Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Emerging materials for superconducting nanowire photon counting arrays

Umberto Nasti

Published Jan 1, 2020• 0 citations
Publisher

Abstract

Superconducting nanowire single-photon detectors (SNSPDs) are the leading technology for low noise, high efficiency infrared single-photon detection. The basic SNSPD consists of a nanowire patterned in an ultrathin superconducting thin film, which is cooled below its critical temperature and biased close to its critical current. The absorption of a single-photon creates a resistive region, triggering a fast output voltage pulse which can be readily amplified and registered. The excellent performance of SNSPDs at near-infrared and telecommunications wavelengths has led to their adoption in important applications such as quantum secure communications, single-photon spectroscopy and single-photon LIDAR. A clear challenge for the SNSPD community is to extend the spectral range of SNSPDs into the mid infrared, and to improve material uniformity to enable the realization of large area arrays for multimode or free space coupling. The aim of this work is to evaluate potential materials for next generation mid-infrared SNSPD arrays. In this work, thin films of polycrystalline NbN and amorphous MoSi have been optimized to test the uniformity of a multipixel array configuration composed of 8 nanowire meander structures covering 10 um x 10 um area, 100 nm width and 50% filling factor. The 8-pixels SNSPD arrays have been patterned on 8 nm thickness NbN grown on high resistivity silicon (HR Si) substrate at room temperature and at 800 °C exhibiting respectively 4.4 K and 7.3 K as mean critical temperature across the pixels. The 8- pixels SNSPD array patterned on 8 nm thickness MoSi cooling the HR Si substrate to -180 °C has exhibited a mean critical temperature of 3.2 K across the pixels. Optical properties have been measured by an attenuated 1550 nm laser diode source delivered by single mode optical fibre at a controlled distance from the chip in order to broadly illuminate the array. The optical properties have been studied only for the 8 nm thickness NbN SNSPD array grown at room temperature has demonstrated uniform optical properties across pixels exhibiting similar saturation of the internal efficiency over a large bias, similar dark count rate and similar timing jitter (about 137 ps) across pixels. In the single photon regime at 1550 nm, pixels 4 and 6 of the 8 nm thickness NbN SNSPD array exhibit 28.4% and 4.7% pixel detection efficiency as measured at the bias current 95% of their respective critical current at 2.2 K.

DOI
10.5525/gla.thesis.81517

Related papers

Next generation superconducting nanowire single-photon detectors

Kleanthis Erotokritou

Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.

•Jan 1, 2019•0 citations

Superconducting nanowire materials for mid infrared single photon detection (Conference Presentation)

D. Morozov, Archan Banerjee, Kleanthis Erotokritou +5 more

Superconducting nanowire single photon detectors (SNSPD) offer excellent performance for infrared single photon detection, combining high efficiency, low timing jitter, low dark count rates and high photon counting rates. Promising application areas for SNSPDs include quantum key distribution, space-to-ground communications and single photon remote sensing [1]. SNSPDs are typically made with ultrathin niobium nitride (NbN) films with thickness 4 nm and a superconducting transition temperature above 9 K. NbN offers high performance in the near infrared but their sensitivity drops at wavelengths beyond 2 um. There is growing interest in potential photon counting applications in the mid infrared domain (for example remote sensing of greenhouse gases in the atmosphere [2]). One way to overcome the wavelength limit in NbN SNSPDs is to use films with a lower superconducting energy gap [3]. Here we report on the study of SNSPDs fabricated with thin films of titanium nitride (TiN). We compare TiN films deposited by atomic layer deposition (ALD) and by magnetron sputtering. The TiN films range in thickness from 5 to 60 nm, with superconducting transition temperatures from ~1 K to 3.5 K. We have analyzed the films via transmission electron microscopy and variable angle spectroscopic ellipsometry. We characterize TiN SNSPDs performance from near to mid-infrared at wavelengths (1-4 um) with fast optical parametric oscillator (OPO) source. We compare the performance of TiN SNSPDs to devices based on other lower gap materials: MoSi, NbTiN, WSi. [1] Natarajan et al Superconductor Science and Technology 25 063001 (2012) [2] Abshire et al Laser Applications to Chemical, Security and Environmental Analysis, (Optical Society of America, 2008) paper LMA4 [3] Verma et al Applied Physics Letters 105 022602 (2014)

