Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

The Japan Society of Applied Physics

Non-linear effect in the superconducting transmission line

Takashi Noguchi, S. Mima, Chiko Otani

Published Jul 9, 2020• 0 citations
OpenAlex

Related papers

Quantum limited heterodyne detection in superconducting non-linear transmission lines at sub-millimeter wavelengths

Edward Tong, R. Blundell, B. Bumble +2 more

A non-linear superconducting transmission line has been successfully employed in heterodyne detection of sub-millimeter waves. In our experiments an Nb/Al/AlOx/Nb tunnel junction, measuring 0.15×40 μm, with a critical current density of about 2500 A/cm2 is used as a distributed mixer element. We have demonstrated that quantum limited sensitivity can be achieved with this type of device. At 460 GHz, a Y-factor of 2.5 has been recorded, corresponding to a double-side-band receiver noise temperature of 80 K. The double-side-band conversion loss is about 1 dB and the mixer noise temperature is estimated to be 18(±10) K.

Applied Physics Letters•Aug 28, 1995•37 citations

Study of Coupling in Superconducting Transmission Lines

D. Valenzuela

Journal of Superconductivity and Novel Magnetism•Feb 9, 2024•0 citations

Transmission properties of fishbone-type superconducting transmission lines

Kohki Nakagawa, Masanori Takeda, Atsushi SAITO +1 more

Abstract Fishbone-type superconducting transmission lines (FSTLs) is a periodic transmission line. Herein, we analyzed the characteristic impedance and effective wavelength of FSTLs using the equivalent circuit. Based on the obtained results, we designed and fabricated an FSTL half-wavelength resonator. The resonator measurement revealed that the effective wavelength of the FSTL is shorter than half of that of the coplanar waveguide. Furthermore, we obtained the kinetic inductance per unit length of the FSTL by comparing the analyzed and measured resonance frequencies.

Japanese Journal of Applied Physics•Oct 8, 2020•2 citations

A New Nonlinearity for Superconducting Circuits

Marric Stephens

Physics•Sep 5, 2024•0 citations

Inductances in Superconducting Circuits

Pascal Febvre

•Feb 19, 2018•0 citations

Modeling losses in microstrip traveling wave kinetic inductance parametric amplifiers using the four and three wave mixing effect

Valenzuela Henríquez, Daniel Alejandro

The performance of an amplifier is based on a high gain and a low noise. To minimize \nthe noise problem at high frequencies, the superconducting parametric amplifier has been \ndeveloped. It is a system that uses a non-linear process and a strong reference to transfer \nthe energy to the original signal and their harmonics. Two types of processes are discussed in \nthis thesis, the Four and Three-wave mixing (FWM and TWM). \nOne implementation is the travelling-wave kinetic inductance parametric amplifier (TKIPA). \nIt consists of a superconducting transmission line (TL), which uses its non-linear inductance \nto transfer the energy to the input signal. With the appropriated design, the blocking of \nundesirable harmonics to concentrate the power in the signal (and not in the harmonics) \nis possible. The first implementation of the TKIPA used a coplanar wave-guide (CPW), \nwhere impedances near 50 Ω are difficult to achieve. In this thesis, a TKIPA was designed \nusing a microstrip. A 50 Ω microstrip line is easier to obtain, circumventing the problem of \nimpedance mismatch with output electronics. \nWe have presented two designs of a TKIPA based on superconducting microstrip, supporting FWM and TWM, respectively. Simulation results show that the designs blocked \nthe undesirable frequencies, while obtaining a ≈ 50 Ω line. The losses in the device do not \ndeteriorate significantly the performance of the device.

•Jan 1, 2020•1 citation
A non-linear superconducting transmission line has been successfully employed in heterodyne detection of sub-millimeter waves. In our experiments an Nb/Al/AlOx/Nb tunnel junction, measuring 0.15×40 μm, with a critical current density of about 2500 A/cm2 is used as a distributed mixer element. We have demonstrated that quantum limited sensitivity can be achieved with this type of device. At 460 GHz, a Y-factor of 2.5 has been recorded, corresponding to a double-side-band receiver noise temperature of 80 K. The double-side-band conversion loss is about 1 dB and the mixer noise temperature is estimated to be 18(±10) K.
Abstract Fishbone-type superconducting transmission lines (FSTLs) is a periodic transmission line. Herein, we analyzed the characteristic impedance and effective wavelength of FSTLs using the equivalent circuit. Based on the obtained results, we designed and fabricated an FSTL half-wavelength resonator. The resonator measurement revealed that the effective wavelength of the FSTL is shorter than half of that of the coplanar waveguide. Furthermore, we obtained the kinetic inductance per unit length of the FSTL by comparing the analyzed and measured resonance frequencies.
The performance of an amplifier is based on a high gain and a low noise. To minimize \nthe noise problem at high frequencies, the superconducting parametric amplifier has been \ndeveloped. It is a system that uses a non-linear process and a strong reference to transfer \nthe energy to the original signal and their harmonics. Two types of processes are discussed in \nthis thesis, the Four and Three-wave mixing (FWM and TWM). \nOne implementation is the travelling-wave kinetic inductance parametric amplifier (TKIPA). \nIt consists of a superconducting transmission line (TL), which uses its non-linear inductance \nto transfer the energy to the input signal. With the appropriated design, the blocking of \nundesirable harmonics to concentrate the power in the signal (and not in the harmonics) \nis possible. The first implementation of the TKIPA used a coplanar wave-guide (CPW), \nwhere impedances near 50 Ω are difficult to achieve. In this thesis, a TKIPA was designed \nusing a microstrip. A 50 Ω microstrip line is easier to obtain, circumventing the problem of \nimpedance mismatch with output electronics. \nWe have presented two designs of a TKIPA based on superconducting microstrip, supporting FWM and TWM, respectively. Simulation results show that the designs blocked \nthe undesirable frequencies, while obtaining a ≈ 50 Ω line. The losses in the device do not \ndeteriorate significantly the performance of the device.