Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physical Review Letters

Laser Power Stabilization beyond the Shot Noise Limit Using Squeezed Light

H. Vahlbruch, D. M. Wilken, Moritz Mehmet, B. Willke

Published Oct 22, 2018• 64 citations
Publisher

Abstract

High levels of laser power stability are necessary for high precision metrology applications. The classical limit for the achievable power stability is determined by the shot noise of the light used to generate a power control signal. Increasing the power of the detected light reduces the relative shot noise level and allows higher stabilities. However, sufficiently high power is not always available and the detection of high laser powers is challenging. Here, we demonstrate a nonclassical way to improve the achievable power stability without increasing the detected power. By the injection of a squeezed vacuum field of light we improve the classical laser power stability beyond its shot noise limit by 9.4_{-0.6}^{+0.6} dB at Fourier frequencies between 5 and 80 kHz. For only 90.6 μA of detected photocurrent we achieve a relative laser power noise of 2.0_{-0.1}^{+0.1}×10^{-8}/sqrt[Hz]. This is the first demonstration of a squeezed light-enhanced laser power stabilization and its performance is equivalent to an almost tenfold increase of detected laser power in a classical scheme. The analysis reveals that the technique presented here has the potential to achieve stability levels of 4.2×10^{-10}/sqrt[Hz] with 58 mA photocurrent measured on a single photodetector.

DOI
10.1103/physrevlett.121.173601

Related papers

Bright squeezed light generation via nonclassical power stabilization

Jasper R. Venneberg, H. Vahlbruch, Marina Trad Nery +1 more

Low-power-noise lasers are essential for many high-precision experiments. Shot noise imposes a fundamental limit on the power stability achievable with classical light sources. In this Letter, we report the generation of bright squeezed light in the audio band, which can improve the sensitivity of otherwise shot-noise-limited measurements. The bright squeezed light source is experimentally realized via the use of squeezed vacuum in a power stabilization scheme. We demonstrate a laser beam at a power of 9.9 mW with a broadband power noise suppression below the classical stabilization limit by up to 8 . 7 − 0.4 + 0.3 dB in the audio band, resulting in a bright squeezed beam with a power noise of 5 . 7 − 0.4 + 0.3 dB below shot noise for frequencies from 6 kHz to 20 kHz. We further conceptually outline a method to surpass this result in the future.

Physical Review Research•May 20, 2025•7 citations

Mechanism of suppressing noise intensity of squeezed state enhancement

Ruotao ZHANG, Wenhui Zhang

This research focuses on advanced noise suppression technologies for high-precision measurement systems, particularly addressing the limitations of classical noise reducing approaches. The noise level of laser sources is a crucial factor that directly affects the measurement sensitivity in applications such as gravitational wave detection and biomedical imaging. Classical feedback control technologies are effective but often encounter a bottleneck resulting from the classical noise suppression limits. To cope with these challenges, a novel method integrating quantum squeezed light with classical feedback control systems to reduce intensity noise is proposed in this work. By employing an amplitude-squeezed light field, a quantum-enhanced feedback control model is developed, thereby theoretically examining the influence of both the feedback loop gain and the degree of squeezing on the noise suppression performance. The results show that the injection of squeezed light significantly reduces the intensity noise, approaching the shot noise limit (SNL), thereby improving the system sensitivity beyond the classical noise reduction boundaries. Specifically, –10 dB squeezed state injection into the feedback system yields an additional noise suppression of approximately 8.97 dB, exceeding what is achievable using classical feedback alone. This demonstrates that the potential of the proposed method can enhance measurement precision close to the quantum noise limits without increasing the laser power. The analysis highlights the asymmetric noise suppression effects between the inner feedback loop and outer feedback loop. Although the outer loop benefits significantly from the squeezed light injection and achieves noise levels that are unattainable by classical feedback methods, the inner loop shows relatively minor improvements. This asymmetry is attributed to the inherent characteristics of quantum squeezing and the limitations of the feedback loop design. Further investigation into the individual noise components reveals that the primary contributors to the intensity noise include input noise, photodetector noise, and beam splitter-induced vacuum fluctuations. The injection of squeezed light effectively mitigates these vacuum fluctuations, which are typically a major noise source in high-precision laser systems. Theoretical research results show that the use of squeezed light in feedback control systems can effectively enhance noise suppression, equivalent to a nine fold increase in detected optical power, without the physical drawbacks of increasing laser power such as thermal noise. In conclusion, this study provides a theoretical validation of combining quantum squeezed states with classical feedback control to exceed classical noise suppression limits. The integration of a –10 dB squeezed state demonstrates a significant noise reduction, showing that this hybrid approach could revolutionize noise management in precision measurement applications. The results pave the way for further exploring quantum-enhanced control technologies in fields such as gravitational wave detection, quantum communication, and advanced optical sensing, providing a pathway for improving sensitivity and noise suppression without increasing additional power requirements.

