Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Conference on ASIC (ASICON)

An ASIC for Discriminating Single Photon Detector Signal of High-Speed Quantum Key Distribution System

Yulong Zhu, Futian Liang, Xinzhe Wang, Bo Feng, Chenxi Zhu, Ge Jin

Published Oct 1, 2019• 0 citations
Publisher

Abstract

An ASIC is presented in this paper for discriminating signal from single photon detector (SPD) of high-speed quantum key distribution (QKD) system. The circuit is designed in 130 nm CMOS process. It receives and discriminates a small voltage pulse from a SPD, coinciding with a trigger signal and outputs the effective signal to next stage of QKD system. The pulse width of the voltage signal from SPD is less than 400 ps. The circuit mainly consists of bandgap reference, high speed comparator, delay chain and current mode logic (CML) driver. It should operate at a speed of 1.25 GHz. This work integrate all the front-end electronics for SPD into a chip. The area, stray capacitance and power consumption of the whole circuit are reduced. And then the whole receiver of QKD system can be integrated into a chip to improve performance.

DOI
10.1109/asicon47005.2019.8983450

Related papers

Single Photon Source Driver Designed in ASIC

Feng, Bo, Futian Liang, Xinzhe Wang +3 more

The single photon source is an important part of the quantum key distribution (QKD) system. At present, the single photon source is large in size and complex in structure for a lot of discrete components which are used. The miniaturization of the photon source is the tendency of the QKD system. We integrate all laser driver electronic module into one single ASIC chip, which can be used to drive the 1550nm DFB laser in random pulse mode and it can greatly reduce the volume of the single photon source. We present the design of the chip named LSD2018 and simulation results before the tape-out. The LSD2018 is fabricated with a 130 nm CMOS process and consists of a discriminator, an adjustable pulse generator, a bandgap reference, an SPI bus, and an amplitude-adjustable current pulse driver. The electronic random pulse from the driver can go 20mA to 120mA in amplitude and 400ps to 4ns in pulse width. The parameters can be set by an SPI bus.

arXiv:1806.03071•Jun 8, 2018•0 citations

A high-performance integrated single-photon detector for telecom wavelengths

Donald S. Bethune, W. P. Risk, Gary W. Pabst

A commercial avalanche photodiode (APD) and the circuitry needed to operate it as a single-photon detector (SPD) have been integrated onto a single PC board (PCB). At temperatures accessible with Peltier coolers (∼200–240 K), the PCB-SPD achieves high detection efficiency (DE) at 1308 and 1545 nm with low dark-count probability (e.g. ∼10−6/bias pulse at DE = 20%, 220 K), making it useful for quantum key distribution (QKD). The board generates fast bias pulses, cancels noise transients, amplifies the signals, and sends them to an on-board discriminator. A digital blanking circuit suppresses afterpulsing.

arXiv:quant-ph/0311112•Journal of Modern Optics•Jan 1, 2004•71 citations

Jitter suppression scheme for detection pulses in high-speed sinusoidal gated single-photon detectors

Lianjun Jiang, Dongdong Li, Dawei Li +11 more

Abstract Quantum key distribution (QKD) achieves information-theoretic security based on quantum mechanics principles, where single-photon detectors (SPDs) serve as critical components. This study focuses on the sinusoidal gated SPDs widely used in high-speed QKD systems. We investigate the mechanisms underlying the rising-edge jitter in detection signals, identifying contributions from factors such as the temporal width of injected optical pulses, avalanche generation processes, avalanche signal extraction, and pulse discrimination. To address the issue of excessive jitter-induced bit errors, we propose a retiming scheme that utilizes coincidence signals synchronized with the sinusoidal gating signal. This approach effectively suppresses detection signal jitter and reduces the after-pulse probability of the detector. Experimental validation using a high-precision time-to-digital converter (TDC) demonstrates a significant reduction in the rising-edge jitter distribution after applying the suppression scheme. The proposed method features clear principles and straightforward engineering implementation, avoiding direct interference with the detector’s operational processes. The designed high-speed sinusoidal gated InGaAs/InP SPD operates at 1.25 GHz, achieving a remarkable reduction in after-pulse probability from 10.7% (without jitter suppression) to 0.72%, thereby enhancing the overall performance of QKD systems.

