Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Methods that improve high frequency Single Flux Quantum electronics design

Paul le Roux

Published Mar 1, 2021• 0 citations
OpenAlex

Abstract

ENGLISH ABSTRACT: In this thesis, we cover various methods that improve high-frequency Single Flux Quantum electronics design. Accurately modelling high-frequency effects is vital in high-frequency Single Flux Quantum electronics design. The passive transmission line is, currently, the most inaccurately modelled circuit component. We, therefore, developed a new 2D quasiTransverse-Magnetic method to calculate transmission line properties of superconductor structures. The new method can take into account quasi-particle losses as well as dielectric losses. The frequency response of a passive transmission line with arbitrary length can then readily be obtained from the transmission line properties. The high-frequency response is informative, but a time-domain simulation model is necessary to determine the effect on high-frequency circuit dynamics. Accordingly, we developed the Superconductor Vector Fitting algorithm so that we can take arbitrary superconductor frequency responses and convert them into time-domain simulation models. Complex dynamical behaviour, made more complicated by the new numerical simulation models, currently prohibits designing circuits by only using design equations. Automatic optimization routines are used to adjust circuit parameters to improve fabrication yield. Existing routines suffer from issues ranging from suboptimal circuits to severe performance issues. We developed a new and novel yield optimization algorithm, Distance-To-Failure-Maximization, that can be used to optimize superconductor circuits that are verified u sing time-domain simulations. High-frequency circuits can be sensitive to changes in bias current from parasitics mutual inductances. We developed the fundamental inductance model to model all inductive effects accurately. The fundamental inductance model can also be used to construct design equations which accounts for parasitic effects as well as reduce the number of unknowns in the yield optimization procedure. We use all the above methods in a detailed case study on the design of a JTLT. We take into account attenuation, impedance mismatch, flux mismatch, and resonance during the design of the JTLT circuit. With this, we conclude that the methods we developed have brought significant improvements to high-frequency Single Flux Quantum design.

Related papers

Accurate Small Signal Simulation of Superconductor Interconnects in SPICE

Paul le Roux, Coenrad Johann Fourie, Sasan Razmkhah +1 more

Superconductor electronics is gaining traction as the increasing density of integration of recent and future digital circuits pushes the limits of available simulation models. Designers often make assumptions in the behavioral models of circuit elements when simulating circuits. For instance high-frequency effects have been neglected so far in the design of superconductor digital circuits, while much has been done in the past to model them. Indeed these effects had little influence on the accuracy of digital circuits simulations until recently. The increase in clock frequency, combined with longer paths between cells and higher yield requirements for large scale circuits fabrication, has led to the need of more accurate models, including in particular high frequency effects such as quasi-particle losses. To do so, this work uses a state-space model that describes the circuit under study with internal state variables and a set of first-order differential equations. We extract the state-space model while analytically enforcing the DC requirements of superconductors that are required to account for flux-trapping. The model accurately traps flux at DC, and given the model is fitted with enough poles, the high-frequency effects are also accurate relative to the reference model. The high-frequency effects have been investigated on a practical circuit: a long-distance Passive Transmission Line (PTL) designed for the high-density MIT Lincoln Labs SFQ5ee process. Results obtained in the time domain allow to observe the effects of dispersion of pulses traveling on long paths of PTLs. Indeed the energy of voltage pulses is sufficient to break Cooper pairs for the highest clock frequencies.

IEEE Transactions on Applied Superconductivity•Apr 7, 2021•3 citations

VLSI complexity single flux quantum systems

Jabbari, Tahereh, Friedman, Eby G.

Superconductive electronics and, specifically, single flux quantum (SFQ) circuits are attracting significant attention as a promising ultra-low power and ultra-high speed circuit technology for beyond CMOS exascale supercomputing. Superconductive electronics is suitable for large scale, energy efficient, stationary cloud computing, ”big data” applications, and ultra-high speed neural networks. Significant development in the design and manufacture of superconductive electronics for prospective exascale computing systems has led to device densities exceeding 4.2×10^6 Josephson junctions (JJs) per cm2 – sufficient to enable large scale SFQ systems. The lack of electronic design automation (EDA) tools, however, is currently a serious issue affecting the development of complex SFQ circuits. Advances in EDA algorithms and design and analysis methodologies and techniques are therefore required to enhance the development of VLSI complexity SFQ systems. In this dissertation, issues and solutions to enable, connect, and secure VLSI complexity SFQ system are presented. Topics such as interconnects, ultra-high speed clocking and synchronization, signal interfaces, and deep scaling of superconductive structures are described, and related design methodologies, algorithms, circuits, and expressions are proposed. On-chip signal routing has become an issue of growing importance in modern VLSI complexity SFQ systems. Specialized routing methods for these systems are presented. The routing methods include passive transmission lines as global interconnect and Josephson transmission lines as local interconnect. Guidelines are provided for determining when to use global and local interconnects. Novel methodologies, algorithms, and expressions have been developed to manage resonance, flux trapping, and coupling in VLSI complexity SFQ circuits. The design of an SFQ clock distribution network is a challenging problem due to timing uncertainties at very high frequencies, gate-level pipelining, and fanout constraints. Near zero skew clock tree targeting large scale SFQ circuits is proposed to improve the global timing process while eliminating skew uncertainty. To enable higher fanout, area efficient splitter topologies are developed, producing a clock network suitable for large scale SFQ systems. All-JJ superconductive circuits based on bistable superconductor-ferromagnet-superconductor are presented to enable nanometer feature sizes for VLSI superconductive systems. These specialized guidelines, algorithms, and circuits enable deep scaling of superconductive systems for stationary high speed, ultra-low energy applications.

