Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.
Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.
Superconducting circuit QED is a promising approach for building a quantum computer. In order to realise superconducting circuits at a sufficient scale for useful near-term applications, an architecture with an extensible design is required which implements good connectivity between qubits, and allows for selective readout and control of the qubits without introducing detrimental crosstalk or decoherence. This thesis describes the development of a new coaxial circuit QED architecture that fulfils this requirement of extensibility by incorporating out-of-plane wiring into the sample holder. Single-qubit unit cells consisting of a transmon qubit and readout resonator with coaxial geometries are fabricated on opposing sides of a substrate, and selective control and readout of the qubits is achieved via a capacitance to coaxial wiring built into the device enclosure. Unit cells of qubit and resonator can be arranged in a 2D array without modification of the wiring scheme. A single-qubit unit cell of this architecture is used to implement dispersive circuit QED, and a full characterisation of the Hamiltonian is performed. The device is shown to have parameters comparable to those found in other approaches, such as a coupling between qubit-resonator of ~100 MHz and a coherence time of order ~10 µs. The extension of this scheme to 2D arrays of qubits is then presented, and realizations of two-qubits gates are demonstrated with fidelities all above 87% on a four qubit device. Further evaluations are performed on multi-qubit devices, including a characterisation of the drive isolation of the mode-matched drive ports, finding values in the range of 50 dB and 30 dB for measurement and control respectively. Similarly, the cross coupling between circuits is shown to have values ~2% of the coupling within a unit cell. The effective circuit temperatures are measured, finding typical values of ~100 mK, and the techniques of spin-locking and T2 spectroscopy are employed to probe the noise environment. Finally the architecture is extended to incorporate frequency tuning of qubits with gradiometric SQUID loops by way of off-chip flux bias lines (FBLs). These lines are used to tune qubits with a signal isolation of >99%. Furthermore, the ability of these FBLs to dynamically control the qubit frequency is shown by demonstrating switching of the frequency on a nanosecond time-scale, and parametric driving over a frequency range of gigahertz.
Abstract Superconducting quantum circuits are a leading platform for quantum-information processing, but their development requires expertise spanning device design, microfabrication, cryogenic operation, microwave control, and quantum characterization. In this work, we report the realization of a flux-tunable superconducting transmon platform and present an integrated workflow encompassing design, fabrication, measurement, and numerical modeling. The device consists of an Al/AlOx/Al transmon coupled to a three-dimensional microwave cavity operating in the circuit quantum electrodynamics (cQED) dispersive regime. Two-tone spectroscopy reveals a fundamental transition frequency of ω01=5.0122GHz and an anharmonicity of α/2π=−202.4MHz , corresponding to EJ/EC≈82.9 . Flux spectroscopy yields a cavity-qubit coupling strength of g/2π=260MHz , while the cavity linewidth gives a loaded quality factor of QL=6127 and a Purcell limit of T1Purcell≈82μs . Time-domain measurements yield coherence times of T1=17.4μs and T2∗=5.8μs . To investigate coherence and dissipation in the device, the experimental observations are analyzed within a Lindblad master-equation framework describing cavity photon loss and thermal excitation, qubit energy relaxation, and pure dephasing processes. Using a set of experimentally extracted parameters, the model reproduces the measured spectroscopic and time-domain observables, providing a quantitative description of the open-system dynamics of the transmon-cavity platform. The analysis shows that the measured coherence is primarily limited by pure dephasing and energy-relaxation processes, whereas thermal excitation plays a minor role under the experimental conditions. Inspired by the broader framework of quantum dissipation in macroscopic quantum systems pioneered by Caldeira and collaborators, this approach enables a quantitative analysis of relaxation and dephasing processes in superconducting quantum circuits. Beyond the characterization of a single device, the present work demonstrates the establishment of the expertise, infrastructure, and experimental workflow required for the design, fabrication, measurement, and modeling of superconducting quantum circuits, contributing to the development of quantum technologies in Brazil and related applications.
