Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)

Design of a w-band SIS mixer

D. Winker

Published Dec 1, 1990• 0 citations
Publisher

Abstract

The mixer mount for a 75 -110 GHz SIS (superconductor-insulator-superconductor) receiver was scale modeled at 2 - 8 GHz . The mixer mount had a 4-step Chebychev single ridge transformer to launch the rf signal from the waveguide to a microstripline circuit. The microstripline circuit coupled the rf signal into the on-chip SIS element. A wire inductor in parallel with the mixer was used to tune out the capacitance of the SIS junction. Both the junction and the inductor had rf grounds provided by 90° radial stubs. In the scale model, a 50 Ω chip resistor in parallel with a 1 pF chip capacitor was used in place of the SIS junction to measure the rf matching properties. The inductor was modeled with a thin copper wire. The VSWR of the entire mount was less than 2.1 : 1 over the frequency band corresponding to 75 - 107 GHz. Receiver measurements with the actual mixer mount employing trilayer SIS tunnel junctions gave similar trends across the band.

DOI
10.1117/12.2301478

Related papers

A full-band waveguide SIS receiver with integrated tuning for 75-110 GHz

Dag Winkler, N. G. Ugras, A. Hodge Worsham +3 more

The performance of a broadband SIS (superconductor-insulator-superconductor) receiver with no mechanical tuning elements was modeled and tested. The mixer mount had a broadband-waveguide-to-microstripline transition consisting of a four-step Chebyshev single-ridge transformer. The last step of the ridge connected the waveguide to a microstripline circuit. The on-chip circuit consisted of a microstripline that transmitted the RF and the local oscillator signals to the SIS mixer. Both the SIS element and the inductor had RF grounds provided by 90 degrees radial stubs. The inductor tuned out the junction capacitance to allow operation over the full frequency band. The SIS element can be a single junction or series array using Nb-AlO/sub x/-Nb trilayer tunnel junctions with areas as small as 0.5 mu m/sup 2/ and V/sub m/(2 mV)=39 mV. Preliminary results indicated a DSB receiver noise temperature of 65-80 K across the band measured at 4.4 K with an internal cryogenic RF hot/cold source and with T/sub if/=21 K. With another device, a mixer noise temperature of 35 K at 100 GHz was achieved, increasing to 45 K at 79.5 and 110 GHz. Coupled mixer gain of up to +3 dB and negative dynamic resistance on the first photon step were observed. The lowest noise temperature was obtained for an untuned single-junction mixer at 80 GHz: T/sub R/=41 K and T/sub M/=20 K were measured.

IEEE Transactions on Magnetics•Mar 1, 1991•11 citations

A 100-GHz fixed-tuned waveguide SIS mixer exhibiting broad bandwidth and very low noise temperature

Sheng-Gai Shi, Takashi Noguchi, Junji Inatani

This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.

IEEE Transactions on Applied Superconductivity•Jan 1, 1997•22 citations

Development of a waveguide NbN-based SIS mixer in the 900-GHz band

Mahoto Takeda, Yoshinori Uzawa, Zhen Wang +2 more

We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•6 citations

An SIS mixer using two junctions connected in parallel

Takashi Noguchi, Sheng‐Cai Shi, Junji Inatani

We have fabricated a superconductor-insulator-superconductor (SIS) mixer using a couple of junctions connected in parallel through a stripline inductor. The junctions have significantly larger area, i.e. larger capacitance, and smaller normal resistance than conventional ones. In order to obtain a good impedance matching between the source and the junctions, an impedance transformer made of a superconducting stripline was integrated with the junctions. The capacitance of the junctions was tuned out by the inductor to obtain a broadband operation without mechanical tuning elements. It was shown that the double sideband noise temperature of the receiver employing this type of mixer device was less than 40 K over the bandwidth of 90-115 GHz. The lowest receiver noise temperature of /spl sim/20 K, which is only 4 times as large as the quantum limited photon noise of hv/k/sub B/, was obtained around 105 GHz.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•41 citations

120~180 GHz 대역 SIS(Superconductor-Insulator-Superconductor)접합 믹서의 개발

Moon‐Hee Chung, Changhoon Lee, Kwang-Dong Kim +3 more

A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.

The Journal of Korean Institute of Electromagnetic Engineering and Science•Jan 1, 2004•4 citations

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

IEICE Transactions on Electronics•Feb 1, 2006•5 citations
The mixer mount for a 75 -110 GHz SIS (superconductor-insulator-superconductor) receiver was scale modeled at 2 - 8 GHz . The mixer mount had a 4-step Chebychev single ridge transformer to launch the rf signal from the waveguide to a microstripline circuit. The microstripline circuit coupled the rf signal into the on-chip SIS element. A wire inductor in parallel with the mixer was used to tune out the capacitance of the SIS junction. Both the junction and the inductor had rf grounds provided by 90° radial stubs. In the scale model, a 50 Ω chip resistor in parallel with a 1 pF chip capacitor was used in place of the SIS junction to measure the rf matching properties. The inductor was modeled with a thin copper wire. The VSWR of the entire mount was less than 2.1 : 1 over the frequency band corresponding to 75 - 107 GHz. Receiver measurements with the actual mixer mount employing trilayer SIS tunnel junctions gave similar trends across the band.
The performance of a broadband SIS (superconductor-insulator-superconductor) receiver with no mechanical tuning elements was modeled and tested. The mixer mount had a broadband-waveguide-to-microstripline transition consisting of a four-step Chebyshev single-ridge transformer. The last step of the ridge connected the waveguide to a microstripline circuit. The on-chip circuit consisted of a microstripline that transmitted the RF and the local oscillator signals to the SIS mixer. Both the SIS element and the inductor had RF grounds provided by 90 degrees radial stubs. The inductor tuned out the junction capacitance to allow operation over the full frequency band. The SIS element can be a single junction or series array using Nb-AlO/sub x/-Nb trilayer tunnel junctions with areas as small as 0.5 mu m/sup 2/ and V/sub m/(2 mV)=39 mV. Preliminary results indicated a DSB receiver noise temperature of 65-80 K across the band measured at 4.4 K with an internal cryogenic RF hot/cold source and with T/sub if/=21 K. With another device, a mixer noise temperature of 35 K at 100 GHz was achieved, increasing to 45 K at 79.5 and 110 GHz. Coupled mixer gain of up to +3 dB and negative dynamic resistance on the first photon step were observed. The lowest noise temperature was obtained for an untuned single-junction mixer at 80 GHz: T/sub R/=41 K and T/sub M/=20 K were measured.
This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.
We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.
We have fabricated a superconductor-insulator-superconductor (SIS) mixer using a couple of junctions connected in parallel through a stripline inductor. The junctions have significantly larger area, i.e. larger capacitance, and smaller normal resistance than conventional ones. In order to obtain a good impedance matching between the source and the junctions, an impedance transformer made of a superconducting stripline was integrated with the junctions. The capacitance of the junctions was tuned out by the inductor to obtain a broadband operation without mechanical tuning elements. It was shown that the double sideband noise temperature of the receiver employing this type of mixer device was less than 40 K over the bandwidth of 90-115 GHz. The lowest receiver noise temperature of /spl sim/20 K, which is only 4 times as large as the quantum limited photon noise of hv/k/sub B/, was obtained around 105 GHz.>
A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.