Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Photonics Technology Letters

Remotely Gated InGaAs Single-Photon Detector at 1550 nm

Giselle Silva Castro, Joacir Soares de Andrade, Ranara Louise Campos Damasceno, João Batista Rosa Silva, Rubens Viana Ramos

Published Dec 19, 2019• 3 citations
Publisher

Abstract

Single-photon detectors (SPDs) are important devices in the development of quantum technologies, like quantum metrology, quantum computers and quantum communication. The simplest, cheapest and most commonly used SPD employs avalanche photodiode. After the photon absorption, a photocurrent is produced and it must be quenched before to damage the device. In the present work we show a new strategy for quenching the photocurrent of avalanche photodiodes remotely. Our scheme makes easier the synchronism between sender and receiver in a quantum communication setup. Some experimental results are presented.

DOI
10.1109/lpt.2019.2960773

Related papers

Advances in InGaAs/InP single-photon detector systems for quantum communication

Jun Zhang, Mark A. Itzler, Hugo Zbinden +1 more

Single-photon detectors (SPDs) are the most sensitive instruments for light detection. In the near-infrared range, SPDs based on III–V compound semiconductor avalanche photodiodes have been extensively used during the past two decades for diverse applications due to their advantages in practicality including small size, low cost and easy operation. In the past decade, the rapid developments and increasing demands in quantum information science have served as key drivers to improve the device performance of single-photon avalanche diodes and to invent new avalanche quenching techniques. This Review aims to introduce the technology advances of InGaAs/InP single-photon detector systems in the telecom wavelengths and the relevant quantum communication applications, and particularly to highlight recent emerging techniques such as high-frequency gating at GHz rates and free-running operation using negative-feedback avalanche diodes. Future perspectives of both the devices and quenching techniques are summarized. Recent progress in single-photon detectors for quantum communication based on III–V compound semiconductor avalanche photodiodes is reviewed. Specifically, Jun Zhang and Jian-Wei Pan at the University of Science and Technology of China and their colleagues in the USA and Switzerland introduce technological advances for InGaAs/InP single-photon detector systems in the telecommunication band along with their associated applications in quantum communication. III–V single-photon avalanche diodes are the most practical tools available for detecting ultraweak near-infrared light. The scientists overview important parameters for evaluating the performance of detector systems based on single-photon avalanche diodes and describe the experimental characterization of these parameters. They also consider emerging techniques, including high-frequency gating at gigahertz rates and free-running operation using negative-feedback avalanche diodes. Finally, the future prospects of these devices are considered.

arXiv:1501.06261•Light Science & Applications•May 8, 2015•470 citations

Single-photon detector at 1550 nm with gate-mode quenched InGaAs/InP avalanche photodiode

Guang Wu, Chunyuan Zhou, Xiuliang Chen +2 more

In our recent experiment, we have designed a novel single-photon detecting module for quantum key distribution using an InGaAs/InP avalanche photodiode with gate-mode quenched photo-detection. At a repetition rate of 100 kHz and the working temperature of -60°C, we obtained the detection efficiency η higher than 10% and 20% at the dark probability Pd about 1.3×10-5 and 1.6×10-5 per nanosecond, respectively. Also at 100 kHz, we got the best ratio of Pd/η as 1.7×10-3 per pulse (20 ns). And at a lower repetition such as 10 kHz, we obtained Pd/η as 8.9×10-4 per pulse.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 12, 2004•2 citations

A single-photon detector for high-speed telecom-band quantum communication applications

Chuang Liang, Kim Fook Lee, Paul L. Voss +5 more

We present the design and construction of a high-speed telecom-band (1.5 μm) single-photon counting system based on an InGaAs/InP avalanche photodiode (APD) operating in the gated Geiger mode. The detector can be gated at high speeds (we examine its performance up to 25 MHz) to maximize the counting rate in long-distance, telecom-band, fiber-optic quantum communication applications. Narrow gate pulses (250 ps full width at half maximum) are used to reduce the dark-count and the after-pulse probability. In order to count the avalanche events, we employ a high-speed comparator to sample the unfiltered and unamplified avalanche photocurrent. The APD and all the associated electronics are integrated onto a printed circuit board with a computer interface. In addition, we cool the APD to -27°C to reduce the dark-count probability.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Aug 18, 2005•6 citations