Acta Physica Sinica•Jan 1, 2025•2 citations

Beyond the quantum limit : a squeezed-light laser in GEO 600

Khalaidovski, Aleksandr

Albert Einstein's General Theory of Relativity predicts the existence of ripples in space- time, the so-called gravitational waves (GWs). In the past two decades, an international array of ground-based, kilometer-scale Michelson interferometers has been set up aiming at a rst observation. These Earth-bound GW detectors target signals at audio frequen- cies in a band of ca. 10 Hz { 10 kHz. At Fourier frequencies above 1 kHz, their sensitivity is limited by quantum noise. This shot-noise arises from the zero-point uctuations of the electromagnetic eld, the so-called vacuum uctuations , which enter the interferometer through its anti-symmetric signal port. Future generations of GW observatories will even be limited by quantum noise almost over their entire detection band [ ET ]. A `classical' solution to further improve the signal-to-shot-noise ratio (SNR) of the observatories consists in an increase of the circulating light power. A higher optical load inside the interferometer will, however, lead to thermally-induced beam distortion as well as to an increased radiation pressure noise level. This will eectively result in an upper limit for the optical light power employable in future GW observatory generations. An alternative approach to improve the SNR is based on the injection of so-called squeezed states of light. Such a light eld has a characteristic non-classical noise distribution in the eld quadratures. Injected from the signal port, the squeezed state replaces the vacuum state, thereby reducing the interferometer's quantum noise. The rst part of this thesis discusses the setup of a squeezed-light laser for the German- British GW observatory GEO 600. During characterization of the device, a noise reduc- tion of up to 9.6 dB below the vacuum noise level was observed in the frequency band of 10 Hz {10 kHz, setting a new benchmark for squeezing observed at audio frequencies. Corrected for detection losses, this value furthermore corresponds to more than 11 dB of squeezing available for injection into the dark port of GEO 600. Situated on a 1 : 15 m 1 : 35 m optical breadboard, the device features transportability and can be operated independently of the GW interferometer. A key feature of the squeezed-light laser is its unprecedented long-term stability. The longest characterization measurements lasted for 20 h with an overall duty cycle of more than 99 %. In the second part of this thesis, the implementation of squeezed light into GEO 600 is presented along with the results achieved. The observatory shot noise was reduced by up to 3.4 dB, corresponding to an improvement in sensitivity by a factor of up to 1.5. For isotropically distributed GW sources, this corresponds to an increase in detection probability by 1.5 3 3.4. This makes GEO 600 the rst large-scale GW interferometer with a non-classically enhanced sensitivity. Based on the performance of the squeezed- light laser, a sensitivity improvement by a factor of two, corresponding to an equivalent optical power increase by a factor of four, seems feasible in the near future.

