Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE MTT-S International Microwave Symposium digest

Superconductive digital instantaneous frequency-measurement subsystem

G.-C. Liang, Chuan‐Feng Shih, R.S. Withers, Ben Cole, Marie E. Johansson, L. P. Suppan

Published Dec 31, 2002• 2 citations
Publisher

Abstract

A 5-b high-temperature-superconductive digital instantaneous frequency-measurement (DIFM) subsystem has been constructed for the determination of the frequency of unknown signals over a 500-MHz bandwidth, centered on 4 GHz, with a resolution of +or-7.8 MHz. The subsystem contains a cryogenic section with five discriminator modules using superconductive delay lines, GaAs mixers, and power dividers. The subsystem also has a room-temperature GaAs limiting amplifier and a silicon postprocessor. With a single-tone CW (continuous-wave) input between-40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values.>

DOI
10.1109/mwsym.1993.276733

Related papers

Superconductive digital instantaneous frequency measurement subsystem

Guo‐Chun Liang, Chien-Fu Shih, R.S. Withers +3 more

A 5-b high-temperature-superconductive digital instantaneous frequency-measurement (DIFM) subsystem has been constructed for the determination of the frequency of unknown signals over a 500-MHz bandwidth, centered on 4 GHz, with a resolution of +or-7.8 MHz. The subsystem contains a cryogenic section with five discriminator modules using superconductive delay lines, GaAs mixers, and power dividers. The subsystem also has a room-temperature GaAs limiting amplifier and a silicon postprocessor. With a single-tone CW (continuous-wave) input between -40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values.>

IEEE Transactions on Microwave Theory and Techniques•Jan 1, 1993•35 citations

Superconductive digital instantaneous frequency-measurement subsystem

Guo‐Chun Liang, C. F. Shih, R.S. Withers +3 more

A five-bit high-temperature-superconductive digital instantaneous frequency-measurement (DIFM) subsystem has been constructed for the determination of the frequency of unknown signals over a 500 MHz bandwidth, centered on 4 GHz, with a resolution of +/- 7.8 MHz. The subsystem contains a cryogenic section with five discriminator modules utilizing superconductive delay lines, GaAs mixers, and power dividers. With a single-tone cw input between -40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values. This system demonstrates the potential system-level application of high-temperature superconductive electronics in instrumentation, communication, radar, and electronic warfare.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jan 4, 1994•1 citation

Space-qualified superconductive digital instantaneous frequency-measurement subsystem

Guo‐Chun Liang, Chien-Fu Shih, R.S. Withers +2 more

We have constructed a five-bit high temperature superconductive digital instantaneous frequency measurement (DIFM) subsystem capable of determining the frequency of unknown signals over a 500-MHz bandwidth, centered on 4 GHz, with a resolution of 17.8 MHz. The system consists of three parts: a limiting amplifier and filter, a comparator and data processing unit operating at room temperature, and a cryogenic subsystem containing five discriminator modules based on superconductive delay lines, GaAs mixers and power dividers. With a single-tone CW input between -40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values. This system was built for the High-Temperature Superconductor Space Experiment, Phase II (HTSSE II). It has passed all required qualification tests for vibration, shock and thermal cycling. The system is currently scheduled for satellite launch in fall 1996. Compared to a conventional system, the superconductive version of the DIFM is considerably smaller and provides enhanced resolution. In addition, the technology employed can be readily extended to a system with additional bits and wider instantaneous bandwidth. The system built demonstrates the potential for system-level applications of high-temperature superconductive electronics in instrumentation, communications, radar, and electronic warfare.

IEEE Transactions on Microwave Theory and Techniques•Jul 1, 1996•44 citations

Superconductive chirp-transform spectrum analyzer

R.S. Withers, Stanley A. Reible

Spectral analysis over an instantaneous bandwidth of 2.4 GHz has been demonstrated utilizing superconductive dispersive delay lines in a chirp-transform configuration. Two-tone resolution of 43 MHz and ±1.2-dB amplitude uniformity were achieved.

