Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Japanese Journal of Applied Physics

Multiloop Superconducting Quantum Interference Devices with Nb/Al-AlOx-Al/Nb Edge Junctions

Naoki Mizutani, Gen Uehara, Youichi Takada, Akira Adachi, Hisashi Kado

Published Sep 1, 1995• 0 citations
Publisher

Abstract

We have fabricated multiloop superconducting quantum interference devices (SQUIDs) of 4×4 mm2 total size using sub-µ m Nb/Al-AlO x -Al/Nb edge junctions. We obtained very large voltage swing and gradient ∂V/∂Φ of 0.95-1.53 mV/Φ0, because it was possible to increase the shunt resistance due to the small junction capacitance. This advantage enabled us to achieve very low flux density noise of 1.9 fT/Hz0.5 for white noise by using a readout circuit in which the voltage noise of the amplifier was 1.4 nV/Hz0.5. The low-frequency noise was also very low (7.3 fT/Hz0.5 at 1 Hz). These noise results are half and one-third, respectively, compared with noise before the improvement achieved by this study. We obtained very low flux density noise for the small SQUID using only an inexpensive, compact readout circuit.

DOI
10.1143/jjap.34.l1130

Related papers

Fabrication and Evaluation of Superconducting Quantum Interference Devices with Nb/Al–AlOx–Al/Nb Edge Junctions

Naoki Mizutani, Shuichi Yamasaki, Youichi Takada +2 more

We have fabricated superconducting quantum interference devices (SQUIDs) with an inductance of 140 pH by using sub- µm Nb/Al–AlO x –Al/Nb edge junctions. The small capacitance of the junction resulted in the very large voltage swing of 210 µV and gradient dV/ dΦ of 940 µV/Φ0. Consequently, the very low flux noise of 0.61 µΦ0/ Hz0.5 corresponding to the energy sensitivity ε of 8.6h at the white noise level was obtained by using a conventional flux-locked loop configuration. The low-frequency noise was also very low, 2.7 µΦ0/ Hz0.5 corresponding to ε= 170 h at 1 Hz. We could obtain very low flux noise for the SQUID which had the practical inductance using only a conventional readout circuit.

Japanese Journal of Applied Physics•May 1, 1994•5 citations

Nearly quantum limited nanoSQUIDs based on cross-type Nb/AlO x /Nb junctions

Matthias Schmelz, V Zakosarenko, Thomas Schönau +4 more

Abstract We report on the development of nearly quantum limited SQUIDs with miniature pickup loop dimensions. The implemented high quality and low capacitance cross-type Nb/AlO x /Nb Josephson junctions offer large I C R N -products and therefore enable an exceptional low noise level of the SQUIDs. Devices with loop dimensions of 1 μ m exhibit white flux noise levels as low as 45 nΦ 0 Hz −1/2 corresponding to an energy resolution ε of about 1 h at 4.2 K, with h being Planck’s constant. Moreover, the large usable voltage swings of the devices of about 300 μ V allow highly sensitive and easy single-stage operation while exploring nearly the intrinsic noise of the SQUIDs, beneficial e.g. for sensor arrays in SQUID microscopy.

arXiv:1705.06166•Superconductor Science and Technology•Nov 2, 2016•23 citations

Excess low-frequency flux noise in dc SQUIDs

M. E. Huber, Michael W. Cromar, Ronald H. Ono

We have fabricated dc superconducting quantum interference devices (SQUIDs) incorporating Nb/Al-oxide/Nb Josephson junctions in both stripline and washer geometries. Low-frequency noise in excess of that predicted by the resistively-shunted junction model is present in both geometries and is demonstrated to be flux noise. This flux noise is not environmental. Improvements in fabrication processing over the past four years have reduced the level of this flux noise. SQUIDs are now fabricated with PdAu resistors, Nb wiring layers, and SiO/sub 2/ interlayer dielectric. In our best well-coupled SQUIDs, the white-noise energy sensitivity is 5/spl times/10/sup -31/ J/spl middot/s, with a 1/f knee below 0.1 Hz. We believe further reduction in the flux noise might be obtained with the use of on-chip flux shielding and/or trapping structures.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•6 citations

Investigation of all niobium nano-SQUIDs based on sub-micrometer cross-type Josephson junctions

Matthias Schmelz, Y Matsui, Ronny Stolz +6 more

We report on the development of highly sensitive SQUIDs featuring sub-micrometer loop dimensions. The integration of high quality and low capacitance SIS Nb/AlO x /Nb cross-type Josephson tunnel junctions results in white flux noise levels as low as 66 n Φ 0 Hz −1/2 , well below state-of-the-art values of their Nb-based counterparts based on constriction type junctions. Estimation of the spin sensitivity of the best SQUIDs yield S μ 1/2 < 7 μ B Hz −1/2 in the white noise region, suitable for the investigation of small spin systems. We discuss fabrication challenges, show results on the electrical characterization of devices with various pickup loops, and describe options for further improvement, which may push the sensitivity of such devices even to single spin resolution.

arXiv:1501.00958•Superconductor Science and Technology•Nov 26, 2014•27 citations

Low noise DC SQUIDs fabricated in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology

M. B. Ketchen, Manjul Bhushan, Steven B. Kaplan +1 more

The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations

3D nanoSQUID based on tunnel nano-junctions with an energy sensitivity of 1.3 h at 4.2 K

Matthias Schmelz, Antonio Vettoliere, V. Zakosarenko +4 more

We report the performance of a reliable three-dimensional nanometer-sized Superconducting QUantum Interference Device (SQUID). The use of superconductor-isolator-superconductor Nb/Al-AlOx/Nb Josephson tunnel junctions together with small SQUID loop dimensions permits a high modulation depth of the SQUID's critical current and thus leads to very low intrinsic flux noise of the device. In particular, we present electrical characterization including detailed noise investigations. At 4.2 K, two-stage noise measurements with a SQUID as a low noise preamplifier result in a white flux noise of 51 nΦ0/Hz1/2, which is equivalent to an energy resolution of 1.3 h, with h being Planck's constant. Simulation of spin sensitivities results in about 1 μB/Hz1/2 for an electron spin positioned directly above the SQUID ring.

Applied Physics Letters•Jul 17, 2017•18 citations
We have fabricated multiloop superconducting quantum interference devices (SQUIDs) of 4×4 mm2 total size using sub-µ m Nb/Al-AlO x -Al/Nb edge junctions. We obtained very large voltage swing and gradient ∂V/∂Φ of 0.95-1.53 mV/Φ0, because it was possible to increase the shunt resistance due to the small junction capacitance. This advantage enabled us to achieve very low flux density noise of 1.9 fT/Hz0.5 for white noise by using a readout circuit in which the voltage noise of the amplifier was 1.4 nV/Hz0.5. The low-frequency noise was also very low (7.3 fT/Hz0.5 at 1 Hz). These noise results are half and one-third, respectively, compared with noise before the improvement achieved by this study. We obtained very low flux density noise for the small SQUID using only an inexpensive, compact readout circuit.
We have fabricated superconducting quantum interference devices (SQUIDs) with an inductance of 140 pH by using sub- µm Nb/Al–AlO x –Al/Nb edge junctions. The small capacitance of the junction resulted in the very large voltage swing of 210 µV and gradient dV/ dΦ of 940 µV/Φ0. Consequently, the very low flux noise of 0.61 µΦ0/ Hz0.5 corresponding to the energy sensitivity ε of 8.6h at the white noise level was obtained by using a conventional flux-locked loop configuration. The low-frequency noise was also very low, 2.7 µΦ0/ Hz0.5 corresponding to ε= 170 h at 1 Hz. We could obtain very low flux noise for the SQUID which had the practical inductance using only a conventional readout circuit.
Abstract We report on the development of nearly quantum limited SQUIDs with miniature pickup loop dimensions. The implemented high quality and low capacitance cross-type Nb/AlO x /Nb Josephson junctions offer large I C R N -products and therefore enable an exceptional low noise level of the SQUIDs. Devices with loop dimensions of 1 μ m exhibit white flux noise levels as low as 45 nΦ 0 Hz −1/2 corresponding to an energy resolution ε of about 1 h at 4.2 K, with h being Planck’s constant. Moreover, the large usable voltage swings of the devices of about 300 μ V allow highly sensitive and easy single-stage operation while exploring nearly the intrinsic noise of the SQUIDs, beneficial e.g. for sensor arrays in SQUID microscopy.
We have fabricated dc superconducting quantum interference devices (SQUIDs) incorporating Nb/Al-oxide/Nb Josephson junctions in both stripline and washer geometries. Low-frequency noise in excess of that predicted by the resistively-shunted junction model is present in both geometries and is demonstrated to be flux noise. This flux noise is not environmental. Improvements in fabrication processing over the past four years have reduced the level of this flux noise. SQUIDs are now fabricated with PdAu resistors, Nb wiring layers, and SiO/sub 2/ interlayer dielectric. In our best well-coupled SQUIDs, the white-noise energy sensitivity is 5/spl times/10/sup -31/ J/spl middot/s, with a 1/f knee below 0.1 Hz. We believe further reduction in the flux noise might be obtained with the use of on-chip flux shielding and/or trapping structures.
We report on the development of highly sensitive SQUIDs featuring sub-micrometer loop dimensions. The integration of high quality and low capacitance SIS Nb/AlO x /Nb cross-type Josephson tunnel junctions results in white flux noise levels as low as 66 n Φ 0 Hz −1/2 , well below state-of-the-art values of their Nb-based counterparts based on constriction type junctions. Estimation of the spin sensitivity of the best SQUIDs yield S μ 1/2 < 7 μ B Hz −1/2 in the white noise region, suitable for the investigation of small spin systems. We discuss fabrication challenges, show results on the electrical characterization of devices with various pickup loops, and describe options for further improvement, which may push the sensitivity of such devices even to single spin resolution.
The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.
We report the performance of a reliable three-dimensional nanometer-sized Superconducting QUantum Interference Device (SQUID). The use of superconductor-isolator-superconductor Nb/Al-AlOx/Nb Josephson tunnel junctions together with small SQUID loop dimensions permits a high modulation depth of the SQUID's critical current and thus leads to very low intrinsic flux noise of the device. In particular, we present electrical characterization including detailed noise investigations. At 4.2 K, two-stage noise measurements with a SQUID as a low noise preamplifier result in a white flux noise of 51 nΦ0/Hz1/2, which is equivalent to an energy resolution of 1.3 h, with h being Planck's constant. Simulation of spin sensitivities results in about 1 μB/Hz1/2 for an electron spin positioned directly above the SQUID ring.