Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

ACS Applied Materials & Interfaces

Controlled Doping of GeV and SnV Color Centers in Diamond Using Chemical Vapor Deposition

Mika T. Westerhausen, Aleksandra Trycz, Connor Stewart, Milad Nonahal, Blake Regan, Mehran Kianinia, Igor Aharonovich

Published Jun 3, 2020• 24 citations
Publisher

Abstract

Group IV color centers in diamond (Si, Ge, Sn, and Pb) have recently emerged as promising candidates for realization of scalable quantum photonics. However, their synthesis in nanoscale diamond is still in its infancy. In this work we demonstrate controlled synthesis of selected group IV defects (Ge and Sn) into nanodiamonds and nanoscale single crystal diamond membranes by microwave plasma chemical vapor deposition. We take advantage of inorganic salts to prepare the chemical precursors that contain the required ions that are then incorporated into the growing diamond. Photoluminescence measurements confirm that the selected group IV emitters are present in the diamond without degrading its structural quality. Our results are important to expand the versatile synthesis of color centers in diamond.

DOI
10.1021/acsami.0c07242

Related papers

Fabrication and Photoluminescence Studies of Tin-Vacancy Centers in Chemical Vapor Deposition Diamond

Rani Mary Joy, Miquel Cherta Garrido, Omar J. Y. Harb +8 more

Group IV color centers in diamond are promising single-photon emitters for quantum information processing and networking. Among them, the tin-vacancy (SnV) center stands out due to its long spin coherence times at cryogenic temperatures above 1 K. While SnV centers have been realized using various fabrication routes, their in situ formation via microwave plasma-enhanced chemical vapor deposition (MW PE CVD) remains relatively unexplored. In this study, SnV centers, identified by a zero-phonon line (ZPL) near 620 nm, were synthesized in nanocrystalline diamond and free-standing microcrystalline diamond using tin oxide (SnO 2 ) as a dopant source at substrate temperatures of 750°C and 850°C. Photoluminescence measurements reveal that lowering the substrate temperature enhances both the ZPL intensity and spatial uniformity of SnV centers. These results highlight substrate temperature as a key parameter for controlling SnV incorporation during MW PE CVD growth and provide insights into optimizing fabrication strategies for diamond-based quantum technologies.

ACS Materials Letters•Dec 2, 2025•1 citation

Generation of Tin-Vacancy Centers in Diamond via Shallow Ion Implantation and Subsequent Diamond Overgrowth

Alison E. Rugar, Haiyu Lu, Constantin Dory +5 more

Group IV color centers in diamond have garnered great interest for their potential as optically active solid-state spin qubits. The future utilization of such emitters requires the development of precise site-controlled emitter generation techniques that are compatible with high-quality nanophotonic devices. This task is more challenging for color centers with large group IV impurity atoms, which are otherwise promising because of their predicted long spin coherence times without a dilution refrigerator. For example, when applied to the negatively charged tin-vacancy (SnV – ) center, conventional site-controlled color center generation methods either damage the diamond surface or yield bulk spectra with unexplained features. Here we demonstrate a novel method to generate site-controlled SnV – centers with clean bulk spectra. We shallowly implant Sn ions through a thin implantation mask and subsequently grow a layer of diamond via chemical vapor deposition. This method can be extended to other color centers and integrated with quantum nanophotonic device fabrication.

arXiv:1910.14165•Nano Letters•Feb 7, 2020•71 citations

Bottom up engineering of single crystal diamond membranes with germanium vacancy color centers

Aleksandra Trycz, Blake Regan, Mehran Kianinia +3 more

© 2019 Optical Society of America under the terms of the OSA Open Access Publishing Agreement. Color centers in diamond have garnered significant attention for applications in integrated quantum photonics. The availability of thin (~ hundred of nanometers) diamond membranes is paramount to achieve this goal. In this paper, we describe in detail a robust, reproducible and cost effective fabrication method that enables engineering high quality thin diamond membranes with uniform distribution of germanium vacancies employing microwave plasma chemical vapor deposition. We use a combination of different germanium precursors for homogeneous doping of the membranes to increase the probability of germanium incorporation into the diamond lattice. Our fabrication methodology can be further extended to implementation of other color centers in thin diamond membranes and be used for engineering quantum photonic devices.

Optical Materials Express•Nov 20, 2019•14 citations

Photoactivation of group-IV color centers in ion-implanted diamond using continuous-wave laser irradiation

E. Nieto Hernández, Vanna Pugliese, Emilio Corte +2 more

Group-IV color centers in diamond are promising solid-state quantum emitters due to their favorable optical properties, yet deterministic fabrication via ion implantation remains challenging. We investigated the photoactivation of Si-, Ge-, Sn-, and Pb-implanted diamond using continuous-wave (CW) 405 nm laser irradiation at milliwatt powers. The photoactivation follows a characteristic energy dependence consistent with charge state transitions induced by photon absorption. Notably, the PbV − center demonstrated a photoactivation yield of approximately 0.4%, suggesting a viable route for spatially controlled fabrication of single quantum emitters.

Diamond and Related Materials•Aug 4, 2026•0 citations

Germanium-Vacancy Single Color Centers in Diamond

Takayuki Iwasaki, Fumitaka Ishibashi, Yoshiyuki Miyamoto +13 more

Atomic-sized fluorescent defects in diamond are widely recognized as a promising solid state platform for quantum cryptography and quantum information processing. For these applications, single photon sources with a high intensity and reproducible fabrication methods are required. In this study, we report a novel color center in diamond, composed of a germanium (Ge) and a vacancy (V) and named the GeV center, which has a sharp and strong photoluminescence band with a zero-phonon line at 602 nm at room temperature. We demonstrate this new color center works as a single photon source. Both ion implantation and chemical vapor deposition techniques enabled fabrication of GeV centers in diamond. A first-principles calculation revealed the atomic crystal structure and energy levels of the GeV center.

arXiv:1503.04938•Scientific Reports•Aug 7, 2015•369 citations

Fabrication of Tin vacancy centers in nanodiamonds

Hideaki Takashima, Konosuke Shimazaki, Abe Hiroshi +2 more

Nanodiamonds with color centers have recently become a focus of photonic quantum information technologies. Among the various vacancies in diamonds, Tin vacancy (SnV) centers have promising properties[3], such as high brightness, high emission efficiency (60%) from a zero-phonon line (ZPL) at about 620 nm, lifetime-limited linewidths, and a long coherence time of the electronic spin. A reported method for fabricating nanodiamonds, including SnV centers, is the synthesis by microwave plasma chemical vapor deposition[4]. In this method, inorganic compounds were used to introduce a layer of oxides and chlorides that serve Sn ions. However, this method would be difficult to precisely control both the size of the nanodiamonds and the number of defect centers. Here, we report an alternative approach for creating SnV centers in nanodiamonds using ion implantation. We use type-Ib diamond monocrystalline suspension (MSY 0.05, purchased from Microdiamant). Small amounts of the suspension are spin-coated several times on substrates. Sn ions are implanted into the samples with an energy of 800 KeV and ion fluence of 1014 ions/cm2. We then anneal the implanted samples in a high vacuum for about 20 hours at 1200oC. After annealing, the samples are heated at about 500 degrees to remove the sp2 carbon layer on the surface. Finally, the nanodiamonds are transferred to silica substrates. We use a confocal microscope system for the optical measurement. A continuous-wave laser (λ=520 nm) is used to excite the SnV centers in the nanodiamonds. The laser's excitation power is about 10 mW. The laser beam is focused on the nanodiamonds with an objective lens with a numerical aperture of 0.95. The samples are scanned at a step size of 200 nm using a three-axis piezo actuator. The fluorescence is collected with the same objective lens and measured by a single-photon counting module and a spectrometer.

