Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Modeling losses in microstrip traveling wave kinetic inductance parametric amplifiers using the four and three wave mixing effect

Valenzuela Henríquez, Daniel Alejandro

Published Jan 1, 2020• 1 citation
OpenAlex

Abstract

The performance of an amplifier is based on a high gain and a low noise. To minimize \nthe noise problem at high frequencies, the superconducting parametric amplifier has been \ndeveloped. It is a system that uses a non-linear process and a strong reference to transfer \nthe energy to the original signal and their harmonics. Two types of processes are discussed in \nthis thesis, the Four and Three-wave mixing (FWM and TWM). \nOne implementation is the travelling-wave kinetic inductance parametric amplifier (TKIPA). \nIt consists of a superconducting transmission line (TL), which uses its non-linear inductance \nto transfer the energy to the input signal. With the appropriated design, the blocking of \nundesirable harmonics to concentrate the power in the signal (and not in the harmonics) \nis possible. The first implementation of the TKIPA used a coplanar wave-guide (CPW), \nwhere impedances near 50 Ω are difficult to achieve. In this thesis, a TKIPA was designed \nusing a microstrip. A 50 Ω microstrip line is easier to obtain, circumventing the problem of \nimpedance mismatch with output electronics. \nWe have presented two designs of a TKIPA based on superconducting microstrip, supporting FWM and TWM, respectively. Simulation results show that the designs blocked \nthe undesirable frequencies, while obtaining a ≈ 50 Ω line. The losses in the device do not \ndeteriorate significantly the performance of the device.

Related papers

Four wave-mixing in a microstrip kinetic inductance travelling wave parametric amplifier

Samuel Goldstein, Naftali Kirsh, Elisha Svetitsky +4 more

Superconducting quantum circuits are typically operated at low temperatures (mK), necessitating cryogenic low-noise, wideband amplifiers for signal readout ultimately also compatible with room temperature electronics. While existing implementations partly meet these criteria, they suffer from certain limitations, such as rippled transmission spectra or limited dynamic range, some of which are caused by the lack of proper impedance matching. We develop a microstrip kinetic inductance traveling wave amplifier, exploiting the nonlinear kinetic inductance of tungsten-silicide for wave-mixing of the signal and a pump, and engineer the impedance to 50 Ω, while decreasing the phase velocity, with benefit for the amplification. Despite losses, pumping on our device amplifies the signal by 15 dB over a 2 GHz bandwidth.

arXiv:2004.10532•Applied Physics Letters•Apr 13, 2020•26 citations

A 4–8 GHz kinetic inductance traveling-wave parametric amplifier using four-wave mixing with near quantum-limited noise performance

Farzad Faramarzi, Ryan Stephenson, Sasha Sypkens +3 more

Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.

arXiv:2402.11751•APL Quantum•Jul 11, 2024•32 citations

Kinetic Inductance Traveling Wave Amplifier Designs for Practical Microwave Readout Applications

Andrea Giachero, Michael R. Vissers, Jordan Wheeler +6 more

Abstract A Kinetic Inductance Traveling Wave Amplifier (KIT) utilizes the nonlinear kinetic inductance of superconducting films, particularly niobium titanium nitride (NbTiN), for parametric amplification. These amplifiers achieve remarkable performance in terms of gain, bandwidth, and compression power and frequently approach the quantum limit for noise. However, most KIT demonstrations have been isolated from practical device readout systems. Using a KIT as the first amplifier in the readout chain of an unoptimized microwave SQUID multiplexer coupled to a transition-edge sensor microcalorimeter, we see an initial improvement in the flux noise [1]. One challenge in KIT integration is the considerable microwave pump power required to drive the non-linearity. To address this, we have initiated efforts to reduce the pump power by using thinner NbTiN films and an inverted microstrip transmission line design. In this article, we present the new transmission line design, fabrication procedure, and initial device characterization—including gain and added noise. These devices exhibit over 10 dB of gain with a 3 dB bandwidth of approximately 5.5–7.25 GHz, a maximum practical gain of 12 dB, and typical gain ripple under 4 dB peak to peak. We observe an appreciable impedance mismatch in the NbTiN transmission line, which is likely the source of the majority of the gain ripple. Finally, we perform an initial noise characterization and demonstrate system-added noise of three quanta or less over nearly the entire 3 dB bandwidth.

arXiv:2403.11354•Journal of Low Temperature Physics•Apr 5, 2024•16 citations

Wideband superconducting parametric amplifiers based on kinetic inductance (Conference Presentation)

Peter K. Day, Byeong Ho Eom, Henry George LeDuc

Traveling-wave parametric amplifiers based on superconducting NbTiN films are being developed that provide gain over nearly an octave of bandwidth at microwave frequencies. The amplifiers are non-linear transmission lines, where the nonlinearity comes from the current dependence of the kinetic inductance. Amplification results from three and four-wave mixing processes, and phase matching over a wide frequency range is achieved by engineering the dispersion characteristics of the transmission line. Recent noise measurements over a wide frequency band demonstrate that the added noise of these amplifiers is close to one half photon, consistent with the quantum limit for a phase preserving amplifier. We will discuss applications of this class of amplifier to astronomical instruments.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jul 10, 2018•1 citation

Simulating the behaviour of travelling wave superconducting parametric amplifiers using a commercial circuit simulator

Thomas Sweetnam, D. Banys, V. Gilles +2 more

Abstract Kinetic inductance travelling wave parametric amplifiers (KI-TWPAs) have been simulated using Keysight’s Advanced Design System. A lumped element representation of a superconducting transmission line has been developed using nonlinear inductor elements to represent the current dependency of the intrinsic kinetic inductance. This provides a fast, simple and easily modifiable method for analysing the parametric processes that occur in nonlinear kinetic inductance devices, such as parametric oscillators or amplifiers while also allowing the accompanying RF network to be optimised. This methodology is used to model the behaviour of a select number of KI-TWPA designs operating in the 3-wave mixing (3WM) and 4-wave mixing (4WM) regimes. S-parameters and dispersion properties are extracted from large signal S-parameter simulations, and the gain curve of each amplifier design is generated from harmonic balance simulations. The results are compared to the gain expression from the analytic solutions of the coupled mode equations while making reference to the gain curves of the equivalent KI-TWPAs from literature.

arXiv:2203.09660•Superconductor Science and Technology•Jul 28, 2022•15 citations

Engineering the thin film characteristics for optimal performance of superconducting kinetic inductance amplifiers using a rigorous modelling technique

Boon-Kok Tan, Faouzi M. Boussaha, Christine Chaumont +2 more

Background: Kinetic Inductance Travelling Wave Parametric Amplifiers (KITWPAs) are a variant of superconducting amplifier that can potentially achieve high gain with quantum-limited noise performance over broad bandwidth, which is important for many ultra-sensitive experiments. In this paper, we present a novel modelling technique that can better capture the electromagnetic behaviour of a KITWPA without the translation symmetry assumption, allowing us to flexibly explore the use of more complex transmission line structures and better predict their performance. Methods: In order to design a KITWPA with optimal performance, we investigate the use of different superconducting thin film materials, and compare their pros and cons in forming a high-gain low-loss medium feasible for amplification. We establish that if the film thickness can be controlled precisely, the material used has less impact on the performance of the device, as long as it is topologically defect-free and operating within its superconducting regime. With this insight, we propose the use of Titanium Nitride (TiN) film for our KITWPA as its critical temperature can be easily altered to suit our applications. We further investigate the topological effect of different commonly used superconducting transmission line structures with the TiN film, including the effect of various non-conducting materials required to form the amplifier. Results: Both of these comprehensive studies led us to two configurations of the KITWPA: 1) A low-loss 100 nm thick TiN coplanar waveguide amplifier, and 2) A compact 50 nm TiN inverted microstrip amplifier. We utilise the novel modelling technique described in the first part of the paper to explore and investigate the optimal design and operational setup required to achieve high gain with the broadest bandwidth for both KITWPAs, including the effect of loss. Conclusions: Finally, we conclude the paper with the actual layout and the predicted gain-bandwidth product of our KITWPAs.

