Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Kinetic inductance detectors for measuring the polarization of the cosmic microwave background

D. Flanigan

Published Jan 1, 2018• 1 citation
Publisher

Abstract

Kinetic inductance detectors (KIDs) are superconducting thin-film microresonators that are sensitive photon detectors. These detectors are a candidate for the next generation of experiments designed to measure the polarization of the cosmic microwave background (CMB). I discuss the basic theory needed to understand the response of a KID to light, focusing on the dynamics of the quasiparticle system. I derive an equation that describes the dynamics of the quasiparticle number, solve it in a simplified form not previously published, and show that it can describe the dynamic response of a detector. Magnetic flux vortices in a superconducting thin film can be a significant source of dissipation, and I demonstrate some techniques to prevent their formation. Based on the presented theory, I derive a corrected version of a widely-used equation for the quasiparticle recombination noise in a KID. I show that a KID consisting of a lumped-element resonator can be sensitive enough to be limited by photon noise, which is the fundamental limit for photometry, at a level of optical loading below levels in ground-based CMB experiments. Finally, I describe an ongoing project to develop multichroic KID pixels that are each sensitive to two linear polarization states in two spectral bands, intended for the next generation of CMB experiments. I show that a prototype 23-pixel array can detect millimeter-wave light, and present characterization measurements of the detectors.

DOI
10.7916/d84f336t

Related papers

Design and Performance of the Antenna-Coupled Lumped-Element Kinetic Inductance Detector

Peter S. Barry, S. Doyle, Amber L. Hornsby +6 more

Focal plane arrays consisting of low-noise, polarisation-sensitive detectors have made possible the pioneering advances in the study of the cosmic microwave background (CMB). To make further progress, the next generation of CMB experiments (e.g. CMB-S4) will require a substantial increase in the number of detectors compared to current instruments. Arrays of kinetic inductance detectors (KIDs) provide a possible path to realising such large-format arrays owing to their intrinsic multiplexing advantage and relative cryogenic simplicity. In this paper, we report on the design of a variant of the traditional KID design: the antenna-coupled lumped-element KID. A polarisation-sensitive twin-slot antenna placed behind an optimised hemispherical lens couples power onto a thin-film superconducting microstrip line. The power is then guided into the inductive section of an aluminium KID, where it is absorbed and modifies both the resonant frequency and quality factor of the KID. We present the various aspects of the design and preliminary results from the first set of seven-element prototype arrays and compare to the expected modelled performance.

arXiv:1801.06265•Journal of Low Temperature Physics•May 11, 2018•10 citations

Antenna-coupled lumped-element ALD titanium nitride KIDs for CMB instruments (Conference Presentation)

Erik D. Shirokoff, Peter S. Barry, Q. Y. Tang +1 more

Future ground-based cosmic microwave background (CMB) experiments will require more than $10^5$ polarization sensitive pixels covering multiple atmospheric bands. The scientific potential for such an experiment is impressive; however, the technical challenges are daunting: such an instrument will require square meters of focal plane covered in background limited cryogenic detectors and a dramatic increase in readout capability. We are developing novel kinetic inductance detectors (KIDs) optimized for this purpose. These devices use a twin-slot microwave antenna, superconducting Nb transmission line, and a novel coupling scheme that deposits mm-wavelength power onto a high-resistivity meander deposited as the first layer on a bare Si wafer. This architecture allows us to independently adjust the detector and antenna properties and to pursue multi-band designs. We have fabricated superconducting resonators made from atomic layer deposited (ALD) titanium nitride (TiN), with thicknesses ranging from 3 to 40 nm. We find a strong dependence of transition temperature on thickness, from 0.6 to 4.2 K for our thinnest and thickest films, respectively. In dark measurements, we find internal quality factors that range from $10^4$ to $7\times 10^5$ depending on film thickness, and kinetic inductance as high as 8 nH/square. The very small volumes and high kinetic inductance make it possible to engineer extremely sensitive detectors with inductor volumes approaching a few cubic microns that operate at readout frequencies of tens to hundreds of MHz. By taking advantage of the large fractional bandwidth available at low frequencies, we expect to achieve multiplexing densities that exceed that of state of the art TES arrays even without further improvements in film quality factor. We will present the characterization of film properties and dark devices, as well as well as initial optical results for antenna coupled single-band and single-pol devices. We will also discuss designs and sensitivity projections for future dual-pol and multi-band arrays ready for deployment in near-future CMB instruments.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jul 10, 2018•0 citations