•Jan 1, 2011•9 citations

Increasing the optical power in sub-shot noise precision measurements of absorption

Jonathan C. F. Matthews

The optical shot-noise limit of a laser beam represents the classical limit in precision and signal to noise ratio achievable in optical sensors and imaging systems. It is known that quantum states of light, such as squeezed light and quantum correlated twin beams can be used to enhance precision and signal to noise ratio to beyond this limit. This promises optical sensors with fundamentally superior performance to the state of the art. While quantum-enhanced signal to noise ratio has been demonstrated with macroscopic powers of squeezed probe beam, demonstrations of quantum enhanced precision have remained at extremely low powers of light (femto-Watts). Here we will give examples where increasing SNR with quantum light is not sufficient to increase precision and we will review proof of principle experiments that have demonstrated sub shot noise precision, including for absorption spectroscopy and imaging. We will also report our efforts to achieve this sub-shot-noise precision performance for transmission measurement with ~0.1mW of average probe power, equating to ~10W peak power in a pulsed experiment. Time permitting, we will discuss how integrated optics and integrated electronics enables 10s GHz bandwidth in the detection of squeezed light, for integrated quantum sensor technology.

Emerging Imaging and Sensing Technologies for Security and Defence; and Advanced Manufacturing Technologies for Micro- and Nanosystems in Security and Defence•Sep 18, 2020•0 citations

High-precision cavity spectroscopy using high-frequency squeezed light

J. Junker, D. M. Wilken, Elanor H. Huntington +1 more

In this article, we present a novel spectroscopy technique that improves the signal-to-shot-noise ratio without the need to increase the laser power. Detrimental effects by technical noise sources are avoided by frequency-modulation techniques (frequency up-shifting). Superimposing the signal on non-classical states of light leads to a reduced quantum noise floor. Our method reveals in a proof-of-concept experiment small signals at Hz to kHz frequencies even below the shot noise limit. Our theoretical calculations fully support our experimental findings. The proposed technique is interesting for applications such as high-precision cavity spectroscopy, e.g., for explosive trace gas detection where the specific gas might set an upper limit for the laser power employed.

Optics Express•Jan 15, 2021•13 citations

Stabilization improvement of the squeezed optical fields using a high signal-to-noise ratio bootstrap photodetector

Xiaoli Wang, Liang Wu, Shaocong Liang +6 more

High-precision cavity locking is crucial for squeezing optical fields. Here, a bootstrapped low-noise photodetector is utilized in the generation process of the squeezed state of light. This process is based on a combination of a modified trans-impedance amplifier (TIA) circuit and a two-stage bootstrap amplifier circuit. This not only achieves high-precision and long-term stable locking of the optical cavity, but it also improves the degree to which the light field is squeezed. The experiment results show that the detector has a high signal-to-noise ratio (SNR) of 26.7 dB at the analysis frequency of 3 MHz when measuring the shot noise with an injection optical power of 800 µW, and the equivalent optical power noise level is lower than 2.4 pW/Hz in the frequency range of 1-30 MHz. Moreover, the squeezing degree of the quadrature amplitude squeezed state light field can be improved by more than 34.9% when the detector is used for optical cavity locking. The photodetector is useful in continuous variable (CV) quantum information research.

