Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Gain bandwidth of NbN HEB mixers on GaN buffer layer operating at 2 THz local oscillator frequency

Sergey V. Antipov, Andrey Trifonov, Sascha Krause, Denis Meledin, Vincent Desmaris, Victor Y. Belitsky, Gregory N Gol'tsman

Published Jan 1, 2017• 0 citations
OpenAlex

Abstract

In this paper, we present IF bandwidth measurement results of NbN HEB mixers, which are employing NbN thin films grown on a GaN buffer-layer. The HEB mixers were operated in the heterodyne regime at a bath temperature of approximately 4.5 K and with a local oscillator operating at a frequency of 2 THz. A quantum cascade laser served as the local oscillator and a reference synthesizer based on a BWO generator (130-160 GHz) and a semiconductor superlattice (SSL) frequency multiplier was used as a signal source. By changing the LO frequency it was possible to record the IF response or gain bandwidth of the HEB with a spectrum analyzer at the operation point, which yielded lowest noise temperature. The gain bandwidth that was recorded in the heterodyne regime at 2 THz amounts to approximately 5 GHz and coincides well with a measurement that has been performed at elevated bath temperatures and lower LO frequency of 140 GHz. These findings strongly support that by using a GaN buffer-layer the phonon escape time of NbN HEBs can be significantly lower as compared to e.g. Si substrate, thus, providing higher gain bandwidth.

Related papers

GAIN BANDWIDTH OF PHONON-COOLED HEB MIXER MADE OF NBN THIN FILM WITH MgO BUFFER LAYER ON Si.

Yu. B. Vachtomin, Matvey I. Finkel, Sergey V. Antipov +5 more

We present recently obtained values for gain bandwidth of NbN HEB mixers for different substrates and film thicknesses and for MgO buffer layer on Si at LO frequency of 0.85-1 THz. The maximal bandwidth, 5.2 GHz, was achieved for the device on MgO buffer layer on Si with a 2 nm thick NbN film. Functional devices based on NbN films of such thickness were fabricated for the first time due to an improvement of superconducting properties of NbN film deposited on MgO buffer layer on Si substrate. Introduction. In the last years, the development of HEB mixers has reached such a high level that these devices can be successfully utilized in heterodyne receivers of THz frequency range. Their high sensitivity and low LO power make them suitable for radioastronomic observations on space- and airbom platforms. An NbN HEB mixer seems to be a

•Mar 1, 2002•11 citations

Noise performance of a balanced waveguide NbN HEB mixer utilizing a GaN buffer-layer at 1.3 THz

Sascha Krause, Denis Meledin, Vincent Desmaris +2 more

We report on the initial measurement results of a balanced waveguide phonon cooled NbN mixer employing a 5.5 µm thin GaN membrane, which was operated at frequencies around 1.3 THz. The uncorrected DSB noise temperature amounts to approximately 750 K at 1 GHz IF and increases to only 900 K at 4 GHz IF, which was deduced from the standard Y-factor measurement technique. The recorded IF spectrum from 0.5 GHz to 8 GHz suggests a measured noise bandwidth of approximately 7 GHz owing to the employment of a GaN buffer-layer, which promotes the single crystal growth of NbN films and provides high phonon transparency, thus lowering the phonon escape time. We emphasize with the implementation of a waveguide balanced receiver scheme and using NbN/GaN mixers the possibility to extend the operational IF range of phonon cooled NbN HEBs, yet providing low noise performance.

•Jan 1, 2018•1 citation

Study of IF bandwidth of NbN hot electron bolometers on GaN buffer layer using a direct measurement method

Sascha Krause, Vladislav Mityashkin, Sergey V. Antipov +5 more

In this paper, we present a reliable measurement method to study the influence of the GaN buffer layer on phonon-escape time in comparison with commonly used Si substrates and, in consequence, on the IF bandwidth of HEBs. One of the key aspects is to operate the HEB mixer at elevated bath temperatures close to the critical temperature of the NbN ultra-thin film, where contributions from electron-phonon processes and self-heating effects are relatively small, therefore IF roll-off will be governed by the phonon-escape.Two independent experiments were performed at GARD and MSPU on a similar experimental setup at frequencies of approximately 180 and 140 GHz, respectively, and have shown reproducible and consistent results. The entire IF chain was characterized by S-parameter measurements. We compared the measurement results of epitaxial NbN grown onto GaN buffer-layer with Tc of 12.5 K (4.5 nm) with high quality polycrystalline NbN films on Si substrate with Tc of 10.5 K (5 nm) and observed a strong indication of an enhancement of phonon escape to the substrate by a factor of two for the NbN/GaN material combination.

•Jan 1, 2016•0 citations

NbN phonon-cooled hot-electron bolometer mixer for terahertz heterodyne receivers

Gregory N Gol'tsman, Yu. B. Vachtomin, Sergey V. Antipov +8 more

We present the results of our studies of NbN phonon-cooled HEB mixers at terahertz frequencies. The mixers were fabricated from NbN film deposited on a high-resistivity Si substrate with an MgO buffer layer. The mixer element was integrated with a log-periodic spiral antenna. The noise temperature measurements were performed at 2.5 THz and at 3.8 THz local oscillator frequencies for the 3 x 0.2 μm2 active area devices. The best uncorrected receiver noise temperatures found for these frequencies are 1300 K and 3100 K, respectively. A water vapour discharge laser was used as the LO source. The largest gain bandwidth of 5.2 GHz was achieved for a mixer based on 2 nm thick NbN film deposited on MgO layer over Si substrate. The gain bandwidth of the mixer based on 3.5 nm NbN film deposited on Si with MgO is 4.2 GHz and the noise bandwidth for the same device amounts to 5 GHz. We also present the results of our research into decrease of the direct detection contribution to the measured Y-factor and a possible error of noise temperature calculation. The use of a square nickel cell mesh as an IR-filter enabled us to avoid the effect of direct detection and measure apparent value of the noise temperature which was 16% less than that obtained using conventional black polyethylene IR-filter.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Mar 25, 2005•12 citations

Design of a wideband balanced waveguide HEB mixer employing a GaN buffer-layer for the 1-1.5 THz band

Sascha Krause, Denis Meledin, Vincent Desmaris +1 more

We present the design and implementation of a wideband balanced waveguide NbN HEB mixer employing a GaN substrate in the frequency range of 1 - 1.5 THz.The balanced receiver scheme consisting of a 90˚ RF hybrid, a pair of NbN phonon-cooled HEB mixers and a 180˚ IF hybrid has major advantages over the single-ended configuration. The 3 dB RF hybrid is employed to couple the RF and LO signal into the HEBs, and allows for the efficient use of available LO power. Furthermore, the usually small IF bandwidth of phonon-cooled NbN HEB mixers has been addressed by employing a GaN substrate instead of a conventional substrate, e.g., Si or quartz. It has recently been shown that using GaN substrate reduces the escape time of phonons from NbN bridge to the substrate and thus, prospectively enhances the overall cooling rate of hot electrons and yielding higher IF bandwidth. The mixer housing is implemented in a back-end configuration and has been fabricated by means of a micro-machining method, providing excellent control of the dimensions and smoothness of the all-metal waveguide components. The expected RF performance of the proposed HEB design as well as its fabrication and DC characterization are presented

•Jan 1, 2017•1 citation

Comparative Study of the Bandwidth of Phonon-Cooled NbN Hot-Electron Bolometers in Submillimeter and Optical Wavelength Ranges

K. Ilin, Serguei Cherednichenko, Gregory N Gol'tsman +2 more

We report the results of the bandwidth measurements of NbN hot-electron bolometers, perfomied in the terahertz frequency domain at 140 GHz and 660 GHz and in time domain in the optical range at the wavelength of 395 nm.. Our studies were done on 3.5-nm-thick NbN films evaporated on sapphire substrates and patterned into ilin-size microbridges. In order to measure the gain bandwidth, we used two identical BWOs (140 or 660 GHz), one functioning as a local oscillator and the other as a signal source. The bandwidth we achieved was 3.5-4 GHz at 4.2 K with the optimal LO and DC biases. Time-domain measurements with a resolution below 300 fs were performed using an electro-optic sampling system, in the temperature range between 4.2 K to 9 K at various values of the bias current and optical power. The obtained response time of the NbN hot-electron bolometer to —100fs-wide Ti:sapphire laser pulses was about 27 ps, what corresponds to the 5.9 GHz gain bandwidth. Introduction The bandwidth of hot-electron bolometer (HEB) mixers has reached values which are record for bolometers. The gain bandwidth for phonon-cooled NbN HEB mixers of 4 GHz for 140 GHz and 650 GHz frequencies [1, 2] and the noise bandwidth of 8 GHz for 650 GHz [2] have been demonstrated. For diffusion-cooled Nb HEB mixers, the bandwidth has reached 6 GHz, when measured at 20--40 GHz [3]. However, there is a definite practical interest to even further extend the bandwidth of these devices. The possibilities of the HEB mixer technology in this direction are far from being exhausted. For example, the future of the NbN HEB technology requires that critical temperature Tc > 10 K and critical current density j c > 10 6 Akm at 4.2 K are simultaneously obtained for d < 3 nm-thick films M. The reduction of the optimal power of the local oscillator PLID below 100 nW leads to the decrease of the device length down to L < 0.2 pm, which, in turn, should bring an additional cooling channel for hot electrons—diffusion into metal contacts and a further bandwidth extension.