IEEE Electron Device Letters•Jun 1, 1985•9 citations

Superconducting bandpass ΔΣ modulator with 2.23-GHz center frequency and 42.6-GHz sampling rate

John F. Bulzacchelli, Hae-Seung Lee, James A. Misewich +1 more

This paper presents a superconducting bandpass /spl Delta//spl Sigma/ modulator for direct analog-to-digital conversion of radio frequency signals in the gigahertz range. The design, based on a 2.23-GHz microstrip resonator and a single flux quantum comparator, exploits several advantages of superconducting electronics: the high quality factor of resonators, the fast switching speed of the Josephson junction, natural quantization of voltage pulses, and high circuit sensitivity. The modulator test chip includes an integrated acquisition memory for capturing output data at sampling rates up to 45 GHz. The small size (256 b) of the acquisition memory limits the frequency resolution of spectra based on standard fast Fourier transforms. Output spectra with enhanced resolution are obtained with a segmented correlation method. At a 42.6-GHz sampling rate, the measured SNR is 49 dB over a 20.8-MHz bandwidth, and a full-scale (FS) input is -17.4 dBm. At a 40.2-GHz sampling rate, the measured in-band noise is -57 dBFS over a 19.6-MHz bandwidth. The modulator test chip contains 4065 Josephson junctions and dissipates 1.9 mW at T=4.2 K.

IEEE Journal of Solid-State Circuits•Dec 1, 2002•21 citations

High-resolution microwave frequency identification via bias-tuned superconducting transmission lines

Masato Naruse, Kohta Yamaguchi, Hiroaki Myoren

We develop a microwave frequency counter based on the complex conductivity modulation of a DC-biased superconducting transmission line while maintaining the bias below the critical current. A resonator-free platform is proposed for microwave frequency estimation. It utilizes a bias-controlled phase delay in a superconducting coplanar waveguide structure, which imprints frequency-dependent signatures on the transmitted microwave tone. Instead of relying on intentionally designed resonators, our method leverages the complex transmission spectra arising from numerous weak resonance structures due to subtle fabrication imperfections. However, even in the absence of such features, the method remains effective because the DC bias induces frequency-dependent phase shifts that modulate the microwave signal’s propagation velocity. Mixed signals are externally generated via in-phase-quadrature mixing with a reference signal, which manifests as interference-like patterns enabling high-resolution spectral identification. We measure the frequency-dependent changes in the interference-like patterns under this bias to catalog characteristic transmission loss profiles across a wide frequency range (2–8 GHz). These profiles serve as supervised training data for a machine learning algorithm that identifies unknown input microwave frequencies with high-resolution and accuracy. Our method achieves a frequency resolution (F/ΔF) of over 200 000 and a relative error in identification of below 0.01%. This scalable approach to distributed microwave sensing may be useful for quantum measurement and signal classification and is particularly well-suited for dark matter searches, such as hidden-photon detection, where broadband frequency identification without prior tuning is essential. The measured frequency range is primarily limited by the bandwidth of external microwave components, such as low-noise amplifiers and bias-tees. The superconducting device itself may be used up to its superconducting gap frequency (∼280 GHz for TiN at 3.8 K).

AIP Advances•Nov 1, 2025•0 citations
A 5-b high-temperature-superconductive digital instantaneous frequency-measurement (DIFM) subsystem has been constructed for the determination of the frequency of unknown signals over a 500-MHz bandwidth, centered on 4 GHz, with a resolution of +or-7.8 MHz. The subsystem contains a cryogenic section with five discriminator modules using superconductive delay lines, GaAs mixers, and power dividers. The subsystem also has a room-temperature GaAs limiting amplifier and a silicon postprocessor. With a single-tone CW (continuous-wave) input between-40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values.>
A 5-b high-temperature-superconductive digital instantaneous frequency-measurement (DIFM) subsystem has been constructed for the determination of the frequency of unknown signals over a 500-MHz bandwidth, centered on 4 GHz, with a resolution of +or-7.8 MHz. The subsystem contains a cryogenic section with five discriminator modules using superconductive delay lines, GaAs mixers, and power dividers. The subsystem also has a room-temperature GaAs limiting amplifier and a silicon postprocessor. With a single-tone CW (continuous-wave) input between -40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values.>
A five-bit high-temperature-superconductive digital instantaneous frequency-measurement (DIFM) subsystem has been constructed for the determination of the frequency of unknown signals over a 500 MHz bandwidth, centered on 4 GHz, with a resolution of +/- 7.8 MHz. The subsystem contains a cryogenic section with five discriminator modules utilizing superconductive delay lines, GaAs mixers, and power dividers. With a single-tone cw input between -40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values. This system demonstrates the potential system-level application of high-temperature superconductive electronics in instrumentation, communication, radar, and electronic warfare.
We have constructed a five-bit high temperature superconductive digital instantaneous frequency measurement (DIFM) subsystem capable of determining the frequency of unknown signals over a 500-MHz bandwidth, centered on 4 GHz, with a resolution of 17.8 MHz. The system consists of three parts: a limiting amplifier and filter, a comparator and data processing unit operating at room temperature, and a cryogenic subsystem containing five discriminator modules based on superconductive delay lines, GaAs mixers and power dividers. With a single-tone CW input between -40 dBm and +10 dBm, the frequency quantization boundaries of the subsystem are, on average, 3.1 MHz from their design values. This system was built for the High-Temperature Superconductor Space Experiment, Phase II (HTSSE II). It has passed all required qualification tests for vibration, shock and thermal cycling. The system is currently scheduled for satellite launch in fall 1996. Compared to a conventional system, the superconductive version of the DIFM is considerably smaller and provides enhanced resolution. In addition, the technology employed can be readily extended to a system with additional bits and wider instantaneous bandwidth. The system built demonstrates the potential for system-level applications of high-temperature superconductive electronics in instrumentation, communications, radar, and electronic warfare.
This paper presents a superconducting bandpass /spl Delta//spl Sigma/ modulator for direct analog-to-digital conversion of radio frequency signals in the gigahertz range. The design, based on a 2.23-GHz microstrip resonator and a single flux quantum comparator, exploits several advantages of superconducting electronics: the high quality factor of resonators, the fast switching speed of the Josephson junction, natural quantization of voltage pulses, and high circuit sensitivity. The modulator test chip includes an integrated acquisition memory for capturing output data at sampling rates up to 45 GHz. The small size (256 b) of the acquisition memory limits the frequency resolution of spectra based on standard fast Fourier transforms. Output spectra with enhanced resolution are obtained with a segmented correlation method. At a 42.6-GHz sampling rate, the measured SNR is 49 dB over a 20.8-MHz bandwidth, and a full-scale (FS) input is -17.4 dBm. At a 40.2-GHz sampling rate, the measured in-band noise is -57 dBFS over a 19.6-MHz bandwidth. The modulator test chip contains 4065 Josephson junctions and dissipates 1.9 mW at T=4.2 K.
We develop a microwave frequency counter based on the complex conductivity modulation of a DC-biased superconducting transmission line while maintaining the bias below the critical current. A resonator-free platform is proposed for microwave frequency estimation. It utilizes a bias-controlled phase delay in a superconducting coplanar waveguide structure, which imprints frequency-dependent signatures on the transmitted microwave tone. Instead of relying on intentionally designed resonators, our method leverages the complex transmission spectra arising from numerous weak resonance structures due to subtle fabrication imperfections. However, even in the absence of such features, the method remains effective because the DC bias induces frequency-dependent phase shifts that modulate the microwave signal’s propagation velocity. Mixed signals are externally generated via in-phase-quadrature mixing with a reference signal, which manifests as interference-like patterns enabling high-resolution spectral identification. We measure the frequency-dependent changes in the interference-like patterns under this bias to catalog characteristic transmission loss profiles across a wide frequency range (2–8 GHz). These profiles serve as supervised training data for a machine learning algorithm that identifies unknown input microwave frequencies with high-resolution and accuracy. Our method achieves a frequency resolution (F/ΔF) of over 200 000 and a relative error in identification of below 0.01%. This scalable approach to distributed microwave sensing may be useful for quantum measurement and signal classification and is particularly well-suited for dark matter searches, such as hidden-photon detection, where broadband frequency identification without prior tuning is essential. The measured frequency range is primarily limited by the bandwidth of external microwave components, such as low-noise amplifiers and bias-tees. The superconducting device itself may be used up to its superconducting gap frequency (∼280 GHz for TiN at 3.8 K).