xi Gao, Huanli Liu, Xiaoping Gao +2 more

Passive transmission line (PTL) has been widely applied in rapid single flux quantum (RSFQ) circuits, especially as the first choice of long-distance transmission in large-scale integrated circuits such as arithmetic and logic unit (ALU) and central processing unit (CPU). With the increasing demand of timing regulation, general bias margin is not enough to evaluate the performance of PTL circuits. Timing accuracy including propagation delay of the micro stripe line (MSL) and its delay skew is more critical for clock routine and signal transmission when employing PTL circuits. However, the related reports about the timing information of PTL circuits is limited in the single-value verification of the theoretical MSL's delay. More factors such as bias current, transmission length and system noise should be considered into the evaluation of the PTL circuits. This work focuses on the timing extraction of the designed PTL circuits through different control groups, and evaluates the timing discrepancy between the measurement and simulation. We adopt the method of time accumulation by increasing different lengths of MSL in the loop of the ring oscillator (RO) and subtract each other to evaluate the MSL's propagation delay. We analyzed MSLs of two layers (MSL1 and MSL2). The measured propagation delay of 1${\bm{mm}}$MSL is 8.20${\bm{ps}}/{\bm{mm}}\ $for MSL1 and 7.66${\bm{ps}}/{\bm{mm}}$for MSL2, which has a delay skew of 0.30${\bm{ps}}$and 0.57${\bm{ps}}$from the simulated value (8.23${\bm{ps}}$). Within MSL transmission length of 5${\bm{mm}}$, a maximum deviation of 1.2${\bm{ps}}$is adopted as time redundancy of PTL circuits applied in ALU and CPU design.

IEEE Transactions on Applied Superconductivity•Feb 5, 2024•1 citation
In this paper, the transmission line structure applied to the SFQ circuit was designed and tested. The4.7Ω{4.7\Omega}4.7Ωimpedance MSL designed and prepared based on the Nb-based superconducting process can ensure the PTL circuit to have a current bias margin of 58%, and achieve 0 error rate during the transmission of the SFQ signal. The prepared50Ω{50\Omega}50Ωimpedance MSL and CPW have been measured for low-temperature and high-frequency S-parameters. The results show that the structure has excellent transmission performance withS11⩽−\mathbf{S}_{11} {\leqslant-}S11​⩽−15dB andS21⩾−1dB\mathbf{S}_{21} {\geqslant-1 \text{dB}}S21​⩾−1dBat 0-18GHz.
Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum circuits by adjusting the Stewart McCumber parameterβC{\beta }_{\bm{C}}βC​of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from JJ's modifiedβC{\beta }_{\bm{C}}βC​on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. In total,$ \pm $30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.
We have developed a very flexible wiring technique of passive transmission lines (PTLs) in single-flux-quantum (SFQ) circuits. For high flexibility, we introduced two types of wiring structures of strip lines (SLs) and microstrip lines (MSLs) using the fabrication process which has four metal layers. The SLs and MSLs are realized using the second and fourth metal layers as signal lines, respectively, from the bottom (the other two metal layers are used as ground planes). We also introduced via-holes for transmission between the SL and MSL. For solving the problem of impedance mismatch on complicated discontinuous sections such as joints [between the driver(receiver) and the end of SLs(MSLs)] and via-holes, we optimized the structures of these discontinuous sections and evaluated propagation properties to ensure high-speed transmission of SFQ pulses. We tested the transmission of SFQ pulses through SLs/MSLs including more than 50 via-holes, one of the most complicated lines in actual designs. We confirmed the good propagation properties of SFQ pulses up to 50 Gb/s with sufficiently wide bias margins of ±20% to be used in practical designs.
We report simulated results of-rapid single flux quantum (SFQ) circuits having driver, receiver, and passive transmission lines for propagating SFQ pulses to investigate the design criteria. We have studied the equivalent input/output resistance of the driver/receiver in various bias conditions and found that the resistance is almost proportional to the bias current of the driver/receiver. Furthermore, we have proposed inserting a series resistor at the end of the superconducting passive transmission line (PTL) for avoiding undesirable flux trapping in the loop and for isolation in regard to the DC current. We also found that the reduction of the bias margin due to the resistance is rather small when the resistance is much smaller than the impedance of the PTL. An operating margin of more than 30% was obtained in the driver/receiver circuits including the PTL and the series resistor.