Softwaretechnik-Trends•Mar 1, 1998•0 citations
In this paper, we present IF bandwidth measurement results of NbN HEB mixers, which are employing NbN thin films grown on a GaN buffer-layer. The HEB mixers were operated in the heterodyne regime at a bath temperature of approximately 4.5 K and with a local oscillator operating at a frequency of 2 THz. A quantum cascade laser served as the local oscillator and a reference synthesizer based on a BWO generator (130-160 GHz) and a semiconductor superlattice (SSL) frequency multiplier was used as a signal source. By changing the LO frequency it was possible to record the IF response or gain bandwidth of the HEB with a spectrum analyzer at the operation point, which yielded lowest noise temperature. The gain bandwidth that was recorded in the heterodyne regime at 2 THz amounts to approximately 5 GHz and coincides well with a measurement that has been performed at elevated bath temperatures and lower LO frequency of 140 GHz. These findings strongly support that by using a GaN buffer-layer the phonon escape time of NbN HEBs can be significantly lower as compared to e.g. Si substrate, thus, providing higher gain bandwidth.
We present recently obtained values for gain bandwidth of NbN HEB mixers for different substrates and film thicknesses and for MgO buffer layer on Si at LO frequency of 0.85-1 THz. The maximal bandwidth, 5.2 GHz, was achieved for the device on MgO buffer layer on Si with a 2 nm thick NbN film. Functional devices based on NbN films of such thickness were fabricated for the first time due to an improvement of superconducting properties of NbN film deposited on MgO buffer layer on Si substrate. Introduction. In the last years, the development of HEB mixers has reached such a high level that these devices can be successfully utilized in heterodyne receivers of THz frequency range. Their high sensitivity and low LO power make them suitable for radioastronomic observations on space- and airbom platforms. An NbN HEB mixer seems to be a
We report on the initial measurement results of a balanced waveguide phonon cooled NbN mixer employing a 5.5 µm thin GaN membrane, which was operated at frequencies around 1.3 THz. The uncorrected DSB noise temperature amounts to approximately 750 K at 1 GHz IF and increases to only 900 K at 4 GHz IF, which was deduced from the standard Y-factor measurement technique. The recorded IF spectrum from 0.5 GHz to 8 GHz suggests a measured noise bandwidth of approximately 7 GHz owing to the employment of a GaN buffer-layer, which promotes the single crystal growth of NbN films and provides high phonon transparency, thus lowering the phonon escape time. We emphasize with the implementation of a waveguide balanced receiver scheme and using NbN/GaN mixers the possibility to extend the operational IF range of phonon cooled NbN HEBs, yet providing low noise performance.
In this paper, we present a reliable measurement method to study the influence of the GaN buffer layer on phonon-escape time in comparison with commonly used Si substrates and, in consequence, on the IF bandwidth of HEBs. One of the key aspects is to operate the HEB mixer at elevated bath temperatures close to the critical temperature of the NbN ultra-thin film, where contributions from electron-phonon processes and self-heating effects are relatively small, therefore IF roll-off will be governed by the phonon-escape.Two independent experiments were performed at GARD and MSPU on a similar experimental setup at frequencies of approximately 180 and 140 GHz, respectively, and have shown reproducible and consistent results. The entire IF chain was characterized by S-parameter measurements. We compared the measurement results of epitaxial NbN grown onto GaN buffer-layer with Tc of 12.5 K (4.5 nm) with high quality polycrystalline NbN films on Si substrate with Tc of 10.5 K (5 nm) and observed a strong indication of an enhancement of phonon escape to the substrate by a factor of two for the NbN/GaN material combination.
