Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

A laser diode system and its use in a laser cooling experiment

C. C. Bradley

Published Jan 1, 1992• 0 citations
OpenAlex

Abstract

A system to control and stabilize the output of visible laser diodes was developed and used to measure the velocity distribution of lithium atoms in a laser cooling experiment. Circuitry was designed and built for controlling the diode temperature and current, and optical feedback from a grating was used to further tune the laser and to narrow its lineshape. In the experiment, atoms from a thermal lithium beam were slowed to near zero velocity using a multi-frequency relay chirp technique.

Related papers

Laser cooling of lithium using relay chirp cooling

C. C. Bradley, J. G. Story, J. J. Tollett +3 more

We demonstrate a chirp-cooling technique that uses a laser with multiple FM sidebands to slow lithium atoms from initial velocities of as much as 1880 m/s to final velocities near zero. Compared with the use of a single sideband, this multisideband technique significantly reduces FM bandwidth requirements and provides a greater flux of slowed atoms.

Optics Letters•Mar 1, 1992•19 citations

Cooling cesium atoms using diode lasers

Carl Wieman, R. N. Watts

We have cooled and stopped a beam of cesium atoms using frequency chirped diode lasers. In this technique, a moving atom absorbs and reemits many photons from a counter propagating laser that is frequency swept to keep it in resonance with an atomic transition. The resulting momentum transfer slows the atom. The basic approach is identical to that developed by Hall and co-workers, however, the use of diode lasers allows us to obtain the necessary frequency modulation simply by sweeping the laser injection current. We use two diode lasers tuned to each of the 6s hyperfine ground state levels to drive the 6s—6p3/2 transitions. Each laser is simultaneously swept over the Doppler profile of the 100°C thermal cesium beam to bring a substantial number to a stop. Using additional fast frequency modulation, the same lasers are used to probe the resulting velocity distribution. This technique allows us to bring ~106 atoms/cm3 to a temperature of 1 K. This method is an extremely simple and inexpensive way to produce cold atoms.

International Laser Science Conference•Jan 1, 1986•0 citations

Manipulating atomic velocities using diode lasers

Richard N. Watts, Carl Wieman

We have used counterpropagating radiation from a diode laser to cool and stop a beam of cesium atoms. The laser frequency was chirped to keep it in resonance with the slowing atoms. The same laser was used to probe the resulting velocity distributions. We have cooled more than 10 10 atoms/sec to a temperature of 1 K. This is an extremely simple and inexpensive way to manipulate atomic velocities and has a wide range of possible applications.

WORLD SCIENTIFIC eBooks•Jan 1, 2008•0 citations

Laser cooling and trapping of rubidium

Christopher D. Wallace, Timothy T. Grove, T. Dinneen +2 more

We have laser cooled an atomic beam of rubidium with diode lasers and have used these slow atoms to load a magneto-optical trap. The cooling is performed with the frequency-chirp method,1,2 in which the laser's frequency is ramped linearly (by the injection currant) to maintain resonance with the decelerating atoms. Two synchronously chirped lasers are required to prevent optical hyperfine pumping of the ground state. The chirp typically covers 500 MHz in 10 ms. At the end of each ramp, the resulting velocity distribution is measured with a pulsed probe laser. By varying the end point of the chirp, we are able to obtain slow atoms with average velocities ranging from 200 to −50 m/s. The widths of the velocity distributions are measured to be approximately 40 m/s. This relatively large width results from the inherent linewidth (~30 MHz) of the free-running diode lasers used for both cooling and probing.

Quantum Electronics and Laser Science Conference•May 12, 1991•0 citations

Manipulating atomic velocities using diode lasers

Richard N. Watts, Carl Wieman

We have used counterpropagating radiation from a diode laser to cool and stop a beam of cesium atoms. The laser frequency was chirped to keep it in resonance with the slowing atoms. The same laser was used to probe the resulting velocity distributions. We have cooled more than 1010 atoms/sec to a temperature of 1 K. This is an extremely simple and inexpensive way to manipulate atomic velocities and has a wide range of possible applications.

Optics Letters•May 1, 1986•86 citations

Deceleration of a thermal beam of Rb

B. Sheehy, S. Hatamian, Richard N. Watts +1 more

We have used diode laser beams that counter- propagate against a thermal beam of Rb to decelerate the atoms to near-zero velocity and bunch their speeds into a very narrow range. As the atoms decelerate, their changing Doppler shift is compensated by increasing the laser frequency. This chirping is easily accomplished with diode lasers because of their strong frequency dependence on current.

Quantum Electronics and Laser Science Conference•Apr 24, 1989•0 citations
A system to control and stabilize the output of visible laser diodes was developed and used to measure the velocity distribution of lithium atoms in a laser cooling experiment. Circuitry was designed and built for controlling the diode temperature and current, and optical feedback from a grating was used to further tune the laser and to narrow its lineshape. In the experiment, atoms from a thermal lithium beam were slowed to near zero velocity using a multi-frequency relay chirp technique.
We have cooled and stopped a beam of cesium atoms using frequency chirped diode lasers. In this technique, a moving atom absorbs and reemits many photons from a counter propagating laser that is frequency swept to keep it in resonance with an atomic transition. The resulting momentum transfer slows the atom. The basic approach is identical to that developed by Hall and co-workers, however, the use of diode lasers allows us to obtain the necessary frequency modulation simply by sweeping the laser injection current. We use two diode lasers tuned to each of the 6s hyperfine ground state levels to drive the 6s—6p3/2 transitions. Each laser is simultaneously swept over the Doppler profile of the 100°C thermal cesium beam to bring a substantial number to a stop. Using additional fast frