Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

The Japan Society of Applied Physics

Fabrication process of NbN integrated circuit for superconducting qubit

Hirotaka Terai

Published Feb 13, 2013• 0 citations
OpenAlex

Related papers

Fabrication of NbN/AlN/CuNi/NbN ferromagnetic Josephson junctions toward superconducting qubit

悠輝 加藤, 颯 中村, 雅光 田中 +2 more

IEICE Technical Report; IEICE Tech. Rep.•Oct 2, 2019•0 citations

Fabrication and measurement of superconducting qubits consisting of fully-epitaxial NbN-based Josephson junctions

Hirotaka Terai, Sunmi Kim, Tomoko Fuse +4 more

The Japan Society of Applied Physics•Jul 10, 2019•0 citations

Fabrication of Superconducting NbN Gate MOSFET for Hybrid Circuit Applications

Nobuhiro Suzuki, Keiji Yamamoto, Satoshi Matsumoto +3 more

International Conference on Solid State Devices and Materials (SSDM)•Aug 24, 1994•4 citations

Fabrication Process for Monolithic Integration of a Nitride Superconductor-Based Superconducting Qubit with a Single Flux Quantum Control Circuit

Shigeyuki Miyajima, Taro Yamashita, Masamitsu Tanaka +3 more

We developed a process for fabricating nitride superconductor-based superconducting qubits monolithically integrated with a single flux quantum (SFQ)-based readout and control circuits. Since we used a Josephson junction (JJ) made of an NbN/AlN/NbN tri-layer, including a critical current density (Jc) of 50 A/cm2as the suitable material for superconducting qubits and SFQ readout/control circuits operating at 20 mK, the JJs for both the qubits and the SFQ circuits could simultaneously be fabricated. The device structure was also composed of three superconductive layers, comprising two superconductive layers as wiring layers and other layers as the top ground plane. Then, we used a Pd film as the resistive layer, which is required as the shunt resistors and the bias resistors for the SFQ control circuits, followed by an investigation of the properties of NbN/AlN/NbN epitaxial junctions and evaluation of the sheet inductance of the base NbN and wiring NbTiN layer. Our results showed the successful fabrication of a JJ with a sufficiently low leakage current and aJcof around 50 A/cm2, which was close to the target value. Furthermore, the evaluated sheet inductance exceeded 1 pH, which was several times larger than the values obtained for Nb-integrated circuits.

IEEE Transactions on Applied Superconductivity•Feb 1, 2023•11 citations

Sidewall spacer passivated epitaxial NbN/AlN/NbN Josephson junctions for superconducting qubit applications

Koki Honda, Daiki Kurihara, Hiroki Kutsuma +2 more

Epitaxial NbN/AlN/NbN Josephson junctions are promising alternatives to conventional Al/AlO$_x$/Al junctions for superconducting qubits due to their crystalline tunnel barriers and the high transition temperature of NbN. However, their integration into quantum circuits typically requires complex fabrication processes involving amorphous interlayer dielectrics, which can degrade qubit coherence times. To address these issues, we developed sidewall spacer passivated epitaxial NbN/AlN/NbN junctions using a fabrication process that reduces both the volume of amorphous dielectric material and fabrication complexity. The fabricated junctions exhibited a large gap voltage of approximately 5.6 mV and low subgap leakage currents. By varying the thickness of the AlN tunnel barrier, high-quality junctions were fabricated over a wide range of critical current densities ${\it J}_c$, from 0.3 to 10$^4$ A/cm$^2$. In addition, the comparison of the current-voltage characteristics before and after buffered hydrofluoric acid treatment indicated that the wet etching process did not degrade the electrical characteristics of the junctions. These results establish a scalable fabrication process for epitaxial Josephson junctions and provide a promising platform for high-coherence nitride-based superconducting qubits.

quant-pharXiv:2610.04820•Oct 6, 2026•0 citations

NbN-based superconducting qubit on Si substrate

Sunmi Kim, Tomoko Fuse, Fumiki Yoshihara +5 more

Bulletin of the American Physical Society•Mar 6, 2020•0 citations
We developed a process for fabricating nitride superconductor-based superconducting qubits monolithically integrated with a single flux quantum (SFQ)-based readout and control circuits. Since we used a Josephson junction (JJ) made of an NbN/AlN/NbN tri-layer, including a critical current density (Jc) of 50 A/cm2as the suitable material for superconducting qubits and SFQ readout/control circuits operating at 20 mK, the JJs for both the qubits and the SFQ circuits could simultaneously be fabricated. The device structure was also composed of three superconductive layers, comprising two superconductive layers as wiring layers and other layers as the top ground plane. Then, we used a Pd film as the resistive layer, which is required as the shunt resistors and the bias resistors for the SFQ control circuits, followed by an investigation of the properties of NbN/AlN/NbN epitaxial junctions and evaluation of the sheet inductance of the base NbN and wiring NbTiN layer. Our results showed the successful fabrication of a JJ with a sufficiently low leakage current and aJcof around 50 A/cm2, which was close to the target value. Furthermore, the evaluated sheet inductance exceeded 1 pH, which was several times larger than the values obtained for Nb-integrated circuits.
Epitaxial NbN/AlN/NbN Josephson junctions are promising alternatives to conventional Al/AlOx_xx​/Al junctions for superconducting qubits due to their crystalline tunnel barriers and the high transition temperature of NbN. However, their integration into quantum circuits typically requires complex fabrication processes involving amorphous interlayer dielectrics, which can degrade qubit coherence times. To address these issues, we developed sidewall spacer passivated epitaxial NbN/AlN/NbN junctions using a fabrication process that reduces both the volume of amorphous dielectric material and fabrication complexity. The fabricated junctions exhibited a large gap voltage of approximately 5.6 mV and low subgap leakage currents. By varying the thickness of the AlN tunnel barrier, high-quality junctions were fabricated over a wide range of critical current densities Jc{\it J}_cJc​, from 0.3 to 104^44 A/cm2^22. In addition, the comparison of the current-voltage characteristics before and after buffered hydrofluoric acid treatment indicated that the wet etching process did not degrade the electrical characteristics of the junctions. These results establish a scalable fabrication process for epitaxial Josephson junctions and provide a promising platform for high-coherence nitride-based superconducting qubits.