Open Research Europe•Jul 19, 2022•9 citations
The performance of an amplifier is based on a high gain and a low noise. To minimize \nthe noise problem at high frequencies, the superconducting parametric amplifier has been \ndeveloped. It is a system that uses a non-linear process and a strong reference to transfer \nthe energy to the original signal and their harmonics. Two types of processes are discussed in \nthis thesis, the Four and Three-wave mixing (FWM and TWM). \nOne implementation is the travelling-wave kinetic inductance parametric amplifier (TKIPA). \nIt consists of a superconducting transmission line (TL), which uses its non-linear inductance \nto transfer the energy to the input signal. With the appropriated design, the blocking of \nundesirable harmonics to concentrate the power in the signal (and not in the harmonics) \nis possible. The first implementation of the TKIPA used a coplanar wave-guide (CPW), \nwhere impedances near 50 Ω are difficult to achieve. In this thesis, a TKIPA was designed \nusing a microstrip. A 50 Ω microstrip line is easier to obtain, circumventing the problem of \nimpedance mismatch with output electronics. \nWe have presented two designs of a TKIPA based on superconducting microstrip, supporting FWM and TWM, respectively. Simulation results show that the designs blocked \nthe undesirable frequencies, while obtaining a ≈ 50 Ω line. The losses in the device do not \ndeteriorate significantly the performance of the device.
Superconducting quantum circuits are typically operated at low temperatures (mK), necessitating cryogenic low-noise, wideband amplifiers for signal readout ultimately also compatible with room temperature electronics. While existing implementations partly meet these criteria, they suffer from certain limitations, such as rippled transmission spectra or limited dynamic range, some of which are caused by the lack of proper impedance matching. We develop a microstrip kinetic inductance traveling wave amplifier, exploiting the nonlinear kinetic inductance of tungsten-silicide for wave-mixing of the signal and a pump, and engineer the impedance to 50 Ω, while decreasing the phase velocity, with benefit for the amplification. Despite losses, pumping on our device amplifies the signal by 15 dB over a 2 GHz bandwidth.
Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.
Abstract A Kinetic Inductance Traveling Wave Amplifier (KIT) utilizes the nonlinear kinetic inductance of superconducting films, particularly niobium titanium nitride (NbTiN), for parametric amplification. These amplifiers achieve remarkable performance in terms of gain, bandwidth, and compression power and frequently approach the quantum limit for noise. However, most KIT demonstrations have been isolated from practical device readout systems. Using a KIT as the first amplifier in the readout chain of an unoptimized microwave SQUID multiplexer coupled to a transition-edge sensor microcalorimeter, we see an initial improvement in the flux noise [1]. One challenge in KIT integration is the considerable microwave pump power required to drive the non-linearity. To address this, we have initiated efforts to reduce the pump power by using thinner NbTiN films and an inverted microstrip transmission line design. In this article, we present the new transmission line design, fabrication procedure, and initial device characterization—including gain and added noise. These devices exhibit over 10 dB of gain with a 3 dB bandwidth of approximately 5.5–7.25 GHz, a maximum practical gain of 12 dB, and typical gain ripple under 4 dB peak to peak. We observe an appreciable impedance mismatch in the NbTiN transmission line, which is likely the source of the majority of the gain ripple. Finally, we perform an initial noise characterization and demonstrate system-added noise of three quanta or less over nearly the entire 3 dB bandwidth.
Traveling-wave parametric amplifiers based on superconducting NbTiN films are being developed that provide gain over nearly an octave of bandwidth at microwave frequencies. The amplifiers are non-linear transmission lines, where the nonlinearity comes from the current dependence of the kinetic inductance. Amplification results from three and four-wave mixing processes, and phase matching over a wide frequency range is achieved by engineering the dispersion characteristics of the transmission line. Recent noise measurements over a wide frequency band demonstrate that the added noise of these amplifiers is close to one half photon, consistent with the quantum limit for a phase preserving amplifier. We will discuss applications of this class of amplifier to astronomical instruments.
Abstract Kinetic inductance travelling wave parametric amplifiers (KI-TWPAs) have been simulated using Keysight’s Advanced Design System. A lumped element representation of a superconducting transmission line has been developed using nonlinear inductor elements to represent the current dependency of the intrinsic kinetic inductance. This provides a fast, simple and easily modifiable method for analysing the parametric processes that occur in nonlinear kinetic inductance devices, such as parametric oscillators or amplifiers while also allowing the accompanying RF network to be optimised. This methodology is used to model the behaviour of a select number of KI-TWPA designs operating in the 3-wave mixing (3WM) and 4-wave mixing (4WM) regimes. S-parameters and dispersion properties are extracted from large signal S-parameter simulations, and the gain curve of each amplifier design is generated from harmonic balance simulations. The results are compared to the gain expression from the analytic solutions of the coupled mode equations while making reference to the gain curves of the equivalent KI-TWPAs from literature.
Background: Kinetic Inductance Travelling Wave Parametric Amplifiers (KITWPAs) are a variant of superconducting amplifier that can potentially achieve high gain with quantum-limited noise performance over broad bandwidth, which is important for many ultra-sensitive experiments. In this paper, we present a novel modelling technique that can better capture the electromagnetic behaviour of a KITWPA without the translation symmetry assumption, allowing us to flexibly explore the use of more complex transmission line structures and better predict their performance. Methods: In order to design a KITWPA with optimal performance, we investigate the use of different superconducting thin film materials, and compare their pros and cons in forming a high-gain low-loss medium feasible for amplification. We establish that if the film thickness can be controlled precisely, the material used has less impact on the performance of the device, as long as it is topologically defect-free and operating within its superconducting regime. With this insight, we propose the use of Titanium Nitride (TiN) film for our KITWPA as its critical temperature can be easily altered to suit our applications. We further investigate the topological effect of different commonly used superconducting transmission line structures with the TiN film, including the effect of various non-conducting materials required to form the amplifier. Results: Both of these comprehensive studies led us to two configurations of the KITWPA: 1) A low-loss 100 nm thick TiN coplanar waveguide amplifier, and 2) A compact 50 nm TiN inverted microstrip amplifier. We utilise the novel modelling technique described in the first part of the paper to explore and investigate the optimal design and operational setup required to achieve high gain with the broadest bandwidth for both KITWPAs, including the effect of loss. Conclusions: Finally, we conclude the paper with the actual layout and the predicted gain-bandwidth product of our KITWPAs.