Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Improving Photon Number Resolution in Superconducting Nanowire Single-Photon Detectors with Integrated Impedance Tapers

Bladimiro E. Valbuena, Daniel F. Santavicca

Published Jan 1, 2020• 0 citations
OpenAlex

Abstract

Simulations are run to optimize the ability to resolve the number of photons detected from the pulse height by a Superconducting Nanowire Single-Photon Detector (SNSPD). This is set up in a manner that features an impedance-matching transmission line taper that provides a characteristic impedance which transitions from kΩ to 50 Ω, with the taper providing an effective load impedance that outputs pulses with not only larger amplitudes but also showed a distinct separation for multi-photon events. The first part of this project tries to computationally match the experimental results obtained by our collaborators at MIT. Once these results are achieved, we try to modify the device geometry to improve the key detector metrics which include timing jitter, dark count rate, reset time, and overall detection efficiency.

Related papers

Superconducting nanowire single-photon detector with integrated impedance-matching taper

Di Zhu, Marco Colangelo, Boris A. Korzh +11 more

Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB × Zload, where Zload is limited to 50 Ω in standard r.f. electronics. Here, we break this limit by interfacing the 50 Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. At the expense of reduced maximum counting rate, it increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, we experimentally observed a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter. The results match our numerical simulation, which incorporates both the hotspot dynamics in the SNSPD and the distributed nature in the transmission line taper. The taper studied here may become a useful tool to interface high-impedance superconducting nanowire devices to conventional low-impedance circuits.

arXiv:1811.03991•Applied Physics Letters•Jan 28, 2019•41 citations

Impedance matched superconducting nanowire photodetector for single- and multi-photon detection

Di Zhu

Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB×Zload, where Zload is limited to 50Ω in standard RF electronics. This limit is broken/exceeded by interfacing the 50Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. The taper increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter was observed. The taper also makes the detector's output voltage sensitive to the number of photon-induced hotspots and enables photon number resolution.

•Oct 26, 2023•0 citations

Resolving Photon Numbers Using a Superconducting Nanowire with Impedance-Matching Taper

Di Zhu, Marco Colangelo, Changchen Chen +4 more

Time- and number-resolved photon detection is crucial for quantum information processing. Existing photon-number-resolving (PNR) detectors usually suffer from limited timing and dark-count performance or require complex fabrication and operation. Here, we demonstrate a PNR detector at telecommunication wavelengths based on a single superconducting nanowire with an integrated impedance-matching taper. The taper provides a kΩ load impedance to the nanowire, making the detector's output amplitude sensitive to the number of photon-induced hotspots. The prototyping device was able to resolve up to four absorbed photons with 16.1 ps timing jitter and <2 c.p.s. device dark count rate. Its exceptional distinction between single- and two-photon responses is ideal for high-fidelity coincidence counting and allowed us to directly observe bunching of photon pairs from a single output port of a Hong-Ou-Mandel interferometer. This detector architecture may provide a practical solution to applications that require high timing resolution and few-photon discrimination.

arXiv:1911.09485•Nano Letters•Apr 9, 2020•111 citations

Photon-number resolution with superconducting nanowires

F. B. Baalbergen

Superconducting Nanowire Single Photon Detectors (SNSPDs) are fast and efficient detectors with important applications in optical quantum computers and quantum networks. Current SNSPD implementations lack intrinsic single-wire photon-number resolution. This thesis discusses the electronic and optical characterization of SNSPDs with the goal of obtaining high-speed, high-efficiency photon-number-resolving detectors. Novel laser-induced relaxation oscillations are observed, caused by laser pulses triggering the detector and changing its biasing condition. This leads to discrete steps in the count rate at integer multiples of the pulsed laser repetition rate and limits the maximum achievable count rate for SNSPDs. A Monte Carlo Markov Chain method is applied to detector tomography to characterize single-photon detectors with unprecedented accuracy, and can be applied to detectors regardless of their detection efficiency. Photon number resolution is achieved in (commercial) SNSPDs by projecting measured voltage traces onto the derivative of the average voltage trace. This method enables discrimination of photon numbers by measuring the time difference between traces in a noise-resilient way. The final chapters discuss the design and characterization of impedance-tapered SNSPDs. These devices show both differences in pulse heights and timing depending on the photon number.

•Nov 3, 2026•0 citations

Photon-Number Resolution Using Superconducting Tapered Nanowire Detector

Di Zhu, Marco Colangelo, Changchen Chen +4 more

We show that a superconducting nanowire with an integrated impedance-matching taper can resolve photon numbers. The taper increases the nanowire detector’s output amplitude and makes it sensitive to the number of single-photon-induced hotspots.

