Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Planarized Process for Single-Flux-Quantum Circuits With Self-Shunted Nb/Nb$_{x}$Si$_{1-x}$/Nb Josephson Junctions

David I. Olaya, Manuel A. Castellanos-Beltran, Javier F. Pulecio, John P. Biesecker, Soroush Khadem, Lewitt Theodore, P. F. Hopkins, Paul D. Dresselhaus, Samuel P. Benz

Published Mar 16, 2019• 26 citations
Publisher

Abstract

We describe our process for fabricating single-flux-quantum circuits for applications in communications metrology, advanced computing, and quantum information. The process flow includes four superconducting metal layers, one junction layer, one palladium-gold bias resistor layer, and a contact pad layer. Planarization using chemical-mechanical polishing is performed on the two lower insulating layers. This process is based on Josephson junctions with niobium superconducting electrodes and self-shunted, amorphous niobium-doped silicon barriers on the insulating side near the metal-insulator transition. The barrier material is deposited by cosputtering silicon and niobium, with the junction properties controlled by the relative sputtering powers and the duration of the barrier deposition step. The profiles of the deposition rates across 3-in (76.2 mm) wafers give a corresponding radial profile of the critical current density Jcthat increases by ~46% from the center to the edge of the wafer. To characterize our process, we have measured and show data for niobium metal quality and its magnetic penetration depth, as well as for wire and via inductances, and for via critical currents. The uniformity of the junction critical current Icacross a wafer was measured on test chips with 2.7-μm-diameter junctions. Within a 5 mm × 5 mm area, the standard deviation of Icwas ~2% for chips near the center of the wafer and up to ~7% for chips near the edge. We also describe process improvements and innovations under development aimed at increasing circuit density and high-speed performance.

DOI
10.1109/tasc.2019.2900020

Related papers

Fabrication Process of Planarized Multi-Layer Nb Integrated Circuits

T. Satoh, K. Hinode, Hiroyuki Akaike +3 more

To improve the operating speed and density of Nb single-flux-quantum integrated circuits, we developed an advanced fabrication process based on NEC's standard process. We fabricated planarized six-Nb-layer circuit structures using this advanced process. This new structure has four Nb wiring layers for greater design flexibility. To shield the magnetic field produced by the DC bias current, the DC bias power supply layer was placed under the groundplane. The critical current density of the Josephson junction was 10 kA/cm/sup 2/. We fabricated and tested more than 10 wafers and demonstrated that the six-layer circuits were successfully planarized. We also confirmed insulation between each Nb layer and the reliability of superconducting contacts. This planarization did not significantly degrade the junction characteristics. We measured small spreads in the critical current of less than 2%. These results demonstrated the effectiveness of this advanced process based on mechanical-polishing planarization.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•41 citations

Digital circuits using self-shunted Nb/NbxSi1−x/Nb Josephson junctions

David I. Olaya, Paul D. Dresselhaus, Samuel P. Benz +5 more

Superconducting digital circuits based on Josephson junctions with amorphous niobium-silicon (a-NbSi) barriers have been designed, fabricated, and tested. Single-flux-quantum (SFQ) shift registers operated with ±30% bias margins, confirming junction reproducibility and uniformity. Static digital dividers operated up to 165 GHz for a single value of bias current, which was only marginally slower than circuits fabricated with externally shunted AlOx-barrier junctions having a comparable critical current density of 4.5 kA/cm2. In comparison, self-shunted a-NbSi junctions enabled a doubling in circuit density. This and their relatively thick 10 nm barriers could increase the yield of complex SFQ circuits.

Applied Physics Letters•May 24, 2010•24 citations

Single-flux-quantum circuits utilizing self-shunted NbN/TaN/NbN Josephson junctions grown on silicon substrates

Yulong Zhong, Lu Zhang, Junjie Xie +9 more

Abstract We report on the electrical properties of NbN/TaN/NbN Josephson junctions grown on thermally oxidized silicon substrates, along with the design and fabrication of superconducting single-flux-quantum (SFQ) circuits based on these NbN superconductor/normal metal/superconductor (SNS) junctions. The critical current density ( J c ) of the junctions was found to be relatively sensitive to the barrier thickness, decreasing from 108.0 ± 8.1 kA cm −2 for a 15 nm barrier to 12.8 ± 1.9 kA cm −2 for a 30 nm barrier. For a J c of approximately 24.5 ± 2.1 kA cm −2 and a barrier thickness of 25 nm, the NbN SNS junctions are self-shunted and exhibit nonhysteretic current–voltage ( I – V ) characteristics. Especially for junctions with diameter ( φ ) ranging from 0.8 to 1.6 μ m, their critical current ( I c ) falls within the range of 110–450 μ A, making them suitable for SFQ circuits. By considering the impact of excess current and incorporating it as an additional term in the conventional resistively and capacitively shunted junction model, the I – V curves of NbN SNS junctions can be precisely described, successfully minimizing the deviation between simulations and test results. The DC-SFQ and SFQ-DC interface circuits can both operate normally, and the bias margins of cell circuits such as Josephson transmission line, confluence buffer, D flip-flop, and splitter are greater than 40%. Compared to Nb superconductor/insulator/superconductor junctions, their self-shunting characteristics and relatively thick 25 nm barriers can also enhance the integration of circuits and increase the yield to complex circuits.