Optics Express•Dec 5, 2022•5 citations
High levels of laser power stability are necessary for high precision metrology applications. The classical limit for the achievable power stability is determined by the shot noise of the light used to generate a power control signal. Increasing the power of the detected light reduces the relative shot noise level and allows higher stabilities. However, sufficiently high power is not always available and the detection of high laser powers is challenging. Here, we demonstrate a nonclassical way to improve the achievable power stability without increasing the detected power. By the injection of a squeezed vacuum field of light we improve the classical laser power stability beyond its shot noise limit by 9.4_{-0.6}^{+0.6} dB at Fourier frequencies between 5 and 80 kHz. For only 90.6 μA of detected photocurrent we achieve a relative laser power noise of 2.0_{-0.1}^{+0.1}×10^{-8}/sqrt[Hz]. This is the first demonstration of a squeezed light-enhanced laser power stabilization and its performance is equivalent to an almost tenfold increase of detected laser power in a classical scheme. The analysis reveals that the technique presented here has the potential to achieve stability levels of 4.2×10^{-10}/sqrt[Hz] with 58 mA photocurrent measured on a single photodetector.
Low-power-noise lasers are essential for many high-precision experiments. Shot noise imposes a fundamental limit on the power stability achievable with classical light sources. In this Letter, we report the generation of bright squeezed light in the audio band, which can improve the sensitivity of otherwise shot-noise-limited measurements. The bright squeezed light source is experimentally realized via the use of squeezed vacuum in a power stabilization scheme. We demonstrate a laser beam at a power of 9.9 mW with a broadband power noise suppression below the classical stabilization limit by up to 8 . 7 − 0.4 + 0.3 dB in the audio band, resulting in a bright squeezed beam with a power noise of 5 . 7 − 0.4 + 0.3 dB below shot noise for frequencies from 6 kHz to 20 kHz. We further conceptually outline a method to surpass this result in the future.
This research focuses on advanced noise suppression technologies for high-precision measurement systems, particularly addressing the limitations of classical noise reducing approaches. The noise level of laser sources is a crucial factor that directly affects the measurement sensitivity in applications such as gravitational wave detection and biomedical imaging. Classical feedback control technologies are effective but often encounter a bottleneck resulting from the classical noise suppression limits. To cope with these challenges, a novel method integrating quantum squeezed light with classical feedback control systems to reduce intensity noise is proposed in this work. By employing an amplitude-squeezed light field, a quantum-enhanced feedback control model is developed, thereby theoretically examining the influence of both the feedback loop gain and the degree of squeezing on the noise suppression performance. The results show that the injection of squeezed light significantly reduces the intensity noise, approaching the shot noise limit (SNL), thereby improving the system sensitivity beyond the classical noise reduction boundaries. Specifically, –10 dB squeezed state injection into the feedback system yields an additional noise suppression of approximately 8.97 dB, exceeding what is achievable using classical feedback alone. This demonstrates that the potential of the proposed method can enhance measurement precision close to the quantum noise limits without increasing the laser power. The analysis highlights the asymmetric noise suppression effects between the inner feedback loop and outer feedback loop. Although the outer loop benefits significantly from the squeezed light injection and achieves noise levels that are unattainable by classical feedback methods, the inner loop shows relatively minor improvements. This asymmetry is attributed to the inherent characteristics of quantum squeezing and the limitations of the feedback loop design. Further investigation into the individual noise components reveals that the primary contributors to the intensity noise include input noise, photodetector noise, and beam splitter-induced vacuum fluctuations. The injection of squeezed light effectively mitigates these vacuum fluctuations, which are typically a major noise source in high-precision laser systems. Theoretical research results show that the use of squeezed light in feedback control systems can effectively enhance noise suppression, equivalent to a nine fold increase in detected optical power, without the physical drawbacks of increasing laser power such as thermal noise. In conclusion, this study provides a theoretical validation of combining quantum squeezed states with classical feedback control to exceed classical noise suppression limits. The integration of a –10 dB squeezed state demonstrates a significant noise reduction, showing that this hybrid approach could revolutionize noise management in precision measurement applications. The results pave the way for further exploring quantum-enhanced control technologies in fields such as gravitational wave detection, quantum communication, and advanced optical sensing, providing a pathway for improving sensitivity and noise suppression without increasing additional power requirements.
