Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chinese Physics B

Modulation depth of series SQUIDs modified by Josephson junction area*

Jie Liu, H. Gao, Gang Li, Zheng Wei Li, Kamal Ahmada, Zhang Ying Shan, Jianshe Liu, Wei Chen

Published Aug 1, 2017• 2 citations
Publisher

Abstract

The superconducting quantum interference device (SQUID) amplifier is widely used in the field of weak signal detection for its low input impedance, low noise, and low power consumption. In this paper, the SQUIDs with identical junctions and the series SQUIDs with different junctions were successfully fabricated. The Nb/Al-AlO x /Nb trilayer and input Nb coils were prepared by asputtering equipment. The SQUID devices were prepared by a sputtering and the lift-off method. Investigations by AFM, OM and SEM revealed the morphology and roughness of the Nb films and Nb/Al-AlO x /Nb trilayer. In addition, the current–voltage characteristics of the SQUID devices with identical junction and different junction areas were measured at 2.5 K in the He 3 refrigerator. The results show that the SQUID modulation depth is obviously affected by the junction area. The modulation depth obviously increases with the increase of the junction area in a certain range. It is found that the series SQUID with identical junction area has a transimpedance gain of 58 Ω approximately.

DOI
10.1088/1674-1056/26/9/098501

Related papers

Fabrication and characterization of the superconducting quantum interference device amplifier with Washer type input coil

Chen Zhao, He Gen-Fang, Qingya Zhang +3 more

Superconducting quantum interference device (SQUID) amplifier is best known for its low input impedance, low noise and low power consumption. Nowadays it is widely used for detecting the weak signals. Compared with other methods, the Nb/Al-AlOx/Nb structure Josephson junction based SQUID has the advantages of high transition temperature, high voltage flux modulation index and good heat recycle ability, wide critical voltage range, so it is a very good option for making SQUID amplifier. In this work, we fabricate the overdamped Josephson junction and washer dc SQUID, and test the I-V characteristics at He3 3 K stage temperature and calculate the current resolution of SQUID. The result of SQUID modulation property is good. The magnification becomes larger after increasing the input line number of loops, and the system noise becomes smaller after the join of the LC filter. This work is very important for designing and manufacturing transition edge sensor readout circuits.

Acta Physica Sinica•Jan 1, 2015•2 citations

Array of Superconducting Quantum Interference Devices with Multiturn Input Coil

T. Morooka, Hiroaki Myoren, S. Takada +1 more

Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.

Japanese Journal of Applied Physics•May 1, 2004•3 citations

Fabrication and Characteristics of All-NbN SQUID Series Array

Qiyu Zhang, Huiwu Wang, Xin Tang +2 more

In this article, an all-NbN superconducting quantum interference device (SQUID) array was developed for future applications by taking advantage of the higher critical temperature of a NbN film compared with Nb. The NbN SQUID array was composed of 100 SQUIDs with equal loop areas connected in series. The array was fabricated on a single-crystal MgO (100) substrate using 3-μm-diameter NbN/AlN/NbN Josephson junctions. The hysteresis and shielding parameters of the SQUID were 0.67 and 0.15, respectively. The SQUIDs in the array were coherently modulated by injecting current in a common flux control line, which resulted in a modulation voltage of 3.54 mV with consistent periodicity and a flux-to-voltage transfer coefficient of 23 mV/Φ0. Using a flux locked loop circuit, the fabricated NbN SQUID array exhibited excellent performance with a low white flux noise of 1.4 μΦ0/√Hz, which included the preamplifier noise.

IEEE Transactions on Applied Superconductivity•Aug 30, 2019•8 citations

A High-Performance Nb Nano-Superconducting Quantum Interference Device with a Three-Dimensional Structure

Lei Chen, Hao Wang, Xiaoyu Liu +2 more

A superconducting quantum interference device (SQUID) miniaturized into the nanoscale is promising in the inductive detection of a single electron spin. A nano-SQUID with a strong spin coupling coefficient, a low flux noise, and a wide working magnetic field range is highly desired in a single spin resonance measurement. Nano-SQUIDs with Dayem bridge junctions excel in a high working field range and in the direct coupling from spins to the bridge. However, the common planar structure of nano-SQUIDs is known for problems such as a shallow flux modulation depth and a troublesome hysteresis in current–voltage curves. Here, we developed a fabrication process for creating three-dimensional (3-D) niobium (Nb) nano-SQUIDs with nanobridge junctions that can be tuned independently. Characterization of the device shows up to 45.9% modulation depth with a reversible current–voltage curve. Owning to the large modulation depth, the measured flux noise is as low as 0.34 μΦ 0 /Hz 1/2 . The working field range of the SQUID is greater than 0.5 T parallel to the SQUID plane. We believe that 3-D Nb nano-SQUIDs provide a promising step toward effective single-spin inductive detection.

arXiv:1612.08149•Nano Letters•Nov 7, 2016•34 citations

Low noise DC SQUIDs fabricated in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology

M. B. Ketchen, Manjul Bhushan, Steven B. Kaplan +1 more

The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations

Multiloop Superconducting Quantum Interference Devices with Nb/Al-AlOx-Al/Nb Edge Junctions

Naoki Mizutani, Gen Uehara, Youichi Takada +2 more

We have fabricated multiloop superconducting quantum interference devices (SQUIDs) of 4×4 mm2 total size using sub-µ m Nb/Al-AlO x -Al/Nb edge junctions. We obtained very large voltage swing and gradient ∂V/∂Φ of 0.95-1.53 mV/Φ0, because it was possible to increase the shunt resistance due to the small junction capacitance. This advantage enabled us to achieve very low flux density noise of 1.9 fT/Hz0.5 for white noise by using a readout circuit in which the voltage noise of the amplifier was 1.4 nV/Hz0.5. The low-frequency noise was also very low (7.3 fT/Hz0.5 at 1 Hz). These noise results are half and one-third, respectively, compared with noise before the improvement achieved by this study. We obtained very low flux density noise for the small SQUID using only an inexpensive, compact readout circuit.