Kinetic inductance detectors for 200μm astronomy

Simon M. Doyle, Jack Alexander Naylon, James Cox +2 more

Kinetic inductance detectors (KIDs) provide an attractive solution to the production of large detector arrays for use in ground and space based 200μm astronomy. KIDs work by measuring the change in quasi-particle density upon photon absorption in a high Q superconducting resonator. A change in quasi-particle density is measured by a shift in phase of a microwave probe signal of frequency equal to that of the resonant frequency of the KID. Such detectors have a fundamental noise limit owing to the quasi-particle recombination rate, which, in a KID fabricated from a high quality Niobium film can give sensitivities of 10-18W√Hz at 1K. Constructing KIDs of varying resonant frequencies coupled to a single transmission line provides a multiplexed detector array with simple low temperature electronics. Here we discuss the theoretical requirements for both ground and space based 200μm cameras with various radiation coupling schemes for this wavelength range using distributed and lumped element high Q resonators.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 14, 2006•4 citations

Calibration Scheme for Large Kinetic Inductance Detector Arrays Based on Readout Frequency Response

Laura Bisigello, S. J. C. Yates, Vignesh Murugesan +2 more

Microwave kinetic inductance detector (MKID) provides a way to build large ground-based sub-mm instruments such as NIKA and A-MKID. For such instruments, therefore, it is important to understand and characterize the response to ensure good linearity and calibration over a wide dynamic range. We propose to use the MKID readout frequency response to determine the MKID responsivity to an input optical source power. A signal can be measured in a KID as a change in the phase of the readout signal with respect to the KID resonant circle. Fundamentally, this phase change is due to a shift in the KID resonance frequency, in turn due to a radiation induced change in the quasiparticle number in the superconducting resonator. We show that the shift in resonant frequency can be determined from the phase shift by using KID phase versus frequency dependence using a previously measured resonant frequency. Working in this calculated resonant frequency, we gain near linearity and constant calibration to a constant optical signal applied in a wide range of operating points on the resonance and readout powers. This calibration method has three particular advantages: first, it is fast enough to be used to calibrate large arrays, with pixel counts in the thousands of pixels; second, it is based on data that are already necessary to determine KID positions; third, it can be done without applying any optical source in front of the array.

arXiv:1602.00442•Journal of Low Temperature Physics•Feb 9, 2016•13 citations

Inter-Site Fluctuation Mechanics and Quasiparticle Generation-Recombination Noise in Kinetic Inductance Detectors (KID)

James Glenn-Anderson

Kinetic Inductance Detectors (KIDs) represent a cornerstone of modern millimeter-wave, sub-millimeter, and far-infrared astronomical instrumentation, offering unmatched multiplexing capabilities for large-format focal planes in cosmic microwave background (CMB) polarimetry and spectroscopic survey telescopes. Operating at deep cryogenic temperatures () via the modulation of superconducting surface impedance under photon-induced pair breaking [11], KIDs rely on the kinetic inductance effect to translate Cooper-pair density variations into resonant frequency and phase shifts. However, their ultimate sensitivity is frequently limited by excess low-frequency phase and amplitude noise that traditional quasiparticle generation-recombination (G-R) and Two-Level System (TLS) surface defect models fail to fully resolve. In this work, we extend our first-principles inter-site fluctuation mechanics —previously established for Transition-Edge Sensors (TES) and cryogenic field-effect transistors—to the dissipative electrodynamic transport regime of superconducting microresonators. We present a rigorous field-theoretic derivation of the inter-site fluctuation matrix governing amorphous dielectric-superconductor interfaces and grain boundaries in high-Q superconducting microstrip and coplanar waveguide (CPW) geometries. By decoupling classical thermal activation from quantum zero-point phase dispersion, we formulate a unified stochastic master equation that couples quantum inter-site tunneling, superconductive order-parameter phase dynamics, and non-equilibrium quasiparticle generation-recombination kinetics. We derive the exact non-stationary relaxation time distribution and the resulting resonant frequency noise spectral density, and integrate this framework into a modified Mattis-Bardeen surface impedance and phase readout formulation. Finally, we outline a high-performance MATLAB simulation architecture designed to validate the tripartite noise hierarchy across cryogenic operational regimes, providing instrument designers with an uncompromising theoretical foundation for next-generation focal-plane optimization.