Albert Einstein's General Theory of Relativity predicts the existence of ripples in space- time, the so-called gravitational waves (GWs). In the past two decades, an international array of ground-based, kilometer-scale Michelson interferometers has been set up aiming at a rst observation. These Earth-bound GW detectors target signals at audio frequen- cies in a band of ca. 10 Hz { 10 kHz. At Fourier frequencies above 1 kHz, their sensitivity is limited by quantum noise. This shot-noise arises from the zero-point uctuations of the electromagnetic eld, the so-called vacuum uctuations , which enter the interferometer through its anti-symmetric signal port. Future generations of GW observatories will even be limited by quantum noise almost over their entire detection band [ ET ]. A `classical' solution to further improve the signal-to-shot-noise ratio (SNR) of the observatories consists in an increase of the circulating light power. A higher optical load inside the interferometer will, however, lead to thermally-induced beam distortion as well as to an increased radiation pressure noise level. This will eectively result in an upper limit for the optical light power employable in future GW observatory generations. An alternative approach to improve the SNR is based on the injection of so-called squeezed states of light. Such a light eld has a characteristic non-classical noise distribution in the eld quadratures. Injected from the signal port, the squeezed state replaces the vacuum state, thereby reducing the interferometer's quantum noise. The rst part of this thesis discusses the setup of a squeezed-light laser for the German- British GW observatory GEO 600. During characterization of the device, a noise reduc- tion of up to 9.6 dB below the vacuum noise level was observed in the frequency band of 10 Hz {10 kHz, setting a new benchmark for squeezing observed at audio frequencies. Corrected for detection losses, this value furthermore corresponds to more than 11 dB of squeezing available for injection into the dark port of GEO 600. Situated on a 1 : 15 m 1 : 35 m optical breadboard, the device features transportability and can be operated independently of the GW interferometer. A key feature of the squeezed-light laser is its unprecedented long-term stability. The longest characterization measurements lasted for 20 h with an overall duty cycle of more than 99 %. In the second part of this thesis, the implementation of squeezed light into GEO 600 is presented along with the results achieved. The observatory shot noise was reduced by up to 3.4 dB, corresponding to an improvement in sensitivity by a factor of up to 1.5. For isotropically distributed GW sources, this corresponds to an increase in detection probability by 1.5 3 3.4. This makes GEO 600 the rst large-scale GW interferometer with a non-classically enhanced sensitivity. Based on the performance of the squeezed- light laser, a sensitivity improvement by a factor of two, corresponding to an equivalent optical power increase by a factor of four, seems feasible in the near future.
The optical shot-noise limit of a laser beam represents the classical limit in precision and signal to noise ratio achievable in optical sensors and imaging systems. It is known that quantum states of light, such as squeezed light and quantum correlated twin beams can be used to enhance precision and signal to noise ratio to beyond this limit. This promises optical sensors with fundamentally superior performance to the state of the art. While quantum-enhanced signal to noise ratio has been demonstrated with macroscopic powers of squeezed probe beam, demonstrations of quantum enhanced precision have remained at extremely low powers of light (femto-Watts). Here we will give examples where increasing SNR with quantum light is not sufficient to increase precision and we will review proof of principle experiments that have demonstrated sub shot noise precision, including for absorption spectroscopy and imaging. We will also report our efforts to achieve this sub-shot-noise precision performance for transmission measurement with ~0.1mW of average probe power, equating to ~10W peak power in a pulsed experiment. Time permitting, we will discuss how integrated optics and integrated electronics enables 10s GHz bandwidth in the detection of squeezed light, for integrated quantum sensor technology.
In this article, we present a novel spectroscopy technique that improves the signal-to-shot-noise ratio without the need to increase the laser power. Detrimental effects by technical noise sources are avoided by frequency-modulation techniques (frequency up-shifting). Superimposing the signal on non-classical states of light leads to a reduced quantum noise floor. Our method reveals in a proof-of-concept experiment small signals at Hz to kHz frequencies even below the shot noise limit. Our theoretical calculations fully support our experimental findings. The proposed technique is interesting for applications such as high-precision cavity spectroscopy, e.g., for explosive trace gas detection where the specific gas might set an upper limit for the laser power employed.
High-precision cavity locking is crucial for squeezing optical fields. Here, a bootstrapped low-noise photodetector is utilized in the generation process of the squeezed state of light. This process is based on a combination of a modified trans-impedance amplifier (TIA) circuit and a two-stage bootstrap amplifier circuit. This not only achieves high-precision and long-term stable locking of the optical cavity, but it also improves the degree to which the light field is squeezed. The experiment results show that the detector has a high signal-to-noise ratio (SNR) of 26.7 dB at the analysis frequency of 3 MHz when measuring the shot noise with an injection optical power of 800 µW, and the equivalent optical power noise level is lower than 2.4 pW/Hz in the frequency range of 1-30 MHz. Moreover, the squeezing degree of the quadrature amplitude squeezed state light field can be improved by more than 34.9% when the detector is used for optical cavity locking. The photodetector is useful in continuous variable (CV) quantum information research.