Single‐photon detector for long‐distance quantum cryptography

Naoto Namekata, Yuuki Makino, Shuichiro Inoue

Abstract In order to realize long‐distance quantum cryptography based on standard optical fiber network, we have developed a single‐photon detector at 1550 nm using InGaAs/InP avalanche photodiodes (APDs). To reduce the dark count probability, APDs were cooled and operated with a Gated Passive Quenching Circuit. A quantum efficiency of 13.7% was obtained at −55 °C while keeping the dark count probability per gate (2 ns) as low as 2.4 × 10−5. In this paper we will discuss the performance of the developed single‐photon detector in view of application to quantum cryptography. © 2003 Wiley Periodicals, Inc. Electron Comm Jpn Pt 2, 86(5): 10–15, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/ecjb.10115

Electronics and Communications in Japan (Part II Electronics)•Apr 4, 2003•0 citations

Single-photon detectors for long distance quantum communications

Elena Anisimova

Quantum communications and quantum cryptography are developing rapidly during the last decades caused partly by a fast progress in quantum computing. Quantum cryptography provides an unconditionally secure way of communicating whereas traditional classical cryptographic protocols are likely to be broken by super powerful quantum computers. In the past few years distances covered by quantum communications have increased by an order of magnitude. To provide a global coverage for the quantum networks, a satellite based quantum communications is the most promising solution. \n \nAs an emerging field, QKD systems are still under evolution process. Despite outstanding security proven theoretically, it has loopholes caused by their implementations. To test QKD, find the possible loopholes and suggest ways to fix them, is a job of many scientific groups. \nIn this thesis I start with presenting my work for a securing test of a commercial QKD system Clavis2. A Trojan-horse attack on Bob's apparatus was prepared by testing reflections and transmissions of all optical components in Bob's scheme. The attack was implemented and found to be unsuccessful at the tested wavelengths due to afterpulsing effect in Bob's single-photon detectors reacting to the bright light attack pulses. \n \nThree chapters of the thesis are dedicated to custom built single-photon detectors (SPDs) based on commercial Silicon avalanche photodiodes (APDs). Those detectors demonstrate parameters that altogether are not possible to find in commercially available SPDs, especially if combined with a very compact size. One of the in-lab-built SPDs was implemented in 143 km teleportation experiment, where a low dark count rate was crucial for the success of the experiment. The next generation SPD is already built, characterized and ready to be implemented. \n \nAnother 4-channel SPD was built as a prototype for a quantum satellite SPD. It has light weight, low electrical power consumption, low dark count rate and decent other parameters. It was used in the airborne demonstration of QKD receiver payload experiment, when a secret key was successfully generated between a moving aircraft and a ground station. \n \nSPDs installed on a satellite have to be able to work in the harsh space environment during a mission life time. Space radiation dramatically increases dark count rate of APDs. The last project presented in the thesis committed to a radiation test of three types of APDs and one type of photo multiplier tube. The experiment included characterization of all SPDs before and after irradiation by four levels of proton radiation, equivalent to 3 months - 2 years duration in a 600 km low Earth orbit. Three methods for mitigating radiation damage were tested and found to be successful with perspective to use some of them on a quantum satellite to extent life time of SPDs. \n \nTo summarize, this work makes a contribution to the development of SPDs for global quantum communications.

