We have developed a very flexible wiring technique of passive transmission lines (PTLs) in single-flux-quantum (SFQ) circuits. For high flexibility, we introduced two types of wiring structures of strip lines (SLs) and microstrip lines (MSLs) using the fabrication process which has four metal layers. The SLs and MSLs are realized using the second and fourth metal layers as signal lines, respectively, from the bottom (the other two metal layers are used as ground planes). We also introduced via-holes for transmission between the SL and MSL. For solving the problem of impedance mismatch on complicated discontinuous sections such as joints [between the driver(receiver) and the end of SLs(MSLs)] and via-holes, we optimized the structures of these discontinuous sections and evaluated propagation properties to ensure high-speed transmission of SFQ pulses. We tested the transmission of SFQ pulses through SLs/MSLs including more than 50 via-holes, one of the most complicated lines in actual designs. We confirmed the good propagation properties of SFQ pulses up to 50 Gb/s with sufficiently wide bias margins of ±20% to be used in practical designs.
We have developed a very flexible wiring technique of passive transmission lines (PTLs) in single-flux-quantum (SFQ) circuits. For high flexibility, we introduced two types of wiring structures of strip lines (SLs) and microstrip lines (MSLs) using the fabrication process which has four metal layers. The SLs and MSLs are realized using the second and fourth metal layers as signal lines, respectively, from the bottom (the other two metal layers are used as ground planes). We also introduced via-holes for transmission between the SL and MSL. For solving the problem of impedance mismatch on complicated discontinuous sections such as joints [between the driver(receiver) and the end of SLs(MSLs)] and via-holes, we optimized the structures of these discontinuous sections and evaluated propagation properties to ensure high-speed transmission of SFQ pulses. We tested the transmission of SFQ pulses through SLs/MSLs including more than 50 via-holes, one of the most complicated lines in actual designs. We confirmed the good propagation properties of SFQ pulses up to 50 Gb/s with sufficiently wide bias margins of ±20% to be used in practical designs.
We have studied single-flux-quantum (SFQ) propagation properties in passive transmission lines (PTLs) based on a 10-Nb-layer device structure (ADP2). In ADP2, we can use the PTLs with a line width about 5 mum, one seventh of conventional line width by adopting a strip line (SL) structure and increasing the characteristic impedance. The evaluation has been conducted on the PTL length and the via-hole structure by using ring oscillators. We found that the decrease in the operating region was larger for longer PTL, compared with that in a conventional device structure (STD2). The results would be caused by the increase in the surface resistance. The via-holes connecting the PTLs on different layers have more complicated structure than those of STD2. We have designed the via-hole structure using the electromagnetic wave simulator HFSS. As a result, we have demonstrated sufficiently large operating margins at any data rates up to 80 Gb/s even for the ring oscillator with 30 via-holes.
As the complexity of superconductor circuits grows, we envision a dense network of passive transmission lines (PTLs) being used to interconnect cells in rapid-single-flux-quantum (RSFQ) circuits. In our library approach, each cell has dedicated tracks as place holders for routing PTLs. Higher impedance PTLs are desirable due to their narrower width. However, at higher impedance, the margins for the PTL receiver degrade rapidly. We have designed, fabricated, tested, and simulated passive transmission lines (PTLs) for high-speed interconnects in the MIT-LL SFQ5ee 10 kA/cm2process. For the symmetric dual ground planes case, PTLs are in the M1 layer with M0 and M2 ground planes, or in the M3 layer with M2 and M4 ground planes. For the asymmetrical dual ground planes case, PTLs are in M2 or M3 layers with M1 and M4 ground planes. We report ±30% margins for these PTLs. We investigate the receiver margins for these PTLs and report impact of margins as a function of corners, interlayer transitions, variants of drivers, and receivers. We demonstrate 100 GHz PTL operation in ring oscillator measurements. We have also adopted multi-layer multi-conductor transmission line models for PTL simulation. We observe good model-to-hardware correlation for low- and high-frequency operation.