We present the results of our studies of NbN phonon-cooled HEB mixers at terahertz frequencies. The mixers were fabricated from NbN film deposited on a high-resistivity Si substrate with an MgO buffer layer. The mixer element was integrated with a log-periodic spiral antenna. The noise temperature measurements were performed at 2.5 THz and at 3.8 THz local oscillator frequencies for the 3 x 0.2 μm2 active area devices. The best uncorrected receiver noise temperatures found for these frequencies are 1300 K and 3100 K, respectively. A water vapour discharge laser was used as the LO source. The largest gain bandwidth of 5.2 GHz was achieved for a mixer based on 2 nm thick NbN film deposited on MgO layer over Si substrate. The gain bandwidth of the mixer based on 3.5 nm NbN film deposited on Si with MgO is 4.2 GHz and the noise bandwidth for the same device amounts to 5 GHz. We also present the results of our research into decrease of the direct detection contribution to the measured Y-factor and a possible error of noise temperature calculation. The use of a square nickel cell mesh as an IR-filter enabled us to avoid the effect of direct detection and measure apparent value of the noise temperature which was 16% less than that obtained using conventional black polyethylene IR-filter.
We present the design and implementation of a wideband balanced waveguide NbN HEB mixer employing a GaN substrate in the frequency range of 1 - 1.5 THz.The balanced receiver scheme consisting of a 90˚ RF hybrid, a pair of NbN phonon-cooled HEB mixers and a 180˚ IF hybrid has major advantages over the single-ended configuration. The 3 dB RF hybrid is employed to couple the RF and LO signal into the HEBs, and allows for the efficient use of available LO power. Furthermore, the usually small IF bandwidth of phonon-cooled NbN HEB mixers has been addressed by employing a GaN substrate instead of a conventional substrate, e.g., Si or quartz. It has recently been shown that using GaN substrate reduces the escape time of phonons from NbN bridge to the substrate and thus, prospectively enhances the overall cooling rate of hot electrons and yielding higher IF bandwidth. The mixer housing is implemented in a back-end configuration and has been fabricated by means of a micro-machining method, providing excellent control of the dimensions and smoothness of the all-metal waveguide components. The expected RF performance of the proposed HEB design as well as its fabrication and DC characterization are presented
We report the results of the bandwidth measurements of NbN hot-electron bolometers, perfomied in the terahertz frequency domain at 140 GHz and 660 GHz and in time domain in the optical range at the wavelength of 395 nm.. Our studies were done on 3.5-nm-thick NbN films evaporated on sapphire substrates and patterned into ilin-size microbridges. In order to measure the gain bandwidth, we used two identical BWOs (140 or 660 GHz), one functioning as a local oscillator and the other as a signal source. The bandwidth we achieved was 3.5-4 GHz at 4.2 K with the optimal LO and DC biases. Time-domain measurements with a resolution below 300 fs were performed using an electro-optic sampling system, in the temperature range between 4.2 K to 9 K at various values of the bias current and optical power. The obtained response time of the NbN hot-electron bolometer to —100fs-wide Ti:sapphire laser pulses was about 27 ps, what corresponds to the 5.9 GHz gain bandwidth. Introduction The bandwidth of hot-electron bolometer (HEB) mixers has reached values which are record for bolometers. The gain bandwidth for phonon-cooled NbN HEB mixers of 4 GHz for 140 GHz and 650 GHz frequencies [1, 2] and the noise bandwidth of 8 GHz for 650 GHz [2] have been demonstrated. For diffusion-cooled Nb HEB mixers, the bandwidth has reached 6 GHz, when measured at 20--40 GHz [3]. However, there is a definite practical interest to even further extend the bandwidth of these devices. The possibilities of the HEB mixer technology in this direction are far from being exhausted. For example, the future of the NbN HEB technology requires that critical temperature Tc > 10 K and critical current density j c > 10 6 Akm at 4.2 K are simultaneously obtained for d < 3 nm-thick films M. The reduction of the optimal power of the local oscillator PLID below 100 nW leads to the decrease of the device length down to L < 0.2 pm, which, in turn, should bring an additional cooling channel for hot electrons—diffusion into metal contacts and a further bandwidth extension.