Advanced Photon Counting Techniques•May 14, 2018•3 citations

Bias sputtered NbN and superconducting nanowire devices

Andrew E. Dane, Adam N. McCaughan, Di Zhu +6 more

Superconducting nanowire single photon detectors (SNSPDs) promise to combine near-unity quantum efficiency with >100 megacounts per second rates, picosecond timing jitter, and sensitivity ranging from x-ray to mid-infrared wavelengths. However, this promise is not yet fulfilled, as superior performance in all metrics is yet to be combined into one device. The highest single-pixel detection efficiency and the widest bias windows for saturated quantum efficiency have been achieved in SNSPDs based on amorphous materials, while the lowest timing jitter and highest counting rates were demonstrated in devices made from polycrystalline materials. Broadly speaking, the amorphous superconductors that have been used to make SNSPDs have higher resistivities and lower critical temperature (Tc) values than typical polycrystalline materials. Here, we demonstrate a method of preparing niobium nitride (NbN) that has lower-than-typical superconducting transition temperature and higher-than-typical resistivity. As we will show, NbN deposited onto unheated SiO2 has a low Tc and high resistivity but is too rough for fabricating unconstricted nanowires, and Tc is too low to yield SNSPDs that can operate well at liquid helium temperatures. By adding a 50 W RF bias to the substrate holder during sputtering, the Tc of the unheated NbN films was increased by up to 73%, and the roughness was substantially reduced. After optimizing the deposition for nitrogen flow rates, we obtained 5 nm thick NbN films with a Tc of 7.8 K and a resistivity of 253 μΩ cm. We used this bias sputtered room temperature NbN to fabricate SNSPDs. Measurements were performed at 2.5 K using 1550 nm light. Photon count rates appeared to saturate at bias currents approaching the critical current, indicating that the device's quantum efficiency was approaching unity. We measured a single-ended timing jitter of 38 ps. The optical coupling to these devices was not optimized; however, integration with front-side optical structures to improve absorption should be straightforward. This material preparation was further used to fabricate nanocryotrons and a large-area imager device, reported elsewhere. The simplicity of the preparation and promising device performance should enable future high-performance devices.

Applied Physics Letters•Sep 18, 2017•67 citations

Single-photon and photon-number-resolving detectors based on superconducting nanowires