Journal of Semiconductors•Dec 1, 2025•1 citation

Photonic integrated quantum key distribution receiver for multiple users

Lingwen Kong, Zhihao Li, Congxiu Li +6 more

Integrated photonics has the advantages of miniaturization, low cost, and CMOS compatibility, and it provides a stable, highly integrated, and practical platform for quantum key distribution (QKD). While photonic integration of optical components has greatly reduced the overall cost of QKD systems, single-photon detectors (SPDs) have become the most expensive part of a practical QKD system. In order to circumvent this obstacle and make full use of SPDs, we have designed and fabricated a QKD receiver chip for multiple users. Our chip is based on a time-division multiplexing technique and makes use of a single set of SPDs to support up to four users' QKD. Our proof-of-principle chip-based QKD system is capable of producing an average secret key rate of 13.68 kbps for four users with a quantum bit error rate (QBER) as low as 0.51% over a simulated distance of 20 km in fiber. Our result clearly demonstrates the feasibility of multiplexing SPDs for setting QKD channels with different users using photonic integrated chip and may find applications in the commercialization of quantum communication technology.

arXiv:2007.03427•Optics Express•May 30, 2020•20 citations

The single-photon detection and data acquisition for the quantum key distribution system

Xiuliang Chen, Chunyuan Zhou, Guang Wu +2 more

In our experiment, two InGaAs/InP avalanche photodiodes (APD) were used in the quantum key distribution (QKD) system for single-photon detection at telecom communication wavelength (1310/1550 nm). By using properly designed passive-quenching circuit, the photo-detection efficiency of the APD could reach 10% at 1550 nm. In order to decrease the dark count rate efficiently, we designed a coincident counting circuits for single-photon detection. Before the APD signals were sent to the signal processing circuit, the avalanche signals were amplified and shaped into the TTL pulses. In order to obtain an accurate and efficient data acquisition and to transfer synchronically several signals such as the TTL signals and pulses from Random generators, we designed a signal processing circuit with the parallel port whose speed limitation is about 100Kb/s. In our experiments of single-photon interference and quantum cryptography, the electronic designs presented us satisfactory performance and results. To achieve much higher speed for the data acquisition, we also employed the Universal Serial Bus System (USB2.0) to interface our single-photon avalanche detectors and random generators used in our QKD system, which was believed to improve the performance of QKD such as the key distribution speed.

Frontiers in Optics•Jan 1, 2003•0 citations

Chip-Based Electronic System for Quantum Key Distribution

Siyuan Zhang, Wei Mao, Shaobo Luo +1 more

Quantum Key Distribution (QKD) has garnered significant attention due to its unconditional security based on the fundamental principles of quantum mechanics. While QKD has been demonstrated by various groups and commercial QKD products are available, the development of a fully chip-based QKD system, aimed at reducing costs, size, and power consumption, remains a significant technological challenge. Most researchers focus on the optical aspects, leaving the integration of the electronic components largely unexplored. In this paper, we present the design of a fully integrated electrical control chip for QKD applications. The chip, fabricated using 28 nm CMOS technology, comprises five main modules: an ARM processor for digital signal processing, delay cells for timing synchronization, ADC for sampling analog signals from monitors, OPAMP for signal amplification, and DAC for generating the required voltage for phase or intensity modulators. According to the simulations, the minimum delay is 11ps, the open-loop gain of the operational amplifier is 86.2 dB, the sampling rate of the ADC reaches 50 MHz, and the DAC achieves a high rate of 100 MHz. To the best of our knowledge, this marks the first design and evaluation of a fully integrated driver chip for QKD, holding the potential to significantly enhance QKD system performance. Thus, we believe our work could inspire future investigations toward the development of more efficient and reliable QKD systems.

