The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.
The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.
InGaAs/InP single-photon avalanche diodes (SPADs) are widely used in practical applications requiring near-infrared photon counting such as quantum key distribution (QKD). Photon detection efficiency and dark count rate are the intrinsic parameters of InGaAs/InP SPADs, due to the fact that their performances cannot be improved using different quenching electronics given the same operation conditions. After modeling these parameters and developing a simulation platform for InGaAs/InP SPADs, we investigate the semiconductor structure design and optimization. The parameters of photon detection efficiency and dark count rate highly depend on the variables of absorption layer thickness, multiplication layer thickness, excess bias voltage, and temperature. By evaluating the decoy-state QKD performance, the variables for SPAD design and operation can be globally optimized. Such optimization from the perspective of specific applications can provide an effective approach to design high-performance InGaAs/InP SPADs.
In any quantum communication system, such as a quantum key distribution (QKD) system, data rates are mainly limited by the system clock rate and the various link losses. While the transmission clock rate is limited by the temporal resolution of the single-photon detectors, losses in a fiber-based quantum communication system can be minimized by operating in the near infrared range (NIR), at 1310 nm or 1550 nm. Commercially available InGaAs-based avalanche photo-diodes (APDs) can be operated as single-photon detectors in this wavelength range [Hadfield, 2009]. Due to the severe after-pulsing, InGaAs APDs are typically used in a gated mode and this can limit their application in high-speed quantum communications systems. Superconducting single-photon detectors (SSPDs) can work in the NIR wavelength range with good performance [Gol’tsman et al. 2001; Hadfield, 2009]. However, SSPDs require cryogenic temperatures, and are not widely available on the commercial market at present. In addition, InGaAs/InP based photomultiplier tubes (PMT) can operate in the NIR range, but its performance is limited by very low detection efficiency (1 % at 1600 nm) and large timing jitter (1.5 ns) [Hamamatsu, 2005]. Microchannel plates (MCP) are micro-capillary electron multipliers coated with an electron-emissive material and multiply photon-excited electrons from a photon cathode [Wiza, 1979]. MCPs usually have faster rise times and lower timing jitter than is achievable with PMTs. InGaAs MCPs can work in the NIR range. These MCPs, but are limited by low detection efficiency (~1 %) [Martin, J. & Hink P. 2003]. On the other hand, silicon based avalanche photo-diodes (Si APDs) are compact, relatively inexpensive, and can be operated at ambient temperatures with high detection efficiency and low noise in the visible or near-visible range. Unfortunately they do not work at wavelengths longer than 1000 nm. For those wavelengths, an up-conversion technique has been developed that uses sum-frequency generation (SFG) in a non-linear optical medium to convert the signal photons to a higher frequency (shorter wavelength) in the visible or near visible range. The up-converted photons can then be detected by a Si APD. Up-conversion detectors use commercially available components and devices, and are a practical solution for many applications in quantum communications. To date, several groups have successfully developed highly efficient up-conversion single-photon detectors in the nearinfrared range using periodically poled lithium niobate (PPLN) waveguides [Diamanti et al., 2005; Langrock et al., 2005; Thew et al., 2006; Tanzilli et al., 2005; Xu et al., 2007;] and bulk crystals [Vandevender & Kwiat, 2004].
The application of quantum key distribution (QKD) has raised particular demands for single-photon detectors. One of the most promising candidates at the low-loss optical fibre communications windows is the planar geometry InGaAs/InP single-photon avalanche diode. These detectors have been modelled, fabricated and characterised at 1.55 µm wavelength. Their performance in terms of single-photon detection efficiency, dark count rate, timing jitter and afterpulsing behaviour are reported and compared with the best commercially available, linear multiplication avalanche photodiodes operated in Geiger-mode. Their use in the application of QKD is discussed.