Francesco Marsili

Nanowire superconducting single photon detectors (SSPDs) [1] are characterized by very high sensitivity in the near infrared (detection efficiency η up to 30%, for a dark count rate DK of few Hz), speed (up to ∼1 GHz repetition rate) and time resolution (jitter of 20 ps full width at half maximum, FWHM). They can be operated at temperatures near 4 K, so they can be packaged in cryogenic dipsticks or cryogen-free refrigerators. These features make SSPDs the most promising detectors for telecom-wavelength single-photon counting applications. The basic structure of an SSPD is a narrow (w=50 to 120 nm), thin (th∼4-10 nm) NbN superconducting nanowire folded in a meander pattern. The typical detector active area (i.e. the size of the pixel) is Ad=10 × 10 µm2 (which allows an efficient coupling with the core of optical fibers at telecom wavelengths) with filling factor (f, the ratio of the area occupied by the superconducting meander to the device total area) ranging from 40% to 60%. The meanders are embedded in a 50 Ω coplanar transmission line. At present, the SSPD detection efficiency is limited by its absorbance (α, the ratio of the number of photons absorbed in the nanowire to the number of incident photons on the device active area). Indeed, it has been shown that in the classic front-illumination configuration α cannot exceed 30%. Our approach to increase α consists in integrating SSPDs with advanced optical structures such as distributed Bragg reflectors (DBRs) and optical waveguides. This requires to transfer the challenging SSPD technology (i.e. the deposition of high-quality few-nm thick NbN films and the nano-patterning by electron beam lithography, EBL) from the usual comfortable substrates, i.e. sapphire and MgO, which are known to allow the deposition of few-nm thick NbN films of excellent quality, to an optical substrate like GaAs, on which DBRs and waveguides can be easily obtained. Our first task was then to optimize a process for the deposition of high-quality few-nm thick NbN films on GaAs and AlAs/GaAs-based DBRs. Because of the requirement of compatibility with GaAs, the substrate temperature used for the depositions is 400°C, in order to prevent As evaporation. As GaAs and DBRs are highly mismatched substrates, the deposition parameters were first optimized with respect to the superconducting properties of NbN films on MgO substrates, which allow the growth of high crystal quality NbN films at low temperature. This made easier to separate the influence of stoichiometry from that of microstructure. The optimized deposition parameters were then used to grow NbN films on GaAs and DBRs, under the reasonable assumption (later checked and confirmed) that changing the substrate would not produce a change in film stoichiometry, but only in its microstructure. NbN films ranging from 150nm to 3nm in thickness were then deposited on epitaxial-quality single crystal MgO, GaAs and DBRs structures. The deposition technique is the current controlled DC magnetron sputtering (planar, circular, balanced configuration) of Nb in an Ar + N2 plasma. NbN films deposited on MgO exhibit superconducting critical temperature ΤC=10 Κ, superconducting transition width ΔΤC=0.8 Κ and residual resistivity ratio RRR=R(20K)/R(300K)=0.8 for th=4 nm, which are state of the art values, proof of the excellent quality of our low-temperature deposition process. The quality of films deposited on GaAs and on DBRs is lower than that of NbN deposited on MgO, as for any thickness they systematically exhibit higher ΔΤC and lower ΤC and RRR. However, 5.5 nm-thick NbN films on GaAs still exhibit ΤC=10.7 Κ, ΔΤC=1.1 Κ and RRR=0.7, which compares with 4.5 nm thick films on MgO, making them suitable for device fabrication. To our knowledge, the growth of such high quality thin NbN films on GaAs and DBRs, has never been reported in literature. The degradation of the superconducting properties exhibited by NbN films on GaAs and DBRs was attributed to a highly defected microstructure, due both to a higher lattice misfit between NbN and GaAs and to a poorer quality of the substrate surface. Encouraging preliminary results show that the quality of these films can be improved either cleaning the GaAs/DBR substrate surface more effectively or adding an MgO buffer layer. SSPDs were fabricated on thin NbN films (th=3-7 nm) deposited under optimal conditions on MgO and GaAs by EBL and reactive ion etching. The geometrical parameters of our detectors are: Ad=5×5 µm2, w=60-200 nm, f=40%-60%. The devices were then characterized both electrically and optically. I-V curves of test structures were measured, from which it was possible to deduce important physical parameters used as figures of merit to estimate the superconducting properties of the nanowires, or for the design and the simulation of the devices. The quality of the devices fabricated on GaAs is poorer than those on MgO, most likely due to the lower quality of NbN films deposited on GaAs and to issues related to the EBL nano-patterning step. Measurements of η and of DK as a function of the bias current were performed on SSPDs fabricated on MgO and GaAs. The best performance was exhibited by a w=100 nm, f=40%, th=4 nm meander, showing η=20% and noise equivalent power NEP=10-16 W/Hz1/2 (at λ=1.3 µm and T=4.2 K), which are state of the art values. This result showed for the first time that high performance NbN SSPDs can be realized on a different substrate and from a deposition process at lower temperature than previously reported. High detection efficiencies could not be measured with SSPDs fabricated on GaAs, but it should be noted that at present only first-generation devices (fabricated on GaAs substrates of poor surface quality) have been tested. Better results are expected from devices fabricated on the improved NbN films grown on clean or MgO-buffered GaAs substrates. Although SSPDs on MgO have shown high detection efficiency, the fabrication yield of high performance detectors has to be improved. Variations of the critical current along a nanowire are responsible for the wide distribution in efficiency values of nominally identical SSPDs. In order to understand the physical origin of the nanowire constrictions (i.e. regions of suppressed superconductivity) we performed a spatially-resolved characterization of η of a long straight nanowire, followed by a high resolution SEM (scanning electron microscope) scan on its whole length. Two types of inhomogeneities were evidenced, corresponding to localized efficiency dips and peaks. The peaks likely correspond to constrictions. SEM observations did not evidence any width narrowing at the position of the efficiency peaks, which suggests that constrictions might be due to thickness or quality inhomogeneities of the film occurring during the film deposition or later in the process. On the other hand, the efficiency dips have been correlated with lithography problems discovered on SEM images. Finally, a new photon number resolving detector, the Parallel Nanowire Detector (PND), has been demonstrated, which significantly outperforms existing approaches in terms of sensitivity, speed and multiplication noise in the telecommunication wavelength range. In particular, it provides a repetition rate (80 MHz) three orders of magnitude larger than any existing detector at telecom wavelength, and a sensitivity (NEP=4.2×10-18 W/Hz1/2) one-two orders of magnitude better, with the exception of transition-edge sensors (which require a much lower operating temperature). An electrical equivalent model of the device was developed in order to study its operation. The modeling predicts a physical limit to the reset time of the PND, which is lower than initially estimated. Furthermore, the figures of merit of the device performance in terms of efficiency, speed and sensitivity were defined and their dependency on the design parameters analyzed. Additionally, we developed modeling tools to fully characterize the device and an algorithm to estimate the photon number statistics of an unknown light using the PND. The reconstruction proved to be successful only for low photon fluxes, most likely due to the limited counting capability and the poor calibration of the detector. The PND, with its high repetition rate and high sensitivity, is then suitable for measuring an unknown photon number probability distribution assuming accurate calibration and sufficient counting capability. ______________________________[1] G. N. Gol'tsman, O. Okunev, G. Chulkova, A. Lipatov, A. Semenov, K. Smirnov, B. Voronov, A. Dzardanov, C. Williams, and R. Sobolewski, Appl. Phys. Lett. 79, 705 (2001).

•Jan 1, 2009•4 citations

Single-photon detection in few-layer NbSe2 superconducting nanowires

Lucio Zugliani, Alessandro Palermo, Bianca Scaparra +11 more

Abstract Superconducting Nanowire Single-Photon Detectors (SNSPDs) are key building blocks for photonic quantum technologies due to their ability to detect single photons with ultra-high efficiency, low dark counts and fast temporal resolution. Superconducting materials exhibiting high uniformity, large absorption cross-section and atomic-scale thickness are desirable to extend single-photon detection from the near-infrared up to the terahertz regime, where existing material choices are especially constrained. Substrate independence would further open the way to integrating detectors onto functional materials and heterostructures, enhancing performance and enabling proximal readout of a wide range of individual excitations. Here, we pattern the prototypical two-dimensional superconductor niobium diselenide (NbSe 2 ) into few-layer nanowires less than 100 nm wide and demonstrate single-photon detection at 780 nm and 1550 nm. At the same time, the dark-count rate remains below 1 Hz up to the switching current and we achieve a timing jitter below 50 ps. We estimate via a diffusive hot-spot model that materials and geometric parameters would allow a theoretical cut-off wavelength in the millimetre range, assuming state-of-the-art device parameters. Our results open up routes toward quantum-limited detectors integrated into quantum-photonic circuits and quantum devices, with the potential for novel detection capabilities and unprecedented energy sensitivity.

arXiv:2508.18843•Nature Communications•Jul 29, 2026•1 citation

Atomic-layer deposited mid-infrared sensitive NbTiN superconducting nanowire single photon detectors

