Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Development of a coaxial circuit QED architecture for quantum computing

Joseph Rahamim

Published Jan 1, 2019• 0 citations
Publisher

Abstract

Superconducting circuit QED is a promising approach for building a quantum computer. In order to realise superconducting circuits at a sufficient scale for useful near-term applications, an architecture with an extensible design is required which implements good connectivity between qubits, and allows for selective readout and control of the qubits without introducing detrimental crosstalk or decoherence. This thesis describes the development of a new coaxial circuit QED architecture that fulfils this requirement of extensibility by incorporating out-of-plane wiring into the sample holder. Single-qubit unit cells consisting of a transmon qubit and readout resonator with coaxial geometries are fabricated on opposing sides of a substrate, and selective control and readout of the qubits is achieved via a capacitance to coaxial wiring built into the device enclosure. Unit cells of qubit and resonator can be arranged in a 2D array without modification of the wiring scheme. A single-qubit unit cell of this architecture is used to implement dispersive circuit QED, and a full characterisation of the Hamiltonian is performed. The device is shown to have parameters comparable to those found in other approaches, such as a coupling between qubit-resonator of ~100 MHz and a coherence time of order ~10 µs. The extension of this scheme to 2D arrays of qubits is then presented, and realizations of two-qubits gates are demonstrated with fidelities all above 87% on a four qubit device. Further evaluations are performed on multi-qubit devices, including a characterisation of the drive isolation of the mode-matched drive ports, finding values in the range of 50 dB and 30 dB for measurement and control respectively. Similarly, the cross coupling between circuits is shown to have values ~2% of the coupling within a unit cell. The effective circuit temperatures are measured, finding typical values of ~100 mK, and the techniques of spin-locking and T2 spectroscopy are employed to probe the noise environment. Finally the architecture is extended to incorporate frequency tuning of qubits with gradiometric SQUID loops by way of off-chip flux bias lines (FBLs). These lines are used to tune qubits with a signal isolation of >99%. Furthermore, the ability of these FBLs to dynamically control the qubit frequency is shown by demonstrating switching of the frequency on a nanosecond time-scale, and parametric driving over a frequency range of gigahertz.

DOI
10.5287/ora-daeyg09rj

Related papers

Double-sided coaxial circuit QED with out-of-plane wiring

Joseph Rahamim, Tanja Behrle, M. J. Peterer +6 more

Superconducting circuits are well established as a strong candidate platform for the development of quantum computing. In order to advance to a practically useful level, architectures are needed which combine arrays of many qubits with selective qubit control and readout, without compromising on coherence. Here, we present a coaxial circuit quantum electrodynamics architecture in which qubit and resonator are fabricated on opposing sides of a single chip, and control and readout wiring are provided by coaxial wiring running perpendicular to the chip plane. We present characterization measurements of a fabricated device in good agreement with simulated parameters and demonstrating energy relaxation and dephasing times of T1 = 4.1 μs and T2 = 5.7 μs, respectively. The architecture allows for scaling to large arrays of selectively controlled and measured qubits with the advantage of all wiring being out of the plane.

arXiv:1703.05828•Applied Physics Letters•May 29, 2017•80 citations

Experiments on multi-level superconducting qubits and coaxial circuit QED

Michael Peterer

Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.