We provide a direct comparison between the InGaAs avalanche photodiode (APD) and the NbN superconducting single photon detector (SSPD) for applications in fiber-based quantum cryptography. The quantum efficiency and dark count rate were measured for each detector, and used to calculate the quantum bit error rate (QBER) and shared key rate for a QKD link. The results indicate that, despite low quantum efficiency, the speed of the SSPD makes it a superior detector for quantum information applications. Finally, we present results of an initial integration of an SSPD into a receiver node of the DARPA quantum network to perform quantum key distribution. Encoding quantum information on single photons has enabled the realization of a number of unique communication schemes such as the implementation of the BB84 protocol for quantum key distribution 1 and quantum dense coding. 2 Furthermore, the implementation of these schemes using photons at telecommunication wavelengths has permitted their extension to fiber optic networks, 3,4 drastically increasing the practicality of quantum information processing. To date, the state of the art in commercially available single photon detection at telecommunication wavelengths (1550 nm) has been the thermo-electrically cooled InGaAs avalanche photodiode (APD). The cooled InGaAs APD is generally operated at T = -60°C in the reverse-biased Geiger mode. Though these detectors have been successfully implemented in operating QKD links in optical fiber, the InGaAs APD suffers from afterpulsing effects that limit the key exchange rates. New SPD (single photon detector) technologies based on superconducting materials are emerging that hold tremendous promise for drastically increasing the photon counting rate and eliminating dark noise.57 The SSPD consists of a NbN thin film (t ∼ 5 nm) patterned into a narrow (w ∼ 100 nm) microstrip meander that is ∼ 500μm in length. The detector is cooled to T < 4K in a closed cycle refrigeration unit and a bias current I b is supplied to the device just below the superconducting critical current (I c ). When a photon is incident upon the microstrip superconductivity is broken in the region local to photon absorption and a normal state region is formed in the device. The current passing through the device causes a measurable voltage pulse in the detector that can be amplified and shaped to act as an input for traditional logic circuitry. Due to the unique electronic bandstructure in a superconducting material the intrinsic response time of the device is on the order of picoseconds, so that the repetition rate may be increased above 1 GHz 8 without being susceptible to afterpulsing effects that plague the InGaAs APD. 9 To make a direct comparison between the InGaAs APD and the SSPD both were placed in a SPD characterization testbed to measure quantum efficiency and dark count rate at a variety of bias conditions. The QBER for a QKD link is calculated from the measured parameters and then compared to requirements for a provably secure QKD link. Following detector characterization, one of the nodes of the DARPA Quantum Network operated by BBN Technologies 3 utilized an SSPD in the receiver to transmit key material. The demonstration provides an in situ comparison between the InGaAs APD, normally operated in the BBN link, and the SSPD.
Two approaches to single-photon detection at telecom wavelengths have been investigated, using semiconductor and superconductor technologies. The low temperature operation of free-running InGaAs/InP negative feedback avalanche diodes (NFADs) was studied, demonstrating that they can operate with an extremely low dark count rate, which opens up a host of new applications. Secondly, superconducting nanowire single-photon detectors (SNSPDs) based on amorphous materials were developed, fabricated and characterized. These detectors are highly attractive because they can achieve excellent attributes simultaneously, such as high efficiency, low noise, good temporal resolution, no afterpulsing and high count rates. Finally, it was demonstrated that the use of NFADs can enable record distance quantum key distribution (QKD) over 307 km of optical fiber. A next generation QKD system has been proposed and numerically analyzed, aiming at extending the record distance by an additional 100 km and increasing the state-of-the-art secret key rate by over an order of magnitude.
InGaAs/InP Single-Photon Avalanche Diodes (SPADs) are widely employed in quantum optics applications, particularly in Quantum Key Distribution (QKD), due to their high sensitivity in the near-infrared range. In QKD, low noise and high timing resolution are essential to ensure secure and high-rate key exchange. One of the main limitations of InGaAs/InP SPADs is afterpulsing, which degrades the quantum bit error rate (QBER), limits the maximum count rate, and can compromise both the security and throughput of QKD systems. Reducing afterpulsing is thus crucial for enabling high-speed, reliable quantum communication. We present a newly developed gating and quenching circuit that significantly reduces afterpulsing. The circuit is located entirely outside the detector package, maintaining compatibility with any InGaAs/InP SPAD, and supports both gated and free-running operation. Unlike integrated ASIC-based solutions, which offer low parasitics but are often limited by process constraints (e.g., low maximum voltages), our approach uses high-speed discrete components, allowing high excess bias operation and design flexibility. While discrete designs are typically more prone to parasitics, our compact layout effectively mitigates these effects and preserves signal integrity. Experimental results show a strong afterpulsing reduction compared to our current commercial module. Additionally, the measured SPAD current highlights that the avalanche is completely quenched in less than a nanosecond after sensing. Eventually, the small footprint of the design paves the way for a new generation of compact, low-afterpulsing InGaAs/InP SPAD modules suitable for high-performance quantum optics applications.