Nidhi Choudhary, Dmitry Morozov, Daniel Kuznesof +7 more

Abstract The advancement of superconducting nanowire single-photon detectors (SNSPDs or SSPDs) is intrinsically linked to breakthroughs in superconducting materials engineering. These detectors are prized for their excellent sensitivity and performance across a wide wavelength range, from ultra-violet to mid-infrared (mid-IR). Plasma-enhanced atomic layer deposition (ALD) is an advanced deposition technique that enables exceptional film uniformity across large wafers, making it ideal for a variety of applications. In this study, ALD NbTiN films are fabricated into SNSPDs that exhibit single-photon response across near- to mid-IR wavelengths. A 5 nm thick NbTiN film was patterned into devices consisting of ∼100 nm wide meandered nanowires, and the nanowire cross-section and composition were analysed by transmission electron microscopy. The devices were tested in a closed-cycle cryostat with a base temperature of 0.9 K. Photon detection rate and timing jitter were measured across the wavelength range 1.5–4.4 µ m under low dark count conditions, confirming single-photon sensitivity across the measured wavelength bands. This work introduces the ALD-grown NbTiN films as a new platform for SNSPD detectors, achieving mid-IR single-photon sensitivity. The intact film quality after fabrication demonstrates the potential of ALD processes for scalable infrared detector technologies.