•Jan 1, 2016•1 citation

Multi-mode coaxial transmon qubits for quantum computing and sensing

Wills, James Fox

Superconducting circuits are well established as a viable candidate for the realisation of quantum computers. Circuits based on the transmon qubit are now ubiquitous, owing to its simple design and reduced control wiring overhead. An issue with transmon qubit-based architectures is the always-on unwanted interactions that impose limits on gate speeds and introduce errors into their operation. In addition, understanding sources of noise and decoherence is essential to the low-error operation quantum computers. This thesis describes the implementation of a multi-mode superconducting qubit in a coaxial circuit QED architecture. Constructed from three superconducting islands, connected via two Josephson junctions, the device possesses two transmon-like modes with orthogonal field symmetries. The unique polarisation of each mode allows for engineering dissipation and coupling in the system, extending functionality beyond the single-mode transmon. Experimental results on the unit-cell of the two-mode coaxial transmon are presented, demonstrating coherent control and simultaneous dispersive readout of the modes of the device. A predictive theory of charge sensitivity in a multi-mode superconducting qubit is presented, and experimental results in agreement of this theory are shown, observing sensitivity to four charge-parity configurations and two independent gate-charge offsets. The utility of a multi-mode qubit as a charge detector in spatially tracking local-charge drift of ≃ 100 µm length scales is also shown, demonstrating the use of these devices as tools in understanding charge noise in superconducting circuits. Finally, a system of a pair of coupled two-mode coaxial transmons is introduced, demonstrating a highly mode-selective coupling architecture. A suppressed quantum crosstalk of 2 kHz between protected modes of the devices is measured, along with equal single qubit gate fidelities when operated both individually and simultaneously. A first characterisation of a microwave activated conditional phase interaction between computational modes driven via ancillary transitions (AT-MAP) is presented. Whilst not shown in this work, this state-dependent two-qubit interaction can be used to generate entanglement. Combined with the low crosstalk demonstrated, this shows the multi-mode qubit architecture is a promising candidate for the construction of larger scale quantum processors with fast gates and low crosstalk-related errors.

•Jan 1, 2022•0 citations

Circuit Quantum Electrodynamics with Flux Qubits

Jean-Luc Orgiazzi

This thesis presents circuit quantum electrodynamic (cQED) experiments done with artificial atoms coupled to a high quality factor superconducting microwave resonator. This work discusses the theoretical framework, design, fabrication, implementation and characterization of a multi-qubit system using superconducting persistent current qubits, often referred as flux qubits. \n \nWe developed a new type of cryogenic aid for fast turnaround microwave experiments. The minimum turnaround time to perform microwave experiments in dilution refrigerators is typically a few days, as required by cooling down and warming up the entire refrigerator. The cryogenic microwave payload and wiring needed for each qubit and resonator add a significant heat load to \nthe system which typically only has a few µW s of cooling power at millikelvin temperatures. We present a new experimental approach we developed in which a suitable sample holder is attached to a cold-insertable probe and brought in contact with transmission lines permanently mounted inside the cryostat. The total turnaround time is reduced to 8 hours if the target temperature is 80 mK. This new measurement method increased our ability to successfully identify good devices with fast design-characterization iterations, while allowing months-long measurements at 30 mK. \n \nOur device architecture uses several qubits, each of which is controlled via on-chip fast flux bias lines. Readout of the qubit’s quantum state is performed by homodyne detection of the resonator field at large driving power. We observe long coherence times at the optimal bias point of the flux qubits and present decoherence measurements around this optimal point, where the \nflux qubits couple mostly to magnetic flux noise. Dynamical decoupling techniques employing fast microwave pulses are used to protect the qubit’s coherence and allow calculating the magnetic flux noise power spectral density of the qubit’s environment. Photon-mediated interaction between distant qubits in the resonator allows the implementation of a two-qubit controlled-NOT gate \nusing the selective darkening technique. \n \nThis multi-qubit superconducting design is an interesting platform to study the decoherence properties of flux qubits, the properties of strong interaction of electromagnetic radiation with macroscopic quantum systems. These results demonstrate the potential of cQED as a platform for fundamental investigations of decoherence and quantum dynamics of flux qubits.

