Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)

Mixer gain calculations of a SIS waveguide mixer using an integrated tuning structure

Karl Jacobs

Published Oct 1, 1991• 1 citation
Publisher

Abstract

RF coupling to Superconductor-Isolator-Superconductor (SIS) junctions suffers from their large geometric capacitance (45 to 60 fF/μm 2 for Nb-Al 2 O 3 -Nb junctions). Junction areas smaller than 1 μm 2 would be necessary for submillimeter wavelengths but pose considerable difficulties in fabrication. We show mixer performance calculations for moderately sized junctions using an integrated open circuited microstrip stub to tune out the junction capacitance.

DOI
10.1117/12.2297783

Related papers

Performance of a 230 GHz SIS receiver using broadband integrated matching structures

Karl Jacobs

For low noise performance of SIS junctions as heterodyne mixing elements a common requirement is an coRC of the junction of around 3-4. For R=505), co=27t•230 GHz, and a specific capacitance of 60 fF/µ,m2, this means a junction area of 0.69 ptm2, i.e. submicron area junctions. Junctions of these dimensions are difficult to fabricate. Using arrays of junctions to reduce the effective capacitance results in the necessity of high current densities and requires good junction uniformity. Using an integrated superconducting impedance matching structure, we were able to get good performance at 230 GHz with single junctions as large as 2.5 IA m2 (Nb-A10x-Nb junctions fabricated at KOSMA, University of Cologne). An additional advantage of the large size is the low magnetic field necessary to suppress the Josephson currents. The matching structure is described in a companion paper [1]. It consists of a loaded stub compensating for the junction capacitance and two ',za /4 transformer sections which transform the real part of the resulting impedance. The waveguide mixer uses a backshort and an E-plane tuner in full height waveguide and was optimized together with the RF filter by scale modeling to give a maximum impedance tuning range [2]. A sketch of the test receiver is shown in Fig. 1. The IF HEMT amplifier has a noise temperature of 8K and was developed in house.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Dec 7, 2017•2 citations

Two-junction tuning circuits for submillimeter SIS mixers

Jonas Stasys Zmuidzinas, Henry George LeDuc, J. A. Stern +1 more

The capacitance of superconducting tunnel junctions can seriously degrade the performance of quasiparticle (SIS) mixers operating in the submillimeter band, so it is essential to provide a circuit for tuning out this capacitance at the operating frequency. In this article, we present two new tuning circuits for SIS mixers which use a pair of SIS junctions connected by an inductance. Compared to previously proposed tuning circuits, ours have a broader bandwidth, are easier to scale to higher frequencies, and may be easier to fabricate. We have constructed quasi-optical mixers which employ these tuning circuits, using Nb/Al-Oxide/Nb SIS junctions defined by optical lithography. The performance of these devices is excellent, giving receiver noise temperatures of 113 K (DSB) at 490 GHz and 230 K DSB at 612 GHz. In addition to demonstrating the effectiveness of our tuning circuit, these results show that quasi-optical mixers can be competitive with or superior to waveguide mixers at submillimeter wavelengths. The mixers continue to perform well at frequencies up to 672 GHz, which is about 95% of the Nb gap frequency.>

IEEE Transactions on Microwave Theory and Techniques•Apr 1, 1994•126 citations

MM wave quasioptical SIS mixers

Qing Hu, C. A. Mears, P. L. Richards +1 more

The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>

IEEE Transactions on Magnetics•Mar 1, 1989•32 citations

A Simple Integrated Matching Element for SIS Quasiparticle Mixers

Antti V. Räisänen, William R. McGrath, P. L. Richards +1 more

An integrated superconducting microstrip is shown to be a convenient, flexible, and well characterized matching element for a superconductor-insulator-superconductor (SIS) heterodyne mixer. An open-circuited microstrip stub that reflects a parallel inductance across the junction is used to broaden the bandwidth of the RF match of a 30-40 GHz SIS mixer. Measurements with Pb-alloy junctions in a full-height waveguide mixer with fixed mechanical tuning give an instantaneous bandwidth of 10 to 15 percent with a mixer noise temperature T/sub M/(DSB)=10+-2.5 K.

IEEE MTT-S International Microwave Symposium digest•Mar 23, 2005•0 citations

Characterization of Nb-based superconducting microstrip lines around the gap frequency

Sheng-Cai Shi, Chi-Chung Chin, Wen Zhang

Submillimeter-wave SIS mixers usually adopt junctions associated with an integrated tuning circuit, which tunes out the junction's capacitance and is typically a thin-film superconducting microstrip line. This paper mainly investigates the characteristic of Nb-based superconducting microstrip lines around the junction's gap frequency and its effect on the performance of SIS mixers.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Nov 7, 2002•2 citations

Performance of NbN superconductive tunnel junctions as SIS mixers at 205 GHz

William R. McGrath, J. A. Stern, Hamid Javadi +3 more

Small area (<or=1- mu m/sup 2/), high-current-density NbN-MgO-NbN tunnel junctions with I-V characteristics suitable for high-frequency mixers have been fabricated. Mesa-geometry junctions with an area of about 1 mu m/sup 2/ and critical current density of 5-10 kA/cm/sup 2/ are integrated with superconducting microstrip lines designed to resonate out the junction capacitance. Accurate values of junction capacitance and magnetic penetration depth are required for the proper design of the microstrip. A study was made of the mixer gain and noise performance near 205 GHz as a function of the inductance provided by the microstrip line. This has confirmed, at a high millimeter-wave frequency, values of junction capacitance of 85 fF/ mu m/sup 2/ and recently measured values of a magnetic penetration depth of 380 nm. Mixer noise temperatures as low as 134 K at 1.5 K have been obtained for properly tuned junctions. A significant improvement in mixer performance on cooling from 4.2 K to 1.5 K was observed. Edge-geometry junctions with an area of 0.3 mu m/sup 3/ and critical current density of 18-25 kA/cm/sup 2/ have also been fabricated. These junctions give a mixer noise temperature of 145 K at 4.2 K without the use of integrated tuning elements. These are the best results ever achieved for NbN-based SIS mixers.

IEEE Transactions on Magnetics•Mar 1, 1991•27 citations
RF coupling to Superconductor-Isolator-Superconductor (SIS) junctions suffers from their large geometric capacitance (45 to 60 fF/μm 2 for Nb-Al 2 O 3 -Nb junctions). Junction areas smaller than 1 μm 2 would be necessary for submillimeter wavelengths but pose considerable difficulties in fabrication. We show mixer performance calculations for moderately sized junctions using an integrated open circuited microstrip stub to tune out the junction capacitance.
For low noise performance of SIS junctions as heterodyne mixing elements a common requirement is an coRC of the junction of around 3-4. For R=505), co=27t•230 GHz, and a specific capacitance of 60 fF/µ,m2, this means a junction area of 0.69 ptm2, i.e. submicron area junctions. Junctions of these dimensions are difficult to fabricate. Using arrays of junctions to reduce the effective capacitance results in the necessity of high current densities and requires good junction uniformity. Using an integrated superconducting impedance matching structure, we were able to get good performance at 230 GHz with single junctions as large as 2.5 IA m2 (Nb-A10x-Nb junctions fabricated at KOSMA, University of Cologne). An additional advantage of the large size is the low magnetic field necessary to suppress the Josephson currents. The matching structure is described in a companion paper [1]. It consists of a loaded stub compensating for the junction capacitance and two ',za /4 transformer sections which transform the real part of the resulting impedance. The waveguide mixer uses a backshort and an E-plane tuner in full height waveguide and was optimized together with the RF filter by scale modeling to give a maximum impedance tuning range [2]. A sketch of the test receiver is shown in Fig. 1. The IF HEMT amplifier has a noise temperature of 8K and was developed in house.
The capacitance of superconducting tunnel junctions can seriously degrade the performance of quasiparticle (SIS) mixers operating in the submillimeter band, so it is essential to provide a circuit for tuning out this capacitance at the operating frequency. In this article, we present two new tuning circuits for SIS mixers which use a pair of SIS junctions connected by an inductance. Compared to previously proposed tuning circuits, ours have a broader bandwidth, are easier to scale to higher frequencies, and may be easier to fabricate. We have constructed quasi-optical mixers which employ these tuning circuits, using Nb/Al-Oxide/Nb SIS junctions defined by optical lithography. The performance of these devices is excellent, giving receiver noise temperatures of 113 K (DSB) at 490 GHz and 230 K DSB at 612 GHz. In addition to demonstrating the effectiveness of our tuning circuit, these results show that quasi-optical mixers can be competitive with or superior to waveguide mixers at submillimeter wavelengths. The mixers continue to perform well at frequencies up to 672 GHz, which is about 95% of the Nb gap frequency.>
The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>
An integrated superconducting microstrip is shown to be a convenient, flexible, and well characterized matching element for a superconductor-insulator-superconductor (SIS) heterodyne mixer. An open-circuited microstrip stub that reflects a parallel inductance across the junction is used to broaden the bandwidth of the RF match of a 30-40 GHz SIS mixer. Measurements with Pb-alloy junctions in a full-height waveguide mixer with fixed mechanical tuning give an instantaneous bandwidth of 10 to 15 percent with a mixer noise temperature T/sub M/(DSB)=10+-2.5 K.
Small area (<or=1- mu m/sup 2/), high-current-density NbN-MgO-NbN tunnel junctions with I-V characteristics suitable for high-frequency mixers have been fabricated. Mesa-geometry junctions with an area of about 1 mu m/sup 2/ and critical current density of 5-10 kA/cm/sup 2/ are integrated with superconducting microstrip lines designed to resonate out the junction capacitance. Accurate values of junction capacitance and magnetic penetration depth are required for the proper design of the microstrip. A study was made of the mixer gain and noise performance near 205 GHz as a function of the inductance provided by the microstrip line. This has confirmed, at a high millimeter-wave frequency, values of junction capacitance of 85 fF/ mu m/sup 2/ and recently measured values of a magnetic penetration depth of 380 nm. Mixer noise temperatures as low as 134 K at 1.5 K have been obtained for properly tuned junctions. A significant improvement in mixer performance on cooling from 4.2 K to 1.5 K was observed. Edge-geometry junctions with an area of 0.3 mu m/sup 3/ and critical current density of 18-25 kA/cm/sup 2/ have also been fabricated. These junctions give a mixer noise temperature of 145 K at 4.2 K without the use of integrated tuning elements. These are the best results ever achieved for NbN-based SIS mixers.