As the complexity of superconductor circuits grows, we envision a dense network of passive transmission lines (PTLs) being used to interconnect cells in rapid-single-flux-quantum (RSFQ) circuits. In our library approach, each cell has dedicated tracks as place holders for routing PTLs. Higher impedance PTLs are desirable due to their narrower width. However, at higher impedance, the margins for the PTL receiver degrade rapidly. We have designed, fabricated, tested, and simulated passive transmission lines (PTLs) for high-speed interconnects in the MIT-LL SFQ5ee 10 kA/cm2process. For the symmetric dual ground planes case, PTLs are in the M1 layer with M0 and M2 ground planes, or in the M3 layer with M2 and M4 ground planes. For the asymmetrical dual ground planes case, PTLs are in M2 or M3 layers with M1 and M4 ground planes. We report ±30% margins for these PTLs. We investigate the receiver margins for these PTLs and report impact of margins as a function of corners, interlayer transitions, variants of drivers, and receivers. We demonstrate 100 GHz PTL operation in ring oscillator measurements. We have also adopted multi-layer multi-conductor transmission line models for PTL simulation. We observe good model-to-hardware correlation for low- and high-frequency operation.
Power divider is a useful device that divides the power of signal into different subpowers at a certain ratio. The superconducting power divider plays an important role in various superconducting quantum computing circuits and superconducting microwave photon detectors. Therefore, in this paper we investigate how to design and prepare a typical coplanar waveguide superconducting microwave power divider. The parameters are designed by using the odd-even mode method to analyze the transport features of a three-port microwave network. Specifically, the microwave transport properties of the device with a center frequency of 5 GHz and 3 dB power division ratio are simulated. Then, the designed aluminum coplanar waveguide superconducting power divider on silicon is prepared by micro-processing technology and experimentally tested at low temperature. It is shown that the measurement results are consistent with the design parameters. It is noted that the center frequency of the actually prepared power divider is measured to be about 5.25 GHz, which is slightly different from the result of the design and simulation. This difference is probably due to the following main reasons. Firstly, the limited precision of the micromachining process is caused by the fact that the fabricated quarter-wave impedance matching line is etched incompletely, leading the length of the impedance matching line to be shortened. As a consequence, the frequency of the prepared power divider is slightly higher. Secondly, the simulation software is not designed specially for superconducting device simulations, thereby yielding the design parameters slightly different from those of the fabricated superconducting devices. Additionally, a series of attenuations has been used in the experimental test system of the superconducting microwave power dividers for reducing the various noises. This causes the input test signal to weaken, thus the reflected signal turns significantly small. Therefore, none of the S11 parameters of the device can be effectively measured. Finally, neither of S21 and S31 parameters measured in the experiment is the predicted –3 dB, which is mainly due to the imperfections in the welding between SMA connectors and high-frequency transmission lines, and the spot welding between high-frequency transmission lines and power divider samples, and also due to the discontinuities of the high-frequency transmission line and the power divider and so on. All these factors can yield the tested insertion loss of the device. Hopefully, the method in this work can be extended to designing and preparing other passive superconducting microwave devices.
Passive transmission line (PTL) has been widely applied in rapid single flux quantum (RSFQ) circuits, especially as the first choice of long-distance transmission in large-scale integrated circuits such as arithmetic and logic unit (ALU) and central processing unit (CPU). With the increasing demand of timing regulation, general bias margin is not enough to evaluate the performance of PTL circuits. Timing accuracy including propagation delay of the micro stripe line (MSL) and its delay skew is more critical for clock routine and signal transmission when employing PTL circuits. However, the related reports about the timing information of PTL circuits is limited in the single-value verification of the theoretical MSL's delay. More factors such as bias current, transmission length and system noise should be considered into the evaluation of the PTL circuits. This work focuses on the timing extraction of the designed PTL circuits through different control groups, and evaluates the timing discrepancy between the measurement and simulation. We adopt the method of time accumulation by increasing different lengths of MSL in the loop of the ring oscillator (RO) and subtract each other to evaluate the MSL's propagation delay. We analyzed MSLs of two layers (MSL1 and MSL2). The measured propagation delay of 1mm{\bm{mm}}mmMSL is 8.20${\bm{ps}}/{\bm{mm}}\ forMSL1and7.66for MSL1 and 7.66forMSL1and7.66{\bm{ps}}/{\bm{mm}}forMSL2,whichhasadelayskewof0.30for MSL2, which has a delay skew of 0.30forMSL2,whichhasadelayskewof0.30{\bm{ps}}and0.57and 0.57and0.57{\bm{ps}}fromthesimulatedvalue(8.23from the simulated value (8.23fromthesimulatedvalue(8.23{\bm{ps}}).WithinMSLtransmissionlengthof5). Within MSL transmission length of 5).WithinMSLtransmissionlengthof5{\bm{mm}},amaximumdeviationof1.2, a maximum deviation of 1.2,amaximumdeviationof1.2{\bm{ps}}$is adopted as time redundancy of PTL circuits applied in ALU and CPU design.