Japanese Journal of Applied Physics•Sep 1, 1995•0 citations
The superconducting quantum interference device (SQUID) amplifier is widely used in the field of weak signal detection for its low input impedance, low noise, and low power consumption. In this paper, the SQUIDs with identical junctions and the series SQUIDs with different junctions were successfully fabricated. The Nb/Al-AlO x /Nb trilayer and input Nb coils were prepared by asputtering equipment. The SQUID devices were prepared by a sputtering and the lift-off method. Investigations by AFM, OM and SEM revealed the morphology and roughness of the Nb films and Nb/Al-AlO x /Nb trilayer. In addition, the current–voltage characteristics of the SQUID devices with identical junction and different junction areas were measured at 2.5 K in the He 3 refrigerator. The results show that the SQUID modulation depth is obviously affected by the junction area. The modulation depth obviously increases with the increase of the junction area in a certain range. It is found that the series SQUID with identical junction area has a transimpedance gain of 58 Ω approximately.
Superconducting quantum interference device (SQUID) amplifier is best known for its low input impedance, low noise and low power consumption. Nowadays it is widely used for detecting the weak signals. Compared with other methods, the Nb/Al-AlOx/Nb structure Josephson junction based SQUID has the advantages of high transition temperature, high voltage flux modulation index and good heat recycle ability, wide critical voltage range, so it is a very good option for making SQUID amplifier. In this work, we fabricate the overdamped Josephson junction and washer dc SQUID, and test the I-V characteristics at He3 3 K stage temperature and calculate the current resolution of SQUID. The result of SQUID modulation property is good. The magnification becomes larger after increasing the input line number of loops, and the system noise becomes smaller after the join of the LC filter. This work is very important for designing and manufacturing transition edge sensor readout circuits.
Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.
In this article, an all-NbN superconducting quantum interference device (SQUID) array was developed for future applications by taking advantage of the higher critical temperature of a NbN film compared with Nb. The NbN SQUID array was composed of 100 SQUIDs with equal loop areas connected in series. The array was fabricated on a single-crystal MgO (100) substrate using 3-μm-diameter NbN/AlN/NbN Josephson junctions. The hysteresis and shielding parameters of the SQUID were 0.67 and 0.15, respectively. The SQUIDs in the array were coherently modulated by injecting current in a common flux control line, which resulted in a modulation voltage of 3.54 mV with consistent periodicity and a flux-to-voltage transfer coefficient of 23 mV/Φ0. Using a flux locked loop circuit, the fabricated NbN SQUID array exhibited excellent performance with a low white flux noise of 1.4 μΦ0/√Hz, which included the preamplifier noise.
A superconducting quantum interference device (SQUID) miniaturized into the nanoscale is promising in the inductive detection of a single electron spin. A nano-SQUID with a strong spin coupling coefficient, a low flux noise, and a wide working magnetic field range is highly desired in a single spin resonance measurement. Nano-SQUIDs with Dayem bridge junctions excel in a high working field range and in the direct coupling from spins to the bridge. However, the common planar structure of nano-SQUIDs is known for problems such as a shallow flux modulation depth and a troublesome hysteresis in current–voltage curves. Here, we developed a fabrication process for creating three-dimensional (3-D) niobium (Nb) nano-SQUIDs with nanobridge junctions that can be tuned independently. Characterization of the device shows up to 45.9% modulation depth with a reversible current–voltage curve. Owning to the large modulation depth, the measured flux noise is as low as 0.34 μΦ 0 /Hz 1/2 . The working field range of the SQUID is greater than 0.5 T parallel to the SQUID plane. We believe that 3-D Nb nano-SQUIDs provide a promising step toward effective single-spin inductive detection.
The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.
We have fabricated multiloop superconducting quantum interference devices (SQUIDs) of 4×4 mm2 total size using sub-µ m Nb/Al-AlO x -Al/Nb edge junctions. We obtained very large voltage swing and gradient ∂V/∂Φ of 0.95-1.53 mV/Φ0, because it was possible to increase the shunt resistance due to the small junction capacitance. This advantage enabled us to achieve very low flux density noise of 1.9 fT/Hz0.5 for white noise by using a readout circuit in which the voltage noise of the amplifier was 1.4 nV/Hz0.5. The low-frequency noise was also very low (7.3 fT/Hz0.5 at 1 Hz). These noise results are half and one-third, respectively, compared with noise before the improvement achieved by this study. We obtained very low flux density noise for the small SQUID using only an inexpensive, compact readout circuit.