•Jan 1, 2023•0 citations

Design and implementation of a RSFQ superconductive digital electronics cell library

Rodwell S. Bakolo

ENGLISH ABSTRACT: Rapid Single Flux Quantum (RSFQ) cells are key in the design of complex and applicable RSFQ electronic circuits. These cells are low-level circuit elements that are used repeatedly to build larger, applicable RSFQ circuitry. Making these cells simple to layout and manufacture, but reliable for extensive use demands a careful development process for RSFQ cells. Cell functionality is verified through simulations, thereafter the cell is laid out in special software packages. Inductance of on-chip superconductor structures is extracted through careful modelling with numerical field solver software. A cell library has been developed by incorporating existing or published cells after further analysis and optimization, as well as developing new cells. Cells that have been adapted into the library include the Josephson transmission line (JTL), Splitter, Merger, D-Flip Flop (DFF), T-Flip Flop (TFF), NOT, AND, OR and XOR, DC-SFQ and SFQ-DC and PTL Driver and Receivers. New cells include NOR, NAND and XNOR. The cells were designed for the IPHT’s RSFQ1D 1kA/cmª and Hypres’ 4.5kA/cmª processes. The cells in the library have good bias current operating margins obtained through simulations (> ±26%). All cells have all the parameters listed in the thesis including extracted inductance values. In order to have a complete and verified RSFQ cell library, cells have been sent for fabrication at IPHT and Hypres facilities. These cells can now be tested on-chip, in the laboratory, to establish functionality and practical bias current margins. All test signal patterns and bias currents required for testing are defined to allow co-workers or collaborators to test the cells.

•Dec 1, 2011•1 citation

Design of Passive Transmission Line by Adjusting Intrinsic Parameters of Josephson Junctions

Xi Gao, Minghui Niu, Xiaoping Gao +5 more

Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum circuits by adjusting the Stewart McCumber parameter${\beta }_{\bm{C}}$of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from JJ's modified${\beta }_{\bm{C}}$on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. In total,$ \pm $30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.

IEEE Transactions on Applied Superconductivity•May 22, 2023•3 citations

The development and characterisation of a parameterised RSFQ cell library for layout synthesis

Lieze Schindler

ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.

•Mar 1, 2021•3 citations

A design approach to passive interconnects for single flux quantum logic circuits

