Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Bulletin of the American Physical Society

Current-Biased SET-HBT Cryogenic Preamplifier for High-Fidelity Single-Shot Spin Readout

Matthew Curry, Andrew M. Mounce, Troy D. England, Ron Manginell, Joel R. Wendt, Tammy C. Pluym, Stephen M Carr, Malcolm S. Carroll

Published Mar 7, 2018• 0 citations
OpenAlex

Related papers

Single-Shot Readout of a S/T Qubit with a Cryogenic AC-Coupled HBT Amplifier in a Lithographic MOS Double Quantum Dot

Martin Rudolph, Troy D. England, Ryan Jock +10 more

Bulletin of the American Physical Society•Mar 7, 2018•0 citations

Integrated Cryogenic Current Comparators with dc SQUID readout for SET amplification

Elena Bartolomé, Jakob Flokstra, Horst Rogalla +4 more

•Sep 20, 2000•0 citations

Towards ultra-high single-shot readout fidelity of an electron spin qubit through an enhanced latching mechanism

Patrick Harvey-Collard, Benjamin D’Anjou, Jason Dominguez +7 more

Bulletin of the American Physical Society•Mar 14, 2017•0 citations

Flexible Low-power SiGe HBT Amplifier Circuits for Fast Single-shot Spin Readout

Troy D. England, Michael P Lilly, Matthew Curry +2 more

SAND2016-1807C  We want fast, high-fidelity, single-shot spin readout  Stand-alone SETs' SNR is too low at wide bandwidths  RF SETs require complex systems and extensive tuning  We continue to investigate cryogenic pre-amplification  Predictable, linear gain with low experiment overhead  Discrete COTS SiGe heterojunction bipolar transistors  New amplifier provides power-efficient, reliable gain Fast Single Shot Spin Readout Why Not HEMTs?Consistency  Variation in current versus input voltage  HBT ≈ 5 mV  HEMT ≈ 100 mV  This is an indicator for offsets in TIAs, ADCs, and DACs Why Not HEMTs?Output Current  Good design relies on constant current across output voltage  Flat lines are the goal  This is an indicator for maximum gain available in amplifiers  Unplotted: low frequency noise

Bulletin of the American Physical Society•Mar 16, 2016•1 citation

SiGe HBT cryogenic preamplification for higher bandwidth donor spin read-out

Matthew Curry, Stephen M Carr, Greg Ten-Eyck +4 more

Bulletin of the American Physical Society•Mar 6, 2014•0 citations

Single-Shot Readout Performance of Two Heterojunction-Bipolar-Transistor Amplification Circuits at Millikelvin Temperatures

Matthew Curry, M. Rudolph, Troy D. England +12 more

Abstract High-fidelity single-shot readout of spin qubits requires distinguishing states much faster than the T 1 time of the spin state. One approach to improving readout fidelity and bandwidth (BW) is cryogenic amplification, where the signal from the qubit is amplified before noise sources are introduced and room-temperature amplifiers can operate at lower gain and higher BW. We compare the performance of two cryogenic amplification circuits: a current-biased heterojunction bipolar transistor circuit (CB-HBT), and an AC-coupled HBT circuit (AC-HBT). Both circuits are mounted on the mixing-chamber stage of a dilution refrigerator and are connected to silicon metal oxide semiconductor (Si-MOS) quantum dot devices on a printed circuit board (PCB). The power dissipated by the CB-HBT ranges from 0.1 to 1 μ W whereas the power of the AC-HBT ranges from 1 to 20 μ W. Referred to the input, the noise spectral density is low for both circuits, in the 15 to 30 fA/ $$\sqrt{{\bf{Hz}}}$$ Hz range. The charge sensitivity for the CB-HBT and AC-HBT is 330 μ e/ $$\sqrt{{\bf{Hz}}}$$ Hz and 400 μ e/ $$\sqrt{{\bf{Hz}}}$$ Hz , respectively. For the single-shot readout performed, less than 10 μ s is required for both circuits to achieve bit error rates below 10 −3 , which is a putative threshold for quantum error correction.

arXiv:1901.04570•Scientific Reports•Nov 18, 2019•31 citations
SAND2016-1807C  We want fast, high-fidelity, single-shot spin readout  Stand-alone SETs' SNR is too low at wide bandwidths  RF SETs require complex systems and extensive tuning  We continue to investigate cryogenic pre-amplification  Predictable, linear gain with low experiment overhead  Discrete COTS SiGe heterojunction bipolar transistors  New amplifier provides power-efficient, reliable gain Fast Single Shot Spin Readout Why Not HEMTs?Consistency  Variation in current versus input voltage  HBT ≈ 5 mV  HEMT ≈ 100 mV  This is an indicator for offsets in TIAs, ADCs, and DACs Why Not HEMTs?Output Current  Good design relies on constant current across output voltage  Flat lines are the goal  This is an indicator for maximum gain available in amplifiers  Unplotted: low frequency noise
Abstract High-fidelity single-shot readout of spin qubits requires distinguishing states much faster than the T 1 time of the spin state. One approach to improving readout fidelity and bandwidth (BW) is cryogenic amplification, where the signal from the qubit is amplified before noise sources are introduced and room-temperature amplifiers can operate at lower gain and higher BW. We compare the performance of two cryogenic amplification circuits: a current-biased heterojunction bipolar transistor circuit (CB-HBT), and an AC-coupled HBT circuit (AC-HBT). Both circuits are mounted on the mixing-chamber stage of a dilution refrigerator and are connected to silicon metal oxide semiconductor (Si-MOS) quantum dot devices on a printed circuit board (PCB). The power dissipated by the CB-HBT ranges from 0.1 to 1 μ W whereas the power of the AC-HBT ranges from 1 to 20 μ W. Referred to the input, the noise spectral density is low for both circuits, in the 15 to 30 fA/ Hz\sqrt{{\bf{Hz}}}Hz​ Hz range. The charge sensitivity for the CB-HBT and AC-HBT is 330 μ e/ Hz\sqrt{{\bf{Hz}}}Hz​ Hz and 400 μ e/ Hz\sqrt{{\bf{Hz}}}Hz​ Hz , respectively. For the single-shot readout performed, less than 10 μ s is required for both circuits to achieve bit error rates below 10 −3 , which is a putative threshold for quantum error correction.