Superconducting circuits are well established as a viable candidate for the realisation of quantum computers. Circuits based on the transmon qubit are now ubiquitous, owing to its simple design and reduced control wiring overhead. An issue with transmon qubit-based architectures is the always-on unwanted interactions that impose limits on gate speeds and introduce errors into their operation. In addition, understanding sources of noise and decoherence is essential to the low-error operation quantum computers. This thesis describes the implementation of a multi-mode superconducting qubit in a coaxial circuit QED architecture. Constructed from three superconducting islands, connected via two Josephson junctions, the device possesses two transmon-like modes with orthogonal field symmetries. The unique polarisation of each mode allows for engineering dissipation and coupling in the system, extending functionality beyond the single-mode transmon. Experimental results on the unit-cell of the two-mode coaxial transmon are presented, demonstrating coherent control and simultaneous dispersive readout of the modes of the device. A predictive theory of charge sensitivity in a multi-mode superconducting qubit is presented, and experimental results in agreement of this theory are shown, observing sensitivity to four charge-parity configurations and two independent gate-charge offsets. The utility of a multi-mode qubit as a charge detector in spatially tracking local-charge drift of ≃ 100 µm length scales is also shown, demonstrating the use of these devices as tools in understanding charge noise in superconducting circuits. Finally, a system of a pair of coupled two-mode coaxial transmons is introduced, demonstrating a highly mode-selective coupling architecture. A suppressed quantum crosstalk of 2 kHz between protected modes of the devices is measured, along with equal single qubit gate fidelities when operated both individually and simultaneously. A first characterisation of a microwave activated conditional phase interaction between computational modes driven via ancillary transitions (AT-MAP) is presented. Whilst not shown in this work, this state-dependent two-qubit interaction can be used to generate entanglement. Combined with the low crosstalk demonstrated, this shows the multi-mode qubit architecture is a promising candidate for the construction of larger scale quantum processors with fast gates and low crosstalk-related errors.
In this thesis, experimentally relevant aspects and open questions of quantum information processing and measurement in circuit quantum electrodynamics have been investigated theoretically. Circuit quantum electrodynamics is a relatively young field combining superconducting transmission line resonators on-chip with superconducting quantum bits which serve as artificial atoms. Remarkable experiments have underlined the prospects of circuit QED as a possible architecture for quantum information processing as well as a framework within which quantum optics experiments can be performed. In contrast to their optical counterparts, these experiments reach the ultra-strong coupling limit and allow e.g. the generation of Fock states, the study of decoherence and the observation of quantum jumps. We present the physics of superconducting circuits based on the Josephson junction as a non-linear circuit element. We discuss the various types of quantum bits (qubits) before turning to an introduction on cavity QED and conclude the introduction with a brief presentation of the most relevant experiments and a short introduction to the principles and prospects of quantum information processing. Building on the pioneering theoretical and experimental work in which up to three qubits have been integrated on a chip and successfully coupled via a cavity mode, we propose a scheme to overcome the natural limits concerning scalability in these systems. Usually, scalability is severely limited by the resonance width of the qubit transitions and the attainable frequency range for both qubit transition and cavity resonance frequencies. This limits the present setups to at most ten qubits. As a possible solution, we propose and investigate a cross-bar grid layout of cavities with qubits at the intersections. It turns out that this setup, allowing for up to about 1000 qubits, offers significant advantages over e.g. nearest-neighbor coupling schemes. In addition, it can serve as a building block for a truly scalable scheme for fault-tolerant quantum information processing with superconducting circuits by combining 7x7 arrays in a staircase manner. Furthermore, we discuss and simulate different possibilities to improve upon the suggested scheme by e.g. using resonant gates and optimal control theory. Another focus of the present thesis is measurement physics. In order to investigate e.g. the possibilities of using a circuit QED system to dispersively detect single microwave photons or to generate multi-qubit