•Nov 7, 2026•0 citations

Nonequilibrium behaviour and quasiparticle heating in thin film superconducting microwave resonators

Tejas Guruswamy

In this thesis I describe work on developing theoretical and numerical models of supercon- ducting thin-film microwave resonators. Superconducting resonators are used in a variety of applications, one of which is as kinetic inductance detectors (KIDs). KIDs are ultra-low noise, highly sensitive, multiplexable detectors, with uses in a wide variety of fields including astrophysics, medical imaging, and particle physics. Resonators are also crucial for supercon- ducting qubit readout, superconducting mixers and parametric amplifiers, and as multiplexers for other devices. The results described in this thesis apply to all thin film resonators, but are primarily described in the context of KIDs. I develop models of how constant absorbed power affects superconducting thin films, driving them out of thermal equilibrium with the bath. Using the Chang & Scalapino equations, I calculate numerically the steady-state quasiparticle and phonon distributions for various sources of power (sub-gap and above-gap photons and phonons, single frequency and broadband). Many new results emerge, a few of which are: the quasiparticle heating effects of microwave power, explaining the experimentally measured saturation of resonator performance; the frequency dependence of the quasiparticle generation efficiency in the sub-mm wavelength range; and the importance of phonon trapping in thin films at low temperatures. I then use these nonequilibrium results in higher-level device models. Starting from a generic framework for resonators, I present and implement a model of a KID with variable thermal isolation. I calculate the effects of quasiparticle heating on both the large-signal and small-signal behaviour, highlighting the effects of electrothermal feedback caused by readout power. Electrothermal feedback is shown to be able to increase or decrease the magnitude and bandwidth of the responsivity and noise, depending on the operating point. Finally, I propose an experimental measurement of quasiparticle heating effects in a new device – a four-port ring resonator. In such a device, unlike in the standard two-port resonator, the device can be heated and read out independently. I develop detailed models for the thermal and electrical behaviour of these devices, and suggest a scheme by which the quasiparticle heating effects of microwave power, predicted in this thesis, can be measured.