Superconductor Science and Technology•Oct 6, 2024•7 citations

Development of Self-Shunted Josephson Junctions for a Ten-Superconductor-Layer Fabrication Process: Nb/NbN x /Nb Junctions

Sergey K. Tolpygo, Ravi Rastogi, Terence J. Weir +2 more

To increase the integration scale of superconductor electronics, we are developing a new node, titled SFQ7ee, of the fabrication process at MIT Lincoln Laboratory. In comparison to the existing SFQ5ee node, we increased the number of fully planarized superconducting layers to ten and utilized NbN and NbN/Nb kinetic inductors to increase the possible inductor number density above a hundred million inductors per cm2. Increasing the Josephson junction number density to the same level requires implementing self-shunted high-JcJosephson junctions. We investigated the properties of Nb/NbNx/Nb trilayer junctions as a potential replacement of high-JcNb/Al-AlOx/Nb junctions, where NbNxis a disordered, overstoichiometric, nonsuperconducting nitride deposited by reactive sputtering. Dependences of theIcRnproduct and Josephson critical current density, Jc on the NbNx barrier thickness and temperature were studied in the thickness range from 5 nm to 20 nm. The fabricated junctions can be well described by the microscopic theory of SNS junctions, assuming no suppression of the energy gap in Nb electrodes near the NbNxinterfaces and a Cooper pair decay length in the NbNx barrier, ξnTcof about 2.3 nm. Current-voltage characteristics of the junctions are well described by the resistively and capacitively shunted junction (RCSJ) model without excess current. In the studied rangeJc2, the Nb/NbNx/Nb junctions have lower values of the specific resistanceRnA, lower IcRn products, and a stronger dependence of theIcRnon temperature than the self-shunted or critically damped externally shunted Nb/Al-AlOx/Nb junctions with the same critical current density; A is the junction area,Icthe junction critical current, and Rnthe effective shunting resistance.

arXiv:2312.13475•IEEE Transactions on Applied Superconductivity•Feb 9, 2024•14 citations

Development of 15kA/cm$^2$ Fabrication Process for Superconducting Integrated Digital Circuits

Liliang Ying, Xue Zhang, Guixiang He +7 more

A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 $Ω$, followed by the deposition of Nb/Al-AlO$_x$/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm$^2$. To increase the Al-AlO$_x$ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.

arXiv:2304.01588•Apr 4, 2023•2 citations

Fabrication and characterization of high-quality Nb/Al-AlO x /Nb cross-type Josephson tunnel junctions utilising CMP-based planarisation techniques

Alexander Stoll, Andreas Reifenberger, Daniel Hengstler +2 more

Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.

arXiv:2609.08569•Superconductor Science and Technology•Nov 10, 2026•0 citations
Planarized Process for Single-Flux-Quantum Circuits With Self-Shunted Nb/Nbx_{x}x​Si1−x_{1-x}1−x​/Nb Josephson Junctions
We describe our process for fabricating single-flux-quantum circuits for applications in communications metrology, advanced computing, and quantum information. The process flow includes four superconducting metal layers, one junction layer, one palladium-gold bias resistor layer, and a contact pad layer. Planarization using chemical-mechanical polishing is performed on the two lower insulating layers. This process is based on Josephson junctions with niobium superconducting electrodes and self-shunted, amorphous niobium-doped silicon barriers on the insulating side near the metal-insulator transition. The barrier material is deposited by cosputtering silicon and niobium, with the junction properties controlled by the relative sputtering powers and the duration of the barrier deposition step. The profiles of the deposition rates across 3-in (76.2 mm) wafers give a corresponding radial profile of the critical current density Jcthat increases by ~46% from the center to the edge of the wafer. To characterize our process, we have measured and show data for niobium metal quality and its magnetic penetration depth, as well as for wire and via inductances, and for via critical currents. The uniformity of the junction critical current Icacross a wafer was measured on test chips with 2.7-μm-diameter junctions. Within a 5 mm × 5 mm area, the standard deviation of Icwas ~2% for chips near the center of the wafer and up to ~7% for chips near the edge. We also describe process improvements and innovations under development aimed at increasing circuit density and high-speed performance.
To improve the operating speed and density of Nb single-flux-quantum integrated circuits, we developed an advanced fabrication process based on NEC's standard process. We fabricated planarized six-Nb-layer circuit structures using this advanced process. This new structure has four Nb wiring layers for greater design flexibility. To shield the magnetic field produced by the DC bias current, the DC bias power supply layer was placed under the groundplane. The critical current density of the Josephson junction was 10 kA/cm/sup 2/. We fabricated and tested more than 10 wafers and demonstrated that the six-layer circuits were successfully planarized. We also confirmed insulation between each Nb layer and the reliability of superconducting contacts. This planarization did not significantly degrade the junction characteristics. We measured small spreads in the critical current of less than 2%. These results demonstrated the effectiveness of this advanced process based on mechanical-polishing planarization.
Superconducting digital circuits based on Josephson junctions with amorphous niobium-silicon (a-NbSi) barriers have been designed, fabricated, and tested. Single-flux-quantum (SFQ) shift registers operated with ±30% bias margins, confirming junction reproducibility and uniformity. Static digital dividers operated up to 165 GHz for a single value of bias current, which was only marginally slower than circuits fabricated with externally shunted AlOx-barrier junctions having a comparable critical current density of 4.5 kA/cm2. In comparison, self-shunted a-NbSi junctions enabled a doubling in circuit density. This and their relatively thick 10 nm barriers could increase the yield of complex SFQ circuits.
Abstract We report on the electrical properties of NbN/TaN/NbN Josephson junctions grown on thermally oxidized silicon substrates, along with the design and fabrication of superconducting single-flux-quantum (SFQ) circuits based on these NbN superconductor/normal metal/superconductor (SNS) junctions. The critical current density ( J c ) of the junctions was found to be relatively sensitive to the barrier thickness, decreasing from 108.0 ± 8.1 kA cm −2 for a 15 nm barrier to 12.8 ± 1.9 kA cm −2 for a 30 nm barrier. For a J c of approximately 24.5 ± 2.1 kA cm −2 and a barrier thickness of 25 nm, the NbN SNS junctions are self-shunted and exhibit nonhysteretic current–voltage ( I – V ) characteristics. Especially for junctions with diameter ( φ ) ranging from 0.8 to 1.6 μ m, their critical current ( I c ) falls within the range of 110–450 μ A, making them suitable for SFQ circuits. By considering the impact of excess current and incorporating it as an additional term in the conventional resistively and capacitively shunted junction model, the I – V curves of NbN SNS junctions can be precisely described, successfully minimizing the deviation between simulations and test results. The DC-SFQ and SFQ-DC interface circuits can both operate normally, and the bias margins of cell circuits such as Josephson transmission line, confluence buffer, D flip-flop, and splitter are greater than 40%. Compared to Nb superconductor/insulator/superconductor junctions, their self-shunting characteristics and relatively thick 25 nm barriers can also enhance the integration of circuits and increase the yield to complex circuits.
To increase the integration scale of superconductor electronics, we are developing a new node, titled SFQ7ee, of the fabrication process at MIT Lincoln Laboratory. In comparison to the existing SFQ5ee node, we increased the number of fully planarized superconducting layers to ten and utilized NbN and NbN/Nb kinetic inductors to increase the possible inductor number density above a hundred million inductors per cm2. Increasing the Josephson junction number density to the same level requires implementing self-shunted high-JcJosephson junctions. We investigated the properties of Nb/NbNx/Nb trilayer junctions as a potential replacement of high-JcNb/Al-AlOx/Nb junctions, where NbNxis a disordered, overstoichiometric, nonsuperconducting nitride deposited by reactive sputtering. Dependences of theIcRnproduct and Josephson critical current density, Jc on the NbNx barrier thickness and temperature were studied in the thickness range from 5 nm to 20 nm. The fabricated junctions can be well described by the microscopic theory of SNS junctions, assuming no suppression of the energy gap in Nb electrodes near the NbNxinterfaces and a Cooper pair decay length in the NbNx barrier, ξnTcof about 2.3 nm. Current-voltage characteristics of the junctions are well described by the resistively and capacitively shunted junction (RCSJ) model without excess current. In the studied rangeJc2, the Nb/NbNx/Nb junctions have lower values of the specific resistanceRnA, lower IcRn products, and a stronger dependence of theIcRnon temperature than the self-shunted or critically damped externally shunted Nb/Al-AlOx/Nb junctions with the same critical current density; A is the junction area,Icthe junction critical current, and Rnthe effective shunting resistance.
Development of 15kA/cm2^22 Fabrication Process for Superconducting Integrated Digital Circuits
A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 ΩΩΩ, followed by the deposition of Nb/Al-AlOx_xx​/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm2^22. To increase the Al-AlOx_xx​ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.
Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.