entangled states, we introduce in a pedagogical manner the basics of stochastic master equations which generate quantum trajectories before turning to concrete applications. Quantum trajectories have proven to be a state-of-the-art tool to analyze measurement situations in a very realistic manner by giving access to both the measurement record as well as the internal quantum dynamics conditioned on this record. Using the method of quantum trajectories as generated by stochastic master equations, we discuss a scheme to efficiently generate multi-qubit entangled states in a very flexible way. The method is based on a collective, dispersive qubit readout. By this measurement, a suitable product state of N qubits can be reliably converted into e.g. an N-qubit Greenberger-Horne-Zeilinger or W state. We propose and discuss the scheme and investigate the effects of decoherence and parameter spread as they would be encountered in experiment. Last but not least, we propose and fully analyze a scheme to dispersively detect single itinerant microwave photons. While experiments to generate single microwave photons have already been successfully performed, their single-shot quantum non-demolition detection has not been possible so far. The scheme presented in this thesis closes this gap in the circuit QED toolbox and reaches detection efficiencies of 30% only limited by fundamental quantum mechanics in this case the Quantum Zeno effect. This detection scheme could be used in quantum communication or quantum cryptography applications.
Superconducting circuits are well established as a strong candidate platform for the development of quantum computing. In order to advance to a practically useful level, architectures are needed which combine arrays of many qubits with selective qubit control and readout, without compromising on coherence. Here, we present a coaxial circuit quantum electrodynamics architecture in which qubit and resonator are fabricated on opposing sides of a single chip, and control and readout wiring are provided by coaxial wiring running perpendicular to the chip plane. We present characterization measurements of a fabricated device in good agreement with simulated parameters and demonstrating energy relaxation and dephasing times of T1 = 4.1 μs and T2 = 5.7 μs, respectively. The architecture allows for scaling to large arrays of selectively controlled and measured qubits with the advantage of all wiring being out of the plane.
Quantum information processing holds the promise of a paradigm shift in computational power for specific problem classes. While contemporary quantum processors operate in the Noisy Intermediate-Scale Quantum (NISQ) regime and remain highly susceptible to errors, ongoing experimental efforts on these near-term devices are crucial for advancing the underlying technology. Among the various hardware implementations, superconducting quantum circuits stand out as one of the most robust architectures for scalable quantum technologies. Nevertheless, the primary bottleneck in these systems is the fragility of quantum information: interactions with the environment inevitably perturb the quantum states, a phenomenon known as decoherence. This rapid loss of stored information imposes a fundamental limit on the time available to reliably execute computations on these devices. Within this context, this thesis focuses on the comprehensive experimental characterization of a planar chip featuring isolated, fixed-frequency superconducting transmon qubits. The measurements were conducted in a cryogenic environment, relying on a dilution refrigerator to maintain the device at millikelvin temperatures. To probe the quantum system under these conditions, custom measurement scripts were developed to operate state-of-the-art microwave control electronics (Keysight Quantum Control System), establishing full control over pulse generation, signal acquisition, and digital demodulation. The experimental workflow systematically mapped the physical properties of the device through a progressive series of characterization steps. Initial spectroscopic techniques probed the coupled resonator-qubit system, identifying its fundamental transition frequencies and relevant energy scales. Building upon these frequency-domain measurements, coherent control was achieved by calibrating resonant microwave pulses to drive single-qubit rotations, enabling the reliable preparation of the qubit in excited or coherent superposition states. Finally, specific time-domain protocols were implemented to evaluate the operational limits of the device. By executing standard pulse sequences, the characteristic decoherence metrics of the system, namely the longitudinal energy relaxation time (T1) and the inhomogeneous dephasing time (T2*), were successfully extracted, providing a quantitative assessment of the qubit's overall performance and establishing a baseline for future implementations of more advanced quantum control protocols.