•Dec 20, 2017•8 citations
Kinetic inductance detectors (KIDs) are superconducting thin-film microresonators that are sensitive photon detectors. These detectors are a candidate for the next generation of experiments designed to measure the polarization of the cosmic microwave background (CMB). I discuss the basic theory needed to understand the response of a KID to light, focusing on the dynamics of the quasiparticle system. I derive an equation that describes the dynamics of the quasiparticle number, solve it in a simplified form not previously published, and show that it can describe the dynamic response of a detector. Magnetic flux vortices in a superconducting thin film can be a significant source of dissipation, and I demonstrate some techniques to prevent their formation. Based on the presented theory, I derive a corrected version of a widely-used equation for the quasiparticle recombination noise in a KID. I show that a KID consisting of a lumped-element resonator can be sensitive enough to be limited by photon noise, which is the fundamental limit for photometry, at a level of optical loading below levels in ground-based CMB experiments. Finally, I describe an ongoing project to develop multichroic KID pixels that are each sensitive to two linear polarization states in two spectral bands, intended for the next generation of CMB experiments. I show that a prototype 23-pixel array can detect millimeter-wave light, and present characterization measurements of the detectors.
Focal plane arrays consisting of low-noise, polarisation-sensitive detectors have made possible the pioneering advances in the study of the cosmic microwave background (CMB). To make further progress, the next generation of CMB experiments (e.g. CMB-S4) will require a substantial increase in the number of detectors compared to current instruments. Arrays of kinetic inductance detectors (KIDs) provide a possible path to realising such large-format arrays owing to their intrinsic multiplexing advantage and relative cryogenic simplicity. In this paper, we report on the design of a variant of the traditional KID design: the antenna-coupled lumped-element KID. A polarisation-sensitive twin-slot antenna placed behind an optimised hemispherical lens couples power onto a thin-film superconducting microstrip line. The power is then guided into the inductive section of an aluminium KID, where it is absorbed and modifies both the resonant frequency and quality factor of the KID. We present the various aspects of the design and preliminary results from the first set of seven-element prototype arrays and compare to the expected modelled performance.
Future ground-based cosmic microwave background (CMB) experiments will require more than 10510^5105 polarization sensitive pixels covering multiple atmospheric bands. The scientific potential for such an experiment is impressive; however, the technical challenges are daunting: such an instrument will require square meters of focal plane covered in background limited cryogenic detectors and a dramatic increase in readout capability. We are developing novel kinetic inductance detectors (KIDs) optimized for this purpose. These devices use a twin-slot microwave antenna, superconducting Nb transmission line, and a novel coupling scheme that deposits mm-wavelength power onto a high-resistivity meander deposited as the first layer on a bare Si wafer. This architecture allows us to independently adjust the detector and antenna properties and to pursue multi-band designs. We have fabricated superconducting resonators made from atomic layer deposited (ALD) titanium nitride (TiN), with thicknesses ranging from 3 to 40 nm. We find a strong dependence of transition temperature on thickness, from 0.6 to 4.2 K for our thinnest and thickest films, respectively. In dark measurements, we find internal quality factors that range from 10410^4104 to 7×1057\times 10^57×105 depending on film thickness, and kinetic inductance as high as 8 nH/square. The very small volumes and high kinetic inductance make it possible to engineer extremely sensitive detectors with inductor volumes approaching a few cubic microns that operate at readout frequencies of tens to hundreds of MHz. By taking advantage of the large fractional bandwidth available at low frequencies, we expect to achieve multiplexing densities that exceed that of state of the art TES arrays even without further improvements in film quality factor. We will present the characterization of film properties and dark devices, as well as well as initial optical results for antenna coupled single-band and single-pol devices. We will also discuss designs and sensitivity projections for future dual-pol and multi-band arrays ready for deployment in near-future CMB instruments.
Kinetic inductance detectors (KIDs) provide an attractive solution to the production of large detector arrays for use in ground and space based 200μm astronomy. KIDs work by measuring the change in quasi-particle density upon photon absorption in a high Q superconducting resonator. A change in quasi-particle density is measured by a shift in phase of a microwave probe signal of frequency equal to that of the resonant frequency of the KID. Such detectors have a fundamental noise limit owing to the quasi-particle recombination rate, which, in a KID fabricated from a high quality Niobium film can give sensitivities of 10-18W√Hz at 1K. Constructing KIDs of varying resonant frequencies coupled to a single transmission line provides a multiplexed detector array with simple low temperature electronics. Here we discuss the theoretical requirements for both ground and space based 200μm cameras with various radiation coupling schemes for this wavelength range using distributed and lumped element high Q resonators.