Entropy•Apr 29, 2024•0 citations
An ASIC is presented in this paper for discriminating signal from single photon detector (SPD) of high-speed quantum key distribution (QKD) system. The circuit is designed in 130 nm CMOS process. It receives and discriminates a small voltage pulse from a SPD, coinciding with a trigger signal and outputs the effective signal to next stage of QKD system. The pulse width of the voltage signal from SPD is less than 400 ps. The circuit mainly consists of bandgap reference, high speed comparator, delay chain and current mode logic (CML) driver. It should operate at a speed of 1.25 GHz. This work integrate all the front-end electronics for SPD into a chip. The area, stray capacitance and power consumption of the whole circuit are reduced. And then the whole receiver of QKD system can be integrated into a chip to improve performance.
The single photon source is an important part of the quantum key distribution (QKD) system. At present, the single photon source is large in size and complex in structure for a lot of discrete components which are used. The miniaturization of the photon source is the tendency of the QKD system. We integrate all laser driver electronic module into one single ASIC chip, which can be used to drive the 1550nm DFB laser in random pulse mode and it can greatly reduce the volume of the single photon source. We present the design of the chip named LSD2018 and simulation results before the tape-out. The LSD2018 is fabricated with a 130 nm CMOS process and consists of a discriminator, an adjustable pulse generator, a bandgap reference, an SPI bus, and an amplitude-adjustable current pulse driver. The electronic random pulse from the driver can go 20mA to 120mA in amplitude and 400ps to 4ns in pulse width. The parameters can be set by an SPI bus.
A commercial avalanche photodiode (APD) and the circuitry needed to operate it as a single-photon detector (SPD) have been integrated onto a single PC board (PCB). At temperatures accessible with Peltier coolers (∼200–240 K), the PCB-SPD achieves high detection efficiency (DE) at 1308 and 1545 nm with low dark-count probability (e.g. ∼10−6/bias pulse at DE = 20%, 220 K), making it useful for quantum key distribution (QKD). The board generates fast bias pulses, cancels noise transients, amplifies the signals, and sends them to an on-board discriminator. A digital blanking circuit suppresses afterpulsing.
Abstract Quantum key distribution (QKD) achieves information-theoretic security based on quantum mechanics principles, where single-photon detectors (SPDs) serve as critical components. This study focuses on the sinusoidal gated SPDs widely used in high-speed QKD systems. We investigate the mechanisms underlying the rising-edge jitter in detection signals, identifying contributions from factors such as the temporal width of injected optical pulses, avalanche generation processes, avalanche signal extraction, and pulse discrimination. To address the issue of excessive jitter-induced bit errors, we propose a retiming scheme that utilizes coincidence signals synchronized with the sinusoidal gating signal. This approach effectively suppresses detection signal jitter and reduces the after-pulse probability of the detector. Experimental validation using a high-precision time-to-digital converter (TDC) demonstrates a significant reduction in the rising-edge jitter distribution after applying the suppression scheme. The proposed method features clear principles and straightforward engineering implementation, avoiding direct interference with the detector’s operational processes. The designed high-speed sinusoidal gated InGaAs/InP SPD operates at 1.25 GHz, achieving a remarkable reduction in after-pulse probability from 10.7% (without jitter suppression) to 0.72%, thereby enhancing the overall performance of QKD systems.
Integrated photonics has the advantages of miniaturization, low cost, and CMOS compatibility, and it provides a stable, highly integrated, and practical platform for quantum key distribution (QKD). While photonic integration of optical components has greatly reduced the overall cost of QKD systems, single-photon detectors (SPDs) have become the most expensive part of a practical QKD system. In order to circumvent this obstacle and make full use of SPDs, we have designed and fabricated a QKD receiver chip for multiple users. Our chip is based on a time-division multiplexing technique and makes use of a single set of SPDs to support up to four users' QKD. Our proof-of-principle chip-based QKD system is capable of producing an average secret key rate of 13.68 kbps for four users with a quantum bit error rate (QBER) as low as 0.51% over a simulated distance of 20 km in fiber. Our result clearly demonstrates the feasibility of multiplexing SPDs for setting QKD channels with different users using photonic integrated chip and may find applications in the commercialization of quantum communication technology.
In our experiment, two InGaAs/InP avalanche photodiodes (APD) were used in the quantum key distribution (QKD) system for single-photon detection at telecom communication wavelength (1310/1550 nm). By using properly designed passive-quenching circuit, the photo-detection efficiency of the APD could reach 10% at 1550 nm. In order to decrease the dark count rate efficiently, we designed a coincident counting circuits for single-photon detection. Before the APD signals were sent to the signal processing circuit, the avalanche signals were amplified and shaped into the TTL pulses. In order to obtain an accurate and efficient data acquisition and to transfer synchronically several signals such as the TTL signals and pulses from Random generators, we designed a signal processing circuit with the parallel port whose speed limitation is about 100Kb/s. In our experiments of single-photon interference and quantum cryptography, the electronic designs presented us satisfactory performance and results. To achieve much higher speed for the data acquisition, we also employed the Universal Serial Bus System (USB2.0) to interface our single-photon avalanche detectors and random generators used in our QKD system, which was believed to improve the performance of QKD such as the key distribution speed.
Quantum Key Distribution (QKD) has garnered significant attention due to its unconditional security based on the fundamental principles of quantum mechanics. While QKD has been demonstrated by various groups and commercial QKD products are available, the development of a fully chip-based QKD system, aimed at reducing costs, size, and power consumption, remains a significant technological challenge. Most researchers focus on the optical aspects, leaving the integration of the electronic components largely unexplored. In this paper, we present the design of a fully integrated electrical control chip for QKD applications. The chip, fabricated using 28 nm CMOS technology, comprises five main modules: an ARM processor for digital signal processing, delay cells for timing synchronization, ADC for sampling analog signals from monitors, OPAMP for signal amplification, and DAC for generating the required voltage for phase or intensity modulators. According to the simulations, the minimum delay is 11ps, the open-loop gain of the operational amplifier is 86.2 dB, the sampling rate of the ADC reaches 50 MHz, and the DAC achieves a high rate of 100 MHz. To the best of our knowledge, this marks the first design and evaluation of a fully integrated driver chip for QKD, holding the potential to significantly enhance QKD system performance. Thus, we believe our work could inspire future investigations toward the development of more efficient and reliable QKD systems.