Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2609.08569 · Superconductor Science and Technology

Fabrication and characterization of high-quality Nb/Al-AlO x /Nb cross-type Josephson tunnel junctions utilising CMP-based planarisation techniques

Alexander Stoll, Andreas Reifenberger, Daniel Hengstler, A. Fleischmann, C. Enss

Published Nov 10, 2026• 0 citations
arXivHTMLPDF

Abstract

Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.

DOI
10.1088/1361-6668/aec04c

Related papers

Anodization-free fabrication process for high-quality cross-type Josephson tunnel junctions based on a Nb/Al-AlO x /Nb trilayer

F Adam, C. Enss, Sebastian Kempf

Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.

arXiv:2403.01806•Superconductor Science and Technology•Jul 8, 2024•6 citations

Towards Fabrication of Sub-Micrometer Cross-Type Aluminum Josephson Junctions

Stephan Mechold, Katja Peiselt, Matthias Schmelz +5 more

The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.

IEEE Transactions on Applied Superconductivity•Dec 18, 2023•2 citations

Sub-micrometer-sized, cross-type Nb–AlOx–Nb tunnel junctions with low parasitic capacitance

Solveig Anders, Matthias Schmelz, Ludwig Fritzsch +4 more

We report on a technology for the fabrication of sub-micrometer sized cross-type Josephson tunnel junctions in niobium technology. We present the fabrication scheme and properties of cross-type junctions with linear dimensions from 10 down to 0.6 µm. Sidewall passivation of the junctions is achieved by anodization as well as by planarizing the junctions with SiO in a self-aligned deposition step. The measured ratio of the sub-gap resistance to the normal resistance is about 35. Because of their low sub-gap current and low parasitic capacitance such junctions are well suited for applications like high resolution SQUIDs.

Superconductor Science and Technology•May 14, 2009•58 citations

Characterization of Superconducting Josephson Junctions on Electro-Optic LiNbO 3 Substrates at mK Temperatures

Saba Kousar, Roberta Satariano, G. Ausanio +5 more

We report on the fabrication and millikelvin char acterization of Nb/Al–AlOx/Nb Josephson junctions directly de posited on X-cut LiNbO3 substrates. Motivated by the strong electro-optic and piezoelectric properties of LiNbO3, such devices are of interest for future hybrid superconducting–electro-optic architectures. The junctions were fabricated using standard processes involving DC magnetron sputtering followed by controlled thermal oxidation of the aluminum layer to form an AlOx tunnel barrier with reproducible junction areas. Insulation of the junctions was achieved by anodization and SiOx deposition. Electrical measurements performed at 30 mK reveal high-quality Josephson tunnel junction behavior with a critical current density ofJc= 70 A/cm2and a characteristic voltage reaching values up toVm= 286 mV. Differential conductance measurements exhibit pronounced quasiparticle peaks corresponding to a sum gap energy of 2Δ = (2.73 ± 0.05) meV, confirming the good quality of the Nb electrodes. Magnetic-field-dependent measure ments yield a Josephson penetration depth of λJ= 45 μm, confirming operation in the small-junction regime, with deviations from the ideal Josephson interference pattern attributed to non-uniform current distribution across the junction area. Compared to our previous characterization at 4.2 K, this work demonstrates reliable Josephson junction operation on LiNbO3 at dilution-refrigerator temperatures relevant for quantum circuits, supporting the suitability of lithium niobate as a promising substrate for future hybrid superconducting–electro-optic device implementations.

IEEE Transactions on Applied Superconductivity•Feb 23, 2026•0 citations

Fabrication of high-quality submicron Nb/Al-AlO x /Nb tunnel junctions

Haifeng Yu, Cao Wen-Hui, Zhu Xiao-Bo +6 more

Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.

Chinese Physics B•Aug 1, 2008•7 citations

Simplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits

Amr Osman, J. Simon, Andreas Bengtsson +7 more

We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.

arXiv:2011.05230•Applied Physics Letters•Feb 8, 2021•104 citations
Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.
Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.
The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.
We report on a technology for the fabrication of sub-micrometer sized cross-type Josephson tunnel junctions in niobium technology. We present the fabrication scheme and properties of cross-type junctions with linear dimensions from 10 down to 0.6 µm. Sidewall passivation of the junctions is achieved by anodization as well as by planarizing the junctions with SiO in a self-aligned deposition step. The measured ratio of the sub-gap resistance to the normal resistance is about 35. Because of their low sub-gap current and low parasitic capacitance such junctions are well suited for applications like high resolution SQUIDs.
We report on the fabrication and millikelvin char acterization of Nb/Al–AlOx/Nb Josephson junctions directly de posited on X-cut LiNbO3 substrates. Motivated by the strong electro-optic and piezoelectric properties of LiNbO3, such devices are of interest for future hybrid superconducting–electro-optic architectures. The junctions were fabricated using standard processes involving DC magnetron sputtering followed by controlled thermal oxidation of the aluminum layer to form an AlOx tunnel barrier with reproducible junction areas. Insulation of the junctions was achieved by anodization and SiOx deposition. Electrical measurements performed at 30 mK reveal high-quality Josephson tunnel junction behavior with a critical current density ofJc= 70 A/cm2and a characteristic voltage reaching values up toVm= 286 mV. Differential conductance measurements exhibit pronounced quasiparticle peaks corresponding to a sum gap energy of 2Δ = (2.73 ± 0.05) meV, confirming the good quality of the Nb electrodes. Magnetic-field-dependent measure ments yield a Josephson penetration depth of λJ= 45 μm, confirming operation in the small-junction regime, with deviations from the ideal Josephson interference pattern attributed to non-uniform current distribution across the junction area. Compared to our previous characterization at 4.2 K, this work demonstrates reliable Josephson junction operation on LiNbO3 at dilution-refrigerator temperatures relevant for quantum circuits, supporting the suitability of lithium niobate as a promising substrate for future hybrid superconducting–electro-optic device implementations.
Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.
We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.