Microwave kinetic inductance detector (MKID) provides a way to build large ground-based sub-mm instruments such as NIKA and A-MKID. For such instruments, therefore, it is important to understand and characterize the response to ensure good linearity and calibration over a wide dynamic range. We propose to use the MKID readout frequency response to determine the MKID responsivity to an input optical source power. A signal can be measured in a KID as a change in the phase of the readout signal with respect to the KID resonant circle. Fundamentally, this phase change is due to a shift in the KID resonance frequency, in turn due to a radiation induced change in the quasiparticle number in the superconducting resonator. We show that the shift in resonant frequency can be determined from the phase shift by using KID phase versus frequency dependence using a previously measured resonant frequency. Working in this calculated resonant frequency, we gain near linearity and constant calibration to a constant optical signal applied in a wide range of operating points on the resonance and readout powers. This calibration method has three particular advantages: first, it is fast enough to be used to calibrate large arrays, with pixel counts in the thousands of pixels; second, it is based on data that are already necessary to determine KID positions; third, it can be done without applying any optical source in front of the array.
Kinetic Inductance Detectors (KIDs) represent a cornerstone of modern millimeter-wave, sub-millimeter, and far-infrared astronomical instrumentation, offering unmatched multiplexing capabilities for large-format focal planes in cosmic microwave background (CMB) polarimetry and spectroscopic survey telescopes. Operating at deep cryogenic temperatures () via the modulation of superconducting surface impedance under photon-induced pair breaking [11], KIDs rely on the kinetic inductance effect to translate Cooper-pair density variations into resonant frequency and phase shifts. However, their ultimate sensitivity is frequently limited by excess low-frequency phase and amplitude noise that traditional quasiparticle generation-recombination (G-R) and Two-Level System (TLS) surface defect models fail to fully resolve. In this work, we extend our first-principles inter-site fluctuation mechanics —previously established for Transition-Edge Sensors (TES) and cryogenic field-effect transistors—to the dissipative electrodynamic transport regime of superconducting microresonators. We present a rigorous field-theoretic derivation of the inter-site fluctuation matrix governing amorphous dielectric-superconductor interfaces and grain boundaries in high-Q superconducting microstrip and coplanar waveguide (CPW) geometries. By decoupling classical thermal activation from quantum zero-point phase dispersion, we formulate a unified stochastic master equation that couples quantum inter-site tunneling, superconductive order-parameter phase dynamics, and non-equilibrium quasiparticle generation-recombination kinetics. We derive the exact non-stationary relaxation time distribution and the resulting resonant frequency noise spectral density, and integrate this framework into a modified Mattis-Bardeen surface impedance and phase readout formulation. Finally, we outline a high-performance MATLAB simulation architecture designed to validate the tripartite noise hierarchy across cryogenic operational regimes, providing instrument designers with an uncompromising theoretical foundation for next-generation focal-plane optimization.
In this thesis I describe work on developing theoretical and numerical models of supercon- ducting thin-film microwave resonators. Superconducting resonators are used in a variety of applications, one of which is as kinetic inductance detectors (KIDs). KIDs are ultra-low noise, highly sensitive, multiplexable detectors, with uses in a wide variety of fields including astrophysics, medical imaging, and particle physics. Resonators are also crucial for supercon- ducting qubit readout, superconducting mixers and parametric amplifiers, and as multiplexers for other devices. The results described in this thesis apply to all thin film resonators, but are primarily described in the context of KIDs. I develop models of how constant absorbed power affects superconducting thin films, driving them out of thermal equilibrium with the bath. Using the Chang & Scalapino equations, I calculate numerically the steady-state quasiparticle and phonon distributions for various sources of power (sub-gap and above-gap photons and phonons, single frequency and broadband). Many new results emerge, a few of which are: the quasiparticle heating effects of microwave power, explaining the experimentally measured saturation of resonator performance; the frequency dependence of the quasiparticle generation efficiency in the sub-mm wavelength range; and the importance of phonon trapping in thin films at low temperatures. I then use these nonequilibrium results in higher-level device models. Starting from a generic framework for resonators, I present and implement a model of a KID with variable thermal isolation. I calculate the effects of quasiparticle heating on both the large-signal and small-signal behaviour, highlighting the effects of electrothermal feedback caused by readout power. Electrothermal feedback is shown to be able to increase or decrease the magnitude and bandwidth of the responsivity and noise, depending on the operating point. Finally, I propose an experimental measurement of quasiparticle heating effects in a new device – a four-port ring resonator. In such a device, unlike in the standard two-port resonator, the device can be heated and read out independently. I develop detailed models for the thermal and electrical behaviour of these devices, and suggest a scheme by which the quasiparticle heating effects of microwave power, predicted in this thesis, can be measured.