Y. Hashimoto, Shinichi Yorozu, Y. Kameda +1 more

We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•53 citations
ENGLISH ABSTRACT: In this thesis, we cover various methods that improve high-frequency Single Flux Quantum electronics design. Accurately modelling high-frequency effects is vital in high-frequency Single Flux Quantum electronics design. The passive transmission line is, currently, the most inaccurately modelled circuit component. We, therefore, developed a new 2D quasiTransverse-Magnetic method to calculate transmission line properties of superconductor structures. The new method can take into account quasi-particle losses as well as dielectric losses. The frequency response of a passive transmission line with arbitrary length can then readily be obtained from the transmission line properties. The high-frequency response is informative, but a time-domain simulation model is necessary to determine the effect on high-frequency circuit dynamics. Accordingly, we developed the Superconductor Vector Fitting algorithm so that we can take arbitrary superconductor frequency responses and convert them into time-domain simulation models. Complex dynamical behaviour, made more complicated by the new numerical simulation models, currently prohibits designing circuits by only using design equations. Automatic optimization routines are used to adjust circuit parameters to improve fabrication yield. Existing routines suffer from issues ranging from suboptimal circuits to severe performance issues. We developed a new and novel yield optimization algorithm, Distance-To-Failure-Maximization, that can be used to optimize superconductor circuits that are verified u sing time-domain simulations. High-frequency circuits can be sensitive to changes in bias current from parasitics mutual inductances. We developed the fundamental inductance model to model all inductive effects accurately. The fundamental inductance model can also be used to construct design equations which accounts for parasitic effects as well as reduce the number of unknowns in the yield optimization procedure. We use all the above methods in a detailed case study on the design of a JTLT. We take into account attenuation, impedance mismatch, flux mismatch, and resonance during the design of the JTLT circuit. With this, we conclude that the methods we developed have brought significant improvements to high-frequency Single Flux Quantum design.
Superconductor electronics is gaining traction as the increasing density of integration of recent and future digital circuits pushes the limits of available simulation models. Designers often make assumptions in the behavioral models of circuit elements when simulating circuits. For instance high-frequency effects have been neglected so far in the design of superconductor digital circuits, while much has been done in the past to model them. Indeed these effects had little influence on the accuracy of digital circuits simulations until recently. The increase in clock frequency, combined with longer paths between cells and higher yield requirements for large scale circuits fabrication, has led to the need of more accurate models, including in particular high frequency effects such as quasi-particle losses. To do so, this work uses a state-space model that describes the circuit under study with internal state variables and a set of first-order differential equations. We extract the state-space model while analytically enforcing the DC requirements of superconductors that are required to account for flux-trapping. The model accurately traps flux at DC, and given the model is fitted with enough poles, the high-frequency effects are also accurate relative to the reference model. The high-frequency effects have been investigated on a practical circuit: a long-distance Passive Transmission Line (PTL) designed for the high-density MIT Lincoln Labs SFQ5ee process. Results obtained in the time domain allow to observe the effects of dispersion of pulses traveling on long paths of PTLs. Indeed the energy of voltage pulses is sufficient to break Cooper pairs for the highest clock frequencies.
Superconductive electronics and, specifically, single flux quantum (SFQ) circuits are attracting significant attention as a promising ultra-low power and ultra-high speed circuit technology for beyond CMOS exascale supercomputing. Superconductive electronics is suitable for large scale, energy efficient, stationary cloud computing, ”big data” applications, and ultra-high speed neural networks. Significant development in the design and manufacture of superconductive electronics for prospective exascale computing systems has led to device densities exceeding 4.2×10^6 Josephson junctions (JJs) per cm2 – sufficient to enable large scale SFQ systems. The lack of electronic design automation (EDA) tools, however, is currently a serious issue affecting the development of complex SFQ circuits. Advances in EDA algorithms and design and analysis methodologies and techniques are therefore required to enhance the development of VLSI complexity SFQ systems. In this dissertation, issues and solutions to enable, connect, and secure VLSI complexity SFQ system are presented. Topics such as interconnects, ultra-high speed clocking and synchronization, signal interfaces, and deep scaling of superconductive structures are described, and related design methodologies, algorithms, circuits, and expressions are proposed. On-chip signal routing has become an issue of growing importance in modern VLSI complexity SFQ systems. Specialized routing methods for these systems are presented. The routing methods include passive transmission lines as global interconnect and Josephson transmission lines as local interconnect. Guidelines are provided for determining when to use global and local interconnects. Novel methodologies, algorithms, and expressions have been developed to manage resonance, flux trapping, and coupling in VLSI complexity SFQ circuits. The design of an SFQ clock distribution network is a challenging problem due to timing uncertainties at very high frequencies, gate-level pipelining, and fanout constraints. Near zero skew clock tree targeting large scale SFQ circuits is proposed to improve the global timing process while eliminating skew uncertainty. To enable higher fanout, area efficient splitter topologies are developed, producing a clock network suitable for large scale SFQ systems. All-JJ superconductive circuits based on bistable superconductor-ferromagnet-superconductor are presented to enable nanometer feature sizes for VLSI superconductive systems. These specialized guidelines, algorithms, and circuits enable deep scaling of superconductive systems for stationary high speed, ultra-low energy applications.
ENGLISH ABSTRACT: Rapid Single Flux Quantum (RSFQ) cells are key in the design of complex and applicable RSFQ electronic circuits. These cells are low-level circuit elements that are used repeatedly to build larger, applicable RSFQ circuitry. Making these cells simple to layout and manufacture, but reliable for extensive use demands a careful development process for RSFQ cells. Cell functionality is verified through simulations, thereafter the cell is laid out in special software packages. Inductance of on-chip superconductor structures is extracted through careful modelling with numerical field solver software. A cell library has been developed by incorporating existing or published cells after further analysis and optimization, as well as developing new cells. Cells that have been adapted into the library include the Josephson transmission line (JTL), Splitter, Merger, D-Flip Flop (DFF), T-Flip Flop (TFF), NOT, AND, OR and XOR, DC-SFQ and SFQ-DC and PTL Driver and Receivers. New cells include NOR, NAND and XNOR. The cells were designed for the IPHT’s RSFQ1D 1kA/cmª and Hypres’ 4.5kA/cmª processes. The cells in the library have good bias current operating margins obtained through simulations (> ±26%). All cells have all the parameters listed in the thesis including extracted inductance values. In order to have a complete and verified RSFQ cell library, cells have been sent for fabrication at IPHT and Hypres facilities. These cells can now be tested on-chip, in the laboratory, to establish functionality and practical bias current margins. All test signal patterns and bias currents required for testing are defined to allow co-workers or collaborators to test the cells.
Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum circuits by adjusting the Stewart McCumber parameterβC{\beta }_{\bm{C}}βC​of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from JJ's modifiedβC{\beta }_{\bm{C}}βC​on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. In total,$ \pm $30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.