•Nov 19, 2024•0 citations
Group IV color centers in diamond (Si, Ge, Sn, and Pb) have recently emerged as promising candidates for realization of scalable quantum photonics. However, their synthesis in nanoscale diamond is still in its infancy. In this work we demonstrate controlled synthesis of selected group IV defects (Ge and Sn) into nanodiamonds and nanoscale single crystal diamond membranes by microwave plasma chemical vapor deposition. We take advantage of inorganic salts to prepare the chemical precursors that contain the required ions that are then incorporated into the growing diamond. Photoluminescence measurements confirm that the selected group IV emitters are present in the diamond without degrading its structural quality. Our results are important to expand the versatile synthesis of color centers in diamond.
Group IV color centers in diamond are promising single-photon emitters for quantum information processing and networking. Among them, the tin-vacancy (SnV) center stands out due to its long spin coherence times at cryogenic temperatures above 1 K. While SnV centers have been realized using various fabrication routes, their in situ formation via microwave plasma-enhanced chemical vapor deposition (MW PE CVD) remains relatively unexplored. In this study, SnV centers, identified by a zero-phonon line (ZPL) near 620 nm, were synthesized in nanocrystalline diamond and free-standing microcrystalline diamond using tin oxide (SnO 2 ) as a dopant source at substrate temperatures of 750°C and 850°C. Photoluminescence measurements reveal that lowering the substrate temperature enhances both the ZPL intensity and spatial uniformity of SnV centers. These results highlight substrate temperature as a key parameter for controlling SnV incorporation during MW PE CVD growth and provide insights into optimizing fabrication strategies for diamond-based quantum technologies.
Group IV color centers in diamond have garnered great interest for their potential as optically active solid-state spin qubits. The future utilization of such emitters requires the development of precise site-controlled emitter generation techniques that are compatible with high-quality nanophotonic devices. This task is more challenging for color centers with large group IV impurity atoms, which are otherwise promising because of their predicted long spin coherence times without a dilution refrigerator. For example, when applied to the negatively charged tin-vacancy (SnV – ) center, conventional site-controlled color center generation methods either damage the diamond surface or yield bulk spectra with unexplained features. Here we demonstrate a novel method to generate site-controlled SnV – centers with clean bulk spectra. We shallowly implant Sn ions through a thin implantation mask and subsequently grow a layer of diamond via chemical vapor deposition. This method can be extended to other color centers and integrated with quantum nanophotonic device fabrication.
© 2019 Optical Society of America under the terms of the OSA Open Access Publishing Agreement. Color centers in diamond have garnered significant attention for applications in integrated quantum photonics. The availability of thin (~ hundred of nanometers) diamond membranes is paramount to achieve this goal. In this paper, we describe in detail a robust, reproducible and cost effective fabrication method that enables engineering high quality thin diamond membranes with uniform distribution of germanium vacancies employing microwave plasma chemical vapor deposition. We use a combination of different germanium precursors for homogeneous doping of the membranes to increase the probability of germanium incorporation into the diamond lattice. Our fabrication methodology can be further extended to implementation of other color centers in thin diamond membranes and be used for engineering quantum photonic devices.
Group-IV color centers in diamond are promising solid-state quantum emitters due to their favorable optical properties, yet deterministic fabrication via ion implantation remains challenging. We investigated the photoactivation of Si-, Ge-, Sn-, and Pb-implanted diamond using continuous-wave (CW) 405 nm laser irradiation at milliwatt powers. The photoactivation follows a characteristic energy dependence consistent with charge state transitions induced by photon absorption. Notably, the PbV − center demonstrated a photoactivation yield of approximately 0.4%, suggesting a viable route for spatially controlled fabrication of single quantum emitters.
Atomic-sized fluorescent defects in diamond are widely recognized as a promising solid state platform for quantum cryptography and quantum information processing. For these applications, single photon sources with a high intensity and reproducible fabrication methods are required. In this study, we report a novel color center in diamond, composed of a germanium (Ge) and a vacancy (V) and named the GeV center, which has a sharp and strong photoluminescence band with a zero-phonon line at 602 nm at room temperature. We demonstrate this new color center works as a single photon source. Both ion implantation and chemical vapor deposition techniques enabled fabrication of GeV centers in diamond. A first-principles calculation revealed the atomic crystal structure and energy levels of the GeV center.
Nanodiamonds with color centers have recently become a focus of photonic quantum information technologies. Among the various vacancies in diamonds, Tin vacancy (SnV) centers have promising properties[3], such as high brightness, high emission efficiency (60%) from a zero-phonon line (ZPL) at about 620 nm, lifetime-limited linewidths, and a long coherence time of the electronic spin. A reported method for fabricating nanodiamonds, including SnV centers, is the synthesis by microwave plasma chemical vapor deposition[4]. In this method, inorganic compounds were used to introduce a layer of oxides and chlorides that serve Sn ions. However, this method would be difficult to precisely control both the size of the nanodiamonds and the number of defect centers. Here, we report an alternative approach for creating SnV centers in nanodiamonds using ion implantation. We use type-Ib diamond monocrystalline suspension (MSY 0.05, purchased from Microdiamant). Small amounts of the suspension are spin-coated several times on substrates. Sn ions are implanted into the samples with an energy of 800 KeV and ion fluence of 1014 ions/cm2. We then anneal the implanted samples in a high vacuum for about 20 hours at 1200oC. After annealing, the samples are heated at about 500 degrees to remove the sp2 carbon layer on the surface. Finally, the nanodiamonds are transferred to silica substrates. We use a confocal microscope system for the optical measurement. A continuous-wave laser (λ=520 nm) is used to excite the SnV centers in the nanodiamonds. The laser's excitation power is about 10 mW. The laser beam is focused on the nanodiamonds with an objective lens with a numerical aperture of 0.95. The samples are scanned at a step size of 200 nm using a three-axis piezo actuator. The fluorescence is collected with the same objective lens and measured by a single-photon counting module and a spectrometer.