Conference on Lasers and Electro-Optics•Jan 1, 2020•0 citations

Impedance-Matched Differential Superconducting Nanowire Detectors

Marco Colangelo, Boris A. Korzh, Jason P. Allmaras +23 more

Superconducting nanowire single-photon detectors (SNSPDs) are the highest-performance photon-counting technology in the near infrared, but traditional designs typically trade off between timing resolution and detection efficiency. The authors utilize transmission-line engineering and differential readout to achieve a design with high detection efficiency and low jitter simultaneously. This design also enables imaging capabilities and photon-number resolution, and is compatible with commercial time taggers. The device is a versatile solution for photon counting in various applications, including quantum computing, quantum communication, biomedicine, and ranging.

arXiv:2108.07962•Physical Review Applied•Apr 28, 2023•45 citations
Simulations are run to optimize the ability to resolve the number of photons detected from the pulse height by a Superconducting Nanowire Single-Photon Detector (SNSPD). This is set up in a manner that features an impedance-matching transmission line taper that provides a characteristic impedance which transitions from kΩ to 50 Ω, with the taper providing an effective load impedance that outputs pulses with not only larger amplitudes but also showed a distinct separation for multi-photon events. The first part of this project tries to computationally match the experimental results obtained by our collaborators at MIT. Once these results are achieved, we try to modify the device geometry to improve the key detector metrics which include timing jitter, dark count rate, reset time, and overall detection efficiency.
Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB × Zload, where Zload is limited to 50 Ω in standard r.f. electronics. Here, we break this limit by interfacing the 50 Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. At the expense of reduced maximum counting rate, it increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, we experimentally observed a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter. The results match our numerical simulation, which incorporates both the hotspot dynamics in the SNSPD and the distributed nature in the transmission line taper. The taper studied here may become a useful tool to interface high-impedance superconducting nanowire devices to conventional low-impedance circuits.
Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB×Zload, where Zload is limited to 50Ω in standard RF electronics. This limit is broken/exceeded by interfacing the 50Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. The taper increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter was observed. The taper also makes the detector's output voltage sensitive to the number of photon-induced hotspots and enables photon number resolution.
Time- and number-resolved photon detection is crucial for quantum information processing. Existing photon-number-resolving (PNR) detectors usually suffer from limited timing and dark-count performance or require complex fabrication and operation. Here, we demonstrate a PNR detector at telecommunication wavelengths based on a single superconducting nanowire with an integrated impedance-matching taper. The taper provides a kΩ load impedance to the nanowire, making the detector's output amplitude sensitive to the number of photon-induced hotspots. The prototyping device was able to resolve up to four absorbed photons with 16.1 ps timing jitter and <2 c.p.s. device dark count rate. Its exceptional distinction between single- and two-photon responses is ideal for high-fidelity coincidence counting and allowed us to directly observe bunching of photon pairs from a single output port of a Hong-Ou-Mandel interferometer. This detector architecture may provide a practical solution to applications that require high timing resolution and few-photon discrimination.
Superconducting Nanowire Single Photon Detectors (SNSPDs) are fast and efficient detectors with important applications in optical quantum computers and quantum networks. Current SNSPD implementations lack intrinsic single-wire photon-number resolution. This thesis discusses the electronic and optical characterization of SNSPDs with the goal of obtaining high-speed, high-efficiency photon-number-resolving detectors. Novel laser-induced relaxation oscillations are observed, caused by laser pulses triggering the detector and changing its biasing condition. This leads to discrete steps in the count rate at integer multiples of the pulsed laser repetition rate and limits the maximum achievable count rate for SNSPDs. A Monte Carlo Markov Chain method is applied to detector tomography to characterize single-photon detectors with unprecedented accuracy, and can be applied to detectors regardless of their detection efficiency. Photon number resolution is achieved in (commercial) SNSPDs by projecting measured voltage traces onto the derivative of the average voltage trace. This method enables discrimination of photon numbers by measuring the time difference between traces in a noise-resilient way. The final chapters discuss the design and characterization of impedance-tapered SNSPDs. These devices show both differences in pulse heights and timing depending on the photon number.
Superconducting nanowire single-photon detectors (SNSPDs) are the highest-performance photon-counting technology in the near infrared, but traditional designs typically trade off between timing resolution and detection efficiency. The authors utilize transmission-line engineering and differential readout to achieve a design with high detection efficiency and low jitter simultaneously. This design also enables imaging capabilities and photon-number resolution, and is compatible with commercial time taggers. The device is a versatile solution for photon counting in various applications, including quantum computing, quantum communication, biomedicine, and ranging.