•Jan 23, 2018•2 citations

Single-photon detectors for practical quantum cryptography

Alberto Tosi, Franco Zappa, S. Cova

The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 19, 2012•15 citations
Single-photon detectors (SPDs) are important devices in the development of quantum technologies, like quantum metrology, quantum computers and quantum communication. The simplest, cheapest and most commonly used SPD employs avalanche photodiode. After the photon absorption, a photocurrent is produced and it must be quenched before to damage the device. In the present work we show a new strategy for quenching the photocurrent of avalanche photodiodes remotely. Our scheme makes easier the synchronism between sender and receiver in a quantum communication setup. Some experimental results are presented.
Single-photon detectors (SPDs) are the most sensitive instruments for light detection. In the near-infrared range, SPDs based on III–V compound semiconductor avalanche photodiodes have been extensively used during the past two decades for diverse applications due to their advantages in practicality including small size, low cost and easy operation. In the past decade, the rapid developments and increasing demands in quantum information science have served as key drivers to improve the device performance of single-photon avalanche diodes and to invent new avalanche quenching techniques. This Review aims to introduce the technology advances of InGaAs/InP single-photon detector systems in the telecom wavelengths and the relevant quantum communication applications, and particularly to highlight recent emerging techniques such as high-frequency gating at GHz rates and free-running operation using negative-feedback avalanche diodes. Future perspectives of both the devices and quenching techniques are summarized. Recent progress in single-photon detectors for quantum communication based on III–V compound semiconductor avalanche photodiodes is reviewed. Specifically, Jun Zhang and Jian-Wei Pan at the University of Science and Technology of China and their colleagues in the USA and Switzerland introduce technological advances for InGaAs/InP single-photon detector systems in the telecommunication band along with their associated applications in quantum communication. III–V single-photon avalanche diodes are the most practical tools available for detecting ultraweak near-infrared light. The scientists overview important parameters for evaluating the performance of detector systems based on single-photon avalanche diodes and describe the experimental characterization of these parameters. They also consider emerging techniques, including high-frequency gating at gigahertz rates and free-running operation using negative-feedback avalanche diodes. Finally, the future prospects of these devices are considered.
In our recent experiment, we have designed a novel single-photon detecting module for quantum key distribution using an InGaAs/InP avalanche photodiode with gate-mode quenched photo-detection. At a repetition rate of 100 kHz and the working temperature of -60°C, we obtained the detection efficiency η higher than 10% and 20% at the dark probability Pd about 1.3×10-5 and 1.6×10-5 per nanosecond, respectively. Also at 100 kHz, we got the best ratio of Pd/η as 1.7×10-3 per pulse (20 ns). And at a lower repetition such as 10 kHz, we obtained Pd/η as 8.9×10-4 per pulse.
We present the design and construction of a high-speed telecom-band (1.5 μm) single-photon counting system based on an InGaAs/InP avalanche photodiode (APD) operating in the gated Geiger mode. The detector can be gated at high speeds (we examine its performance up to 25 MHz) to maximize the counting rate in long-distance, telecom-band, fiber-optic quantum communication applications. Narrow gate pulses (250 ps full width at half maximum) are used to reduce the dark-count and the after-pulse probability. In order to count the avalanche events, we employ a high-speed comparator to sample the unfiltered and unamplified avalanche photocurrent. The APD and all the associated electronics are integrated onto a printed circuit board with a computer interface. In addition, we cool the APD to -27°C to reduce the dark-count probability.
Abstract In order to realize long‐distance quantum cryptography based on standard optical fiber network, we have developed a single‐photon detector at 1550 nm using InGaAs/InP avalanche photodiodes (APDs). To reduce the dark count probability, APDs were cooled and operated with a Gated Passive Quenching Circuit. A quantum efficiency of 13.7% was obtained at −55 °C while keeping the dark count probability per gate (2 ns) as low as 2.4 × 10−5. In this paper we will discuss the performance of the developed single‐photon detector in view of application to quantum cryptography. © 2003 Wiley Periodicals, Inc. Electron Comm Jpn Pt 2, 86(5): 10–15, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/ecjb.10115
Quantum communications and quantum cryptography are developing rapidly during the last decades caused partly by a fast progress in quantum computing. Quantum cryptography provides an unconditionally secure way of communicating whereas traditional classical cryptographic protocols are likely to be broken by super powerful quantum computers. In the past few years distances covered by quantum communications have increased by an order of magnitude. To provide a global coverage for the quantum networks, a satellite based quantum communications is the most promising solution. \n \nAs an emerging field, QKD systems are still under evolution process. Despite outstanding security proven theoretically, it has loopholes caused by their implementations. To test QKD, find the possible loopholes and suggest ways to fix them, is a job of many scientific groups. \nIn this thesis I start with presenting my work for a securing test of a commercial QKD system Clavis2. A Trojan-horse attack on Bob's apparatus was prepared by testing reflections and transmissions of all optical components in Bob's scheme. The attack was implemented and found to be unsuccessful at the tested wavelengths due to afterpulsing effect in Bob's single-photon detectors reacting to the bright light attack pulses. \n \nThree chapters of the thesis are dedicated to custom built single-photon detectors (SPDs) based on commercial Silicon avalanche photodiodes (APDs). Those detectors demonstrate parameters that altogether are not possible to find in commercially available SPDs, especially if combined with a very compact size. One of the in-lab-built SPDs was implemented in 143 km teleportation experiment, where a low dark count rate was crucial for the success of the experiment. The next generation SPD is already built, characterized and ready to be implemented. \n \nAnother 4-channel SPD was built as a prototype for a quantum satellite SPD. It has light weight, low electrical power consumption, low dark count rate and decent other parameters. It was used in the airborne demonstration of QKD receiver payload experiment, when a secret key was successfully generated between a moving aircraft and a ground station. \n \nSPDs installed on a satellite have to be able to work in the harsh space environment during a mission life time. Space radiation dramatically increases dark count rate of APDs. The last project presented in the thesis committed to a radiation test of three types of APDs and one type of photo multiplier tube. The experiment included characterization of all SPDs before and after irradiation by four levels of proton radiation, equivalent to 3 months - 2 years duration in a 600 km low Earth orbit. Three methods for mitigating radiation damage were tested and found to be successful with perspective to use some of them on a quantum satellite to extent life time of SPDs. \n \nTo summarize, this work makes a contribution to the development of SPDs for global quantum communications.
The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.