Superconductor Science and Technology•Apr 1, 2026•1 citation
Superconducting nanowire single-photon detectors (SNSPDs) are the leading technology for low noise, high efficiency infrared single-photon detection. The basic SNSPD consists of a nanowire patterned in an ultrathin superconducting thin film, which is cooled below its critical temperature and biased close to its critical current. The absorption of a single-photon creates a resistive region, triggering a fast output voltage pulse which can be readily amplified and registered. The excellent performance of SNSPDs at near-infrared and telecommunications wavelengths has led to their adoption in important applications such as quantum secure communications, single-photon spectroscopy and single-photon LIDAR. A clear challenge for the SNSPD community is to extend the spectral range of SNSPDs into the mid infrared, and to improve material uniformity to enable the realization of large area arrays for multimode or free space coupling. The aim of this work is to evaluate potential materials for next generation mid-infrared SNSPD arrays. In this work, thin films of polycrystalline NbN and amorphous MoSi have been optimized to test the uniformity of a multipixel array configuration composed of 8 nanowire meander structures covering 10 um x 10 um area, 100 nm width and 50% filling factor. The 8-pixels SNSPD arrays have been patterned on 8 nm thickness NbN grown on high resistivity silicon (HR Si) substrate at room temperature and at 800 °C exhibiting respectively 4.4 K and 7.3 K as mean critical temperature across the pixels. The 8- pixels SNSPD array patterned on 8 nm thickness MoSi cooling the HR Si substrate to -180 °C has exhibited a mean critical temperature of 3.2 K across the pixels. Optical properties have been measured by an attenuated 1550 nm laser diode source delivered by single mode optical fibre at a controlled distance from the chip in order to broadly illuminate the array. The optical properties have been studied only for the 8 nm thickness NbN SNSPD array grown at room temperature has demonstrated uniform optical properties across pixels exhibiting similar saturation of the internal efficiency over a large bias, similar dark count rate and similar timing jitter (about 137 ps) across pixels. In the single photon regime at 1550 nm, pixels 4 and 6 of the 8 nm thickness NbN SNSPD array exhibit 28.4% and 4.7% pixel detection efficiency as measured at the bias current 95% of their respective critical current at 2.2 K.
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.
Superconducting nanowire single photon detectors (SNSPD) offer excellent performance for infrared single photon detection, combining high efficiency, low timing jitter, low dark count rates and high photon counting rates. Promising application areas for SNSPDs include quantum key distribution, space-to-ground communications and single photon remote sensing [1]. SNSPDs are typically made with ultrathin niobium nitride (NbN) films with thickness 4 nm and a superconducting transition temperature above 9 K. NbN offers high performance in the near infrared but their sensitivity drops at wavelengths beyond 2 um. There is growing interest in potential photon counting applications in the mid infrared domain (for example remote sensing of greenhouse gases in the atmosphere [2]). One way to overcome the wavelength limit in NbN SNSPDs is to use films with a lower superconducting energy gap [3]. Here we report on the study of SNSPDs fabricated with thin films of titanium nitride (TiN). We compare TiN films deposited by atomic layer deposition (ALD) and by magnetron sputtering. The TiN films range in thickness from 5 to 60 nm, with superconducting transition temperatures from ~1 K to 3.5 K. We have analyzed the films via transmission electron microscopy and variable angle spectroscopic ellipsometry. We characterize TiN SNSPDs performance from near to mid-infrared at wavelengths (1-4 um) with fast optical parametric oscillator (OPO) source. We compare the performance of TiN SNSPDs to devices based on other lower gap materials: MoSi, NbTiN, WSi. [1] Natarajan et al Superconductor Science and Technology 25 063001 (2012) [2] Abshire et al Laser Applications to Chemical, Security and Environmental Analysis, (Optical Society of America, 2008) paper LMA4 [3] Verma et al Applied Physics Letters 105 022602 (2014)
Superconducting nanowire single photon detectors (SNSPDs) promise to combine near-unity quantum efficiency with >100 megacounts per second rates, picosecond timing jitter, and sensitivity ranging from x-ray to mid-infrared wavelengths. However, this promise is not yet fulfilled, as superior performance in all metrics is yet to be combined into one device. The highest single-pixel detection efficiency and the widest bias windows for saturated quantum efficiency have been achieved in SNSPDs based on amorphous materials, while the lowest timing jitter and highest counting rates were demonstrated in devices made from polycrystalline materials. Broadly speaking, the amorphous superconductors that have been used to make SNSPDs have higher resistivities and lower critical temperature (Tc) values than typical polycrystalline materials. Here, we demonstrate a method of preparing niobium nitride (NbN) that has lower-than-typical superconducting transition temperature and higher-than-typical resistivity. As we will show, NbN deposited onto unheated SiO2 has a low Tc and high resistivity but is too rough for fabricating unconstricted nanowires, and Tc is too low to yield SNSPDs that can operate well at liquid helium temperatures. By adding a 50 W RF bias to the substrate holder during sputtering, the Tc of the unheated NbN films was increased by up to 73%, and the roughness was substantially reduced. After optimizing the deposition for nitrogen flow rates, we obtained 5 nm thick NbN films with a Tc of 7.8 K and a resistivity of 253 μΩ cm. We used this bias sputtered room temperature NbN to fabricate SNSPDs. Measurements were performed at 2.5 K using 1550 nm light. Photon count rates appeared to saturate at bias currents approaching the critical current, indicating that the device's quantum efficiency was approaching unity. We measured a single-ended timing jitter of 38 ps. The optical coupling to these devices was not optimized; however, integration with front-side optical structures to improve absorption should be straightforward. This material preparation was further used to fabricate nanocryotrons and a large-area imager device, reported elsewhere. The simplicity of the preparation and promising device performance should enable future high-performance devices.