•Sep 23, 2019•0 citations

Characterizing superconducting qubits

Sofia Patomäki

In a quantum computer, the information carriers, which are bits in ordinary computers, are implemented as devices that exhibit coherent superpositions of physical states and entanglement. Such components, known as quantum bits or qubits, can be realized with various different types of two-state quantum systems. Quantum computers will be built for computational speed, with hoped for applications especially in cryptography and in other tasks where classical computers remain inefficient. Circuit quantum electrodynamics (cQED) is a quantum-computer architecture which employs superconducting electronic components and microwave photon fields as building blocks. Compared to cavity quantum electrodynamics (CQED), where atoms are trapped in physical cavities, cQED is more attractive in that its qubits are tunable and conveniently integrable with the electronics already in use. This architecture has shown some of the most promising qubit designs, despite their coherence times reaching tens of microseconds, are still below the state of the art with spin qubits, which reach milliseconds. Coherence times are historically the most relevant parameters describing the fitness of a qubit, although these days not necessarily the limiting factor. This thesis presents a comprehensive set of theoretical and experimental methods for measuring the characteristic parameters of superconducting qubits. We especially study transmission-line-shunted plasma oscillation qubits, or transmons, and presents experimental results for a single sample. Transmon capacitively couples a superconducting quantum interference device (SQUID) with a coplanar waveguide (CPW) resonator, often with added frequency tunability utilizing an external magnet. The number of superconducting charge carriers tunnelled through a junction in the SQUID are used as qubit degrees of freedom. Readout of the qubit state is carried out by measuring transmission through the CPW. A cryogenic setup is employed with measurement and driving pulses delivered from microwave sources. Steady-state spectroscopy is employed to determine the resonance frequencies of the qubit and the resonator, qubit-resonator coupling constants, and the energy parameters of the qubit. Pulse-modulated measurements are employed to determine the coherence times of the qubit. The related analysis- and simulation programs and scripts are collected togithub.com/patomaki.

Työväentutkimus Vuosikirja•Jan 1, 2017•0 citations

New avenues in circuit QED: from quantum information to quantum sensing

Boettcher, Charlotte Lang

One of the key elements in circuit quantum electrodynamics (cQED) is the superconducting microwave resonator, which can enable strong coupling to and between nanoscale quantum systems, and as a result has emerged as an essential tool for both quantum information and quantum sensing. In this thesis, I will discuss new applications of superconducting resonators in both of these fields, which illustrates how quantum information and quantum sensing can be strongly tied together. As the field of quantum information continues to grow, various platforms for realizing a quantum computer have been proposed. One attractive platform is to control and manipulate the spin of an electron to form spin qubits, which have demonstrated a long coherence time, weak coupling to the environment, and high fidelity single- and two-qubit gates. However, scaling beyond two qubits has proven challenging, as has incorporating long-range coupling, although both are crucial for making spin qubits a scalable quantum computing platform. The confinement of electromagnetic fields in superconducting resonators enables strong coupling to small systems, such as the single electrons of a spin qubit. In the first part of this thesis, I will describe how a singlet-triplet spin qubit coupled to a high-impedance superconducting resonator constitutes a promising architecture for mediating long-ranged interactions based on a longitudinal coupling between the resonator and qubit. I will discuss the technical developments needed to successfully implement this novel type of interaction in a hybrid spin qubit-resonator device. This type of interaction has several advantages over the more commonly studied transverse coupling scheme: it does not require careful tuning of the qubit frequency to match that of the resonator, which facilitates scaling to a large number of qubits, and also avoids the loss of coherence, which is inevitable in resonant coupling. This type of interaction therefore opens promising paths for generating high-fidelity long-ranged two-qubit coupling by employing superconducting microwave resonators. By adapting techniques used in quantum information, we have also developed a new technique in quantum sensing, where we employ superconducting resonators as a probe of quantum materials such as mesoscopic systems, two-dimensional materials, and heterostructures, which are otherwise challenging to experimentally access with conventional techniques. In the second part of my thesis, I will discuss how implementing cQED techniques from quantum information allows us to probe the symmetry of the order parameter in unconventional superconductors. Unconventional superconductors are not readily available, and we therefore study an engineered system that comprises of interfacing a ferromagnet and superconductor, in which unconventional pairing can be induced into the ferromagnet. This platform allows us to simultaneously excite spin waves, a collective excitation of spins, in the ferromagnet, which opens new directions for studying interactions between coherently coupled magnons (quanta of spin waves) and unconventional superconducting states. Finally, by applying the same technique to a two-dimensional (2D) superconductor, tungsten ditelluride, we leverage this platform in an attempt to study the order parameter of its intrinsic superconducting phase. The nature of the order parameter in this material remains an open question, as both topological and superconducting phases can exist, possibly simultaneously. This work thus demonstrates a unique use of superconducting resonators beyond quantum information applications.