Passive transmission lines (PTLs) provide an energy-efficient means of transporting pulsed single flux quantum (SFQ) signals between logic gates and blocks on a chip, or even between chips through a multi-chip module carrier. Although functional up to 70 GHz, our previous designs manifested sharp, length-dependent resonances resulting in diminished operating margins. These are particularly inconvenient since the resonant length is about 1 mm at 40–50 GHz, where most SFQ circuits currently function. To avoid the need to keep the PTLs < 1 mm in length, we have optimized the PTL driver-receiver pairs to sufficiently suppress these resonances; this helps facilitate the use of automated routing tools. We present experimental results, in the 10-70 GHz frequency range, for different driver-receiver pairs designed for PTLs in our dual RSFQ-ERSFQ cell library. This cell library, targeting MIT Lincoln Laboratory's SFQ5ee fabrication process, uses PTLs with two types of ground plane configuration. The first variant has signal in M1 and/or M3 with symmetrical ground planes in M0, M2 and/or M2, M4 respectively. The second variant has signal in M2 and/or M3 with asymmetrical ground planes in M1 and M4. We also present a comparison with wider, 4 Ω, PTLs that are more suitable for transport between distant logic blocks. Next, we present experimental results of PTL lengths ranging from 1.2-12 mm over the same 10-70 GHz frequency range. Finally, we report on the design of circuits for investigating crosstalk between two PTLs and their measurement results.
The increasing complexity of modern rapid single flux quantum (RSFQ) circuits has made on-chip signal routing, an issue of growing importance. In this paper, several methods for routing large-scale RSFQ circuits are described, and a process is presented for determining when to use passive microstrip transmission lines (PTL) and active Josephson transmission lines (JTL). The effect of the size of the JTL inductor and Josephson junctions on the length of a JTL chain for a target delay is also discussed. The dependence of the JTL inductance on the physical layout is evaluated, and the effects of the primary PTL parameters on delay are characterized. A novel PTL driver and receiver configuration is also proposed. Tradeoffs among the number of JJs, inductance, and length of a PTL stripline in the receiver and driver circuits are reported. The energy dissipation is evaluated for two different interconnects. A tradeoff between the proposed PTL circuits and an optimized JTL in terms of energy dissipation and delay is discussed. Guidelines for choosing the optimal element values are determined, and a simulated bias margin of ±29% for the bias current of the proposed receiver operating at 20 GHz in a 10 kA/cm2technology for a 1-mm transmission line is achieved. Summarizing, guidelines and design tradeoffs appropriate for automated layout and synthesis are provided for driving long interconnect in SFQ VLSI circuits.
To enable the use of passive transmission lines (PTLs) for the interconnection of single-flux-quantum (SFQ) circuits, we have implemented a driver and a receiver and have developed a method for designing SFQ circuits with passive interconnections. Basic components and properties of passive interconnections, such as the frequency characteristics of the driver and receiver, the PTL delay, and the crosstalk between PTLs, have been experimentally verified. Our developed components and design method have been applied to actual SFQ circuits, such as a 4 x 4 switch having block-to-block passive interconnections and a 2 x 2 switch having gate-to-gate passive interconnections. We have also shown the advantages of PTLs over Josephson transmission lines (JTLs). We also discuss the prospects of SFO circuits having passive interconnections.
Superconductive passive transmission lines (PTL) are widely used for signal routing in large-scale rapid single flux quantum (RSFQ) circuits. Due to the imperfect matching of the transmission lines between the driver and receiver, single flux quantum (SFQ) pulses are partially reflected. The round trip propagation time of these reflections can coincide with the following SFQ pulse, resulting in a decrease in bias margins or incorrect circuit behavior. This resonant effect depends upon the length of the PTL and the clock frequency of the signal. A methodology to reduce and manage this effect is the focus of this article. A closed-form expression describing the dependence of the resonance frequency on the length of the PTL is presented. This expression describes a set of forbidden lengths for PTL interconnect segments in RSFQ circuits. The proposed methodology and algorithm insert active PTL-based repeaters into long superconductive interconnect while ensuring the length of the line segment is outside the forbidden region and increasing bias margins.