Nanowire superconducting single photon detectors (SSPDs) [1] are characterized by very high sensitivity in the near infrared (detection efficiency η up to 30%, for a dark count rate DK of few Hz), speed (up to ∼1 GHz repetition rate) and time resolution (jitter of 20 ps full width at half maximum, FWHM). They can be operated at temperatures near 4 K, so they can be packaged in cryogenic dipsticks or cryogen-free refrigerators. These features make SSPDs the most promising detectors for telecom-wavelength single-photon counting applications. The basic structure of an SSPD is a narrow (w=50 to 120 nm), thin (th∼4-10 nm) NbN superconducting nanowire folded in a meander pattern. The typical detector active area (i.e. the size of the pixel) is Ad=10 × 10 µm2 (which allows an efficient coupling with the core of optical fibers at telecom wavelengths) with filling factor (f, the ratio of the area occupied by the superconducting meander to the device total area) ranging from 40% to 60%. The meanders are embedded in a 50 Ω coplanar transmission line. At present, the SSPD detection efficiency is limited by its absorbance (α, the ratio of the number of photons absorbed in the nanowire to the number of incident photons on the device active area). Indeed, it has been shown that in the classic front-illumination configuration α cannot exceed 30%. Our approach to increase α consists in integrating SSPDs with advanced optical structures such as distributed Bragg reflectors (DBRs) and optical waveguides. This requires to transfer the challenging SSPD technology (i.e. the deposition of high-quality few-nm thick NbN films and the nano-patterning by electron beam lithography, EBL) from the usual comfortable substrates, i.e. sapphire and MgO, which are known to allow the deposition of few-nm thick NbN films of excellent quality, to an optical substrate like GaAs, on which DBRs and waveguides can be easily obtained. Our first task was then to optimize a process for the deposition of high-quality few-nm thick NbN films on GaAs and AlAs/GaAs-based DBRs. Because of the requirement of compatibility with GaAs, the substrate temperature used for the depositions is 400°C, in order to prevent As evaporation. As GaAs and DBRs are highly mismatched substrates, the deposition parameters were first optimized with respect to the superconducting properties of NbN films on MgO substrates, which allow the growth of high crystal quality NbN films at low temperature. This made easier to separate the influence of stoichiometry from that of microstructure. The optimized deposition parameters were then used to grow NbN films on GaAs and DBRs, under the reasonable assumption (later checked and confirmed) that changing the substrate would not produce a change in film stoichiometry, but only in its microstructure. NbN films ranging from 150nm to 3nm in thickness were then deposited on epitaxial-quality single crystal MgO, GaAs and DBRs structures. The deposition technique is the current controlled DC magnetron sputtering (planar, circular, balanced configuration) of Nb in an Ar + N2 plasma. NbN films deposited on MgO exhibit superconducting critical temperature ΤC=10 Κ, superconducting transition width ΔΤC=0.8 Κ and residual resistivity ratio RRR=R(20K)/R(300K)=0.8 for th=4 nm, which are state of the art values, proof of the excellent quality of our low-temperature deposition process. The quality of films deposited on GaAs and on DBRs is lower than that of NbN deposited on MgO, as for any thickness they systematically exhibit higher ΔΤC and lower ΤC and RRR. However, 5.5 nm-thick NbN films on GaAs still exhibit ΤC=10.7 Κ, ΔΤC=1.1 Κ and RRR=0.7, which compares with 4.5 nm thick films on MgO, making them suitable for device fabrication. To our knowledge, the growth of such high quality thin NbN films on GaAs and DBRs, has never been reported in literature. The degradation of the superconducting properties exhibited by NbN films on GaAs and DBRs was attributed to a highly defected microstructure, due both to a higher lattice misfit between NbN and GaAs and to a poorer quality of the substrate surface. Encouraging preliminary results show that the quality of these films can be improved either cleaning the GaAs/DBR substrate surface more effectively or adding an MgO buffer layer. SSPDs were fabricated on thin NbN films (th=3-7 nm) deposited under optimal conditions on MgO and GaAs by EBL and reactive ion etching. The geometrical parameters of our detectors are: Ad=5×5 µm2, w=60-200 nm, f=40%-60%. The devices were then characterized both electrically and optically. I-V curves of test structures were measured, from which it was possible to deduce important physical parameters used as figures of merit to estimate the superconducting properties of the nanowires, or for the design and the simulation of the devices. The quality of the devices fabricated on GaAs is poorer than those on MgO, most likely due to the lower quality of NbN films deposited on GaAs and to issues related to the EBL nano-patterning step. Measurements of η and of DK as a function of the bias current were performed on SSPDs fabricated on MgO and GaAs. The best performance was exhibited by a w=100 nm, f=40%, th=4 nm meander, showing η=20% and noise equivalent power NEP=10-16 W/Hz1/2 (at λ=1.3 µm and T=4.2 K), which are state of the art values. This result showed for the first time that high performance NbN SSPDs can be realized on a different substrate and from a deposition process at lower temperature than previously reported. High detection efficiencies could not be measured with SSPDs fabricated on GaAs, but it should be noted that at present only first-generation devices (fabricated on GaAs substrates of poor surface quality) have been tested. Better results are expected from devices fabricated on the improved NbN films grown on clean or MgO-buffered GaAs substrates. Although SSPDs on MgO have shown high detection efficiency, the fabrication yield of high performance detectors has to be improved. Variations of the critical current along a nanowire are responsible for the wide distribution in efficiency values of nominally identical SSPDs. In order to understand the physical origin of the nanowire constrictions (i.e. regions of suppressed superconductivity) we performed a spatially-resolved characterization of η of a long straight nanowire, followed by a high resolution SEM (scanning electron microscope) scan on its whole length. Two types of inhomogeneities were evidenced, corresponding to localized efficiency dips and peaks. The peaks likely correspond to constrictions. SEM observations did not evidence any width narrowing at the position of the efficiency peaks, which suggests that constrictions might be due to thickness or quality inhomogeneities of the film occurring during the film deposition or later in the process. On the other hand, the efficiency dips have been correlated with lithography problems discovered on SEM images. Finally, a new photon number resolving detector, the Parallel Nanowire Detector (PND), has been demonstrated, which significantly outperforms existing approaches in terms of sensitivity, speed and multiplication noise in the telecommunication wavelength range. In particular, it provides a repetition rate (80 MHz) three orders of magnitude larger than any existing detector at telecom wavelength, and a sensitivity (NEP=4.2×10-18 W/Hz1/2) one-two orders of magnitude better, with the exception of transition-edge sensors (which require a much lower operating temperature). An electrical equivalent model of the device was developed in order to study its operation. The modeling predicts a physical limit to the reset time of the PND, which is lower than initially estimated. Furthermore, the figures of merit of the device performance in terms of efficiency, speed and sensitivity were defined and their dependency on the design parameters analyzed. Additionally, we developed modeling tools to fully characterize the device and an algorithm to estimate the photon number statistics of an unknown light using the PND. The reconstruction proved to be successful only for low photon fluxes, most likely due to the limited counting capability and the poor calibration of the detector. The PND, with its high repetition rate and high sensitivity, is then suitable for measuring an unknown photon number probability distribution assuming accurate calibration and sufficient counting capability. ______________________________[1] G. N. Gol'tsman, O. Okunev, G. Chulkova, A. Lipatov, A. Semenov, K. Smirnov, B. Voronov, A. Dzardanov, C. Williams, and R. Sobolewski, Appl. Phys. Lett. 79, 705 (2001).
Abstract Superconducting Nanowire Single-Photon Detectors (SNSPDs) are key building blocks for photonic quantum technologies due to their ability to detect single photons with ultra-high efficiency, low dark counts and fast temporal resolution. Superconducting materials exhibiting high uniformity, large absorption cross-section and atomic-scale thickness are desirable to extend single-photon detection from the near-infrared up to the terahertz regime, where existing material choices are especially constrained. Substrate independence would further open the way to integrating detectors onto functional materials and heterostructures, enhancing performance and enabling proximal readout of a wide range of individual excitations. Here, we pattern the prototypical two-dimensional superconductor niobium diselenide (NbSe 2 ) into few-layer nanowires less than 100 nm wide and demonstrate single-photon detection at 780 nm and 1550 nm. At the same time, the dark-count rate remains below 1 Hz up to the switching current and we achieve a timing jitter below 50 ps. We estimate via a diffusive hot-spot model that materials and geometric parameters would allow a theoretical cut-off wavelength in the millimetre range, assuming state-of-the-art device parameters. Our results open up routes toward quantum-limited detectors integrated into quantum-photonic circuits and quantum devices, with the potential for novel detection capabilities and unprecedented energy sensitivity.
Abstract The advancement of superconducting nanowire single-photon detectors (SNSPDs or SSPDs) is intrinsically linked to breakthroughs in superconducting materials engineering. These detectors are prized for their excellent sensitivity and performance across a wide wavelength range, from ultra-violet to mid-infrared (mid-IR). Plasma-enhanced atomic layer deposition (ALD) is an advanced deposition technique that enables exceptional film uniformity across large wafers, making it ideal for a variety of applications. In this study, ALD NbTiN films are fabricated into SNSPDs that exhibit single-photon response across near- to mid-IR wavelengths. A 5 nm thick NbTiN film was patterned into devices consisting of ∼100 nm wide meandered nanowires, and the nanowire cross-section and composition were analysed by transmission electron microscopy. The devices were tested in a closed-cycle cryostat with a base temperature of 0.9 K. Photon detection rate and timing jitter were measured across the wavelength range 1.5–4.4 µ m under low dark count conditions, confirming single-photon sensitivity across the measured wavelength bands. This work introduces the ALD-grown NbTiN films as a new platform for SNSPD detectors, achieving mid-IR single-photon sensitivity. The intact film quality after fabrication demonstrates the potential of ALD processes for scalable infrared detector technologies.