•Jan 1, 2022•0 citations
Superconducting circuit QED is a promising approach for building a quantum computer. In order to realise superconducting circuits at a sufficient scale for useful near-term applications, an architecture with an extensible design is required which implements good connectivity between qubits, and allows for selective readout and control of the qubits without introducing detrimental crosstalk or decoherence. This thesis describes the development of a new coaxial circuit QED architecture that fulfils this requirement of extensibility by incorporating out-of-plane wiring into the sample holder. Single-qubit unit cells consisting of a transmon qubit and readout resonator with coaxial geometries are fabricated on opposing sides of a substrate, and selective control and readout of the qubits is achieved via a capacitance to coaxial wiring built into the device enclosure. Unit cells of qubit and resonator can be arranged in a 2D array without modification of the wiring scheme. A single-qubit unit cell of this architecture is used to implement dispersive circuit QED, and a full characterisation of the Hamiltonian is performed. The device is shown to have parameters comparable to those found in other approaches, such as a coupling between qubit-resonator of ~100 MHz and a coherence time of order ~10 µs. The extension of this scheme to 2D arrays of qubits is then presented, and realizations of two-qubits gates are demonstrated with fidelities all above 87% on a four qubit device. Further evaluations are performed on multi-qubit devices, including a characterisation of the drive isolation of the mode-matched drive ports, finding values in the range of 50 dB and 30 dB for measurement and control respectively. Similarly, the cross coupling between circuits is shown to have values ~2% of the coupling within a unit cell. The effective circuit temperatures are measured, finding typical values of ~100 mK, and the techniques of spin-locking and T2 spectroscopy are employed to probe the noise environment. Finally the architecture is extended to incorporate frequency tuning of qubits with gradiometric SQUID loops by way of off-chip flux bias lines (FBLs). These lines are used to tune qubits with a signal isolation of >99%. Furthermore, the ability of these FBLs to dynamically control the qubit frequency is shown by demonstrating switching of the frequency on a nanosecond time-scale, and parametric driving over a frequency range of gigahertz.
Superconducting circuits are well established as a strong candidate platform for the development of quantum computing. In order to advance to a practically useful level, architectures are needed which combine arrays of many qubits with selective qubit control and readout, without compromising on coherence. Here, we present a coaxial circuit quantum electrodynamics architecture in which qubit and resonator are fabricated on opposing sides of a single chip, and control and readout wiring are provided by coaxial wiring running perpendicular to the chip plane. We present characterization measurements of a fabricated device in good agreement with simulated parameters and demonstrating energy relaxation and dephasing times of T1 = 4.1 μs and T2 = 5.7 μs, respectively. The architecture allows for scaling to large arrays of selectively controlled and measured qubits with the advantage of all wiring being out of the plane.
Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.
Superconducting circuits are well established as a viable candidate for the realisation of quantum computers. Circuits based on the transmon qubit are now ubiquitous, owing to its simple design and reduced control wiring overhead. An issue with transmon qubit-based architectures is the always-on unwanted interactions that impose limits on gate speeds and introduce errors into their operation. In addition, understanding sources of noise and decoherence is essential to the low-error operation quantum computers. This thesis describes the implementation of a multi-mode superconducting qubit in a coaxial circuit QED architecture. Constructed from three superconducting islands, connected via two Josephson junctions, the device possesses two transmon-like modes with orthogonal field symmetries. The unique polarisation of each mode allows for engineering dissipation and coupling in the system, extending functionality beyond the single-mode transmon. Experimental results on the unit-cell of the two-mode coaxial transmon are presented, demonstrating coherent control and simultaneous dispersive readout of the modes of the device. A predictive theory of charge sensitivity in a multi-mode superconducting qubit is presented, and experimental results in agreement of this theory are shown, observing sensitivity to four charge-parity configurations and two independent gate-charge offsets. The utility of a multi-mode qubit as a charge detector in spatially tracking local-charge drift of ≃ 100 µm length scales is also shown, demonstrating the use of these devices as tools in understanding charge noise in superconducting circuits. Finally, a system of a pair of coupled two-mode coaxial transmons is introduced, demonstrating a highly mode-selective coupling architecture. A suppressed quantum crosstalk of 2 kHz between protected modes of the devices is measured, along with equal single qubit gate fidelities when operated both individually and simultaneously. A first characterisation of a microwave activated conditional phase interaction between computational modes driven via ancillary transitions (AT-MAP) is presented. Whilst not shown in this work, this state-dependent two-qubit interaction can be used to generate entanglement. Combined with the low crosstalk demonstrated, this shows the multi-mode qubit architecture is a promising candidate for the construction of larger scale quantum processors with fast gates and low crosstalk-related errors.
This thesis presents circuit quantum electrodynamic (cQED) experiments done with artificial atoms coupled to a high quality factor superconducting microwave resonator. This work discusses the theoretical framework, design, fabrication, implementation and characterization of a multi-qubit system using superconducting persistent current qubits, often referred as flux qubits. \n \nWe developed a new type of cryogenic aid for fast turnaround microwave experiments. The minimum turnaround time to perform microwave experiments in dilution refrigerators is typically a few days, as required by cooling down and warming up the entire refrigerator. The cryogenic microwave payload and wiring needed for each qubit and resonator add a significant heat load to \nthe system which typically only has a few µW s of cooling power at millikelvin temperatures. We present a new experimental approach we developed in which a suitable sample holder is attached to a cold-insertable probe and brought in contact with transmission lines permanently mounted inside the cryostat. The total turnaround time is reduced to 8 hours if the target temperature is 80 mK. This new measurement method increased our ability to successfully identify good devices with fast design-characterization iterations, while allowing months-long measurements at 30 mK. \n \nOur device architecture uses several qubits, each of which is controlled via on-chip fast flux bias lines. Readout of the qubit’s quantum state is performed by homodyne detection of the resonator field at large driving power. We observe long coherence times at the optimal bias point of the flux qubits and present decoherence measurements around this optimal point, where the \nflux qubits couple mostly to magnetic flux noise. Dynamical decoupling techniques employing fast microwave pulses are used to protect the qubit’s coherence and allow calculating the magnetic flux noise power spectral density of the qubit’s environment. Photon-mediated interaction between distant qubits in the resonator allows the implementation of a two-qubit controlled-NOT gate \nusing the selective darkening technique. \n \nThis multi-qubit superconducting design is an interesting platform to study the decoherence properties of flux qubits, the properties of strong interaction of electromagnetic radiation with macroscopic quantum systems. These results demonstrate the potential of cQED as a platform for fundamental investigations of decoherence and quantum dynamics of flux qubits.
In a quantum computer, the information carriers, which are bits in ordinary computers, are implemented as devices that exhibit coherent superpositions of physical states and entanglement. Such components, known as quantum bits or qubits, can be realized with various different types of two-state quantum systems. Quantum computers will be built for computational speed, with hoped for applications especially in cryptography and in other tasks where classical computers remain inefficient. Circuit quantum electrodynamics (cQED) is a quantum-computer architecture which employs superconducting electronic components and microwave photon fields as building blocks. Compared to cavity quantum electrodynamics (CQED), where atoms are trapped in physical cavities, cQED is more attractive in that its qubits are tunable and conveniently integrable with the electronics already in use. This architecture has shown some of the most promising qubit designs, despite their coherence times reaching tens of microseconds, are still below the state of the art with spin qubits, which reach milliseconds. Coherence times are historically the most relevant parameters describing the fitness of a qubit, although these days not necessarily the limiting factor. This thesis presents a comprehensive set of theoretical and experimental methods for measuring the characteristic parameters of superconducting qubits. We especially study transmission-line-shunted plasma oscillation qubits, or transmons, and presents experimental results for a single sample. Transmon capacitively couples a superconducting quantum interference device (SQUID) with a coplanar waveguide (CPW) resonator, often with added frequency tunability utilizing an external magnet. The number of superconducting charge carriers tunnelled through a junction in the SQUID are used as qubit degrees of freedom. Readout of the qubit state is carried out by measuring transmission through the CPW. A cryogenic setup is employed with measurement and driving pulses delivered from microwave sources. Steady-state spectroscopy is employed to determine the resonance frequencies of the qubit and the resonator, qubit-resonator coupling constants, and the energy parameters of the qubit. Pulse-modulated measurements are employed to determine the coherence times of the qubit. The related analysis- and simulation programs and scripts are collected togithub.com/patomaki.
One of the key elements in circuit quantum electrodynamics (cQED) is the superconducting microwave resonator, which can enable strong coupling to and between nanoscale quantum systems, and as a result has emerged as an essential tool for both quantum information and quantum sensing. In this thesis, I will discuss new applications of superconducting resonators in both of these fields, which illustrates how quantum information and quantum sensing can be strongly tied together. As the field of quantum information continues to grow, various platforms for realizing a quantum computer have been proposed. One attractive platform is to control and manipulate the spin of an electron to form spin qubits, which have demonstrated a long coherence time, weak coupling to the environment, and high fidelity single- and two-qubit gates. However, scaling beyond two qubits has proven challenging, as has incorporating long-range coupling, although both are crucial for making spin qubits a scalable quantum computing platform. The confinement of electromagnetic fields in superconducting resonators enables strong coupling to small systems, such as the single electrons of a spin qubit. In the first part of this thesis, I will describe how a singlet-triplet spin qubit coupled to a high-impedance superconducting resonator constitutes a promising architecture for mediating long-ranged interactions based on a longitudinal coupling between the resonator and qubit. I will discuss the technical developments needed to successfully implement this novel type of interaction in a hybrid spin qubit-resonator device. This type of interaction has several advantages over the more commonly studied transverse coupling scheme: it does not require careful tuning of the qubit frequency to match that of the resonator, which facilitates scaling to a large number of qubits, and also avoids the loss of coherence, which is inevitable in resonant coupling. This type of interaction therefore opens promising paths for generating high-fidelity long-ranged two-qubit coupling by employing superconducting microwave resonators. By adapting techniques used in quantum information, we have also developed a new technique in quantum sensing, where we employ superconducting resonators as a probe of quantum materials such as mesoscopic systems, two-dimensional materials, and heterostructures, which are otherwise challenging to experimentally access with conventional techniques. In the second part of my thesis, I will discuss how implementing cQED techniques from quantum information allows us to probe the symmetry of the order parameter in unconventional superconductors. Unconventional superconductors are not readily available, and we therefore study an engineered system that comprises of interfacing a ferromagnet and superconductor, in which unconventional pairing can be induced into the ferromagnet. This platform allows us to simultaneously excite spin waves, a collective excitation of spins, in the ferromagnet, which opens new directions for studying interactions between coherently coupled magnons (quanta of spin waves) and unconventional superconducting states. Finally, by applying the same technique to a two-dimensional (2D) superconductor, tungsten ditelluride, we leverage this platform in an attempt to study the order parameter of its intrinsic superconducting phase. The nature of the order parameter in this material remains an open question, as both topological and superconducting phases can exist, possibly simultaneously. This work thus demonstrates a unique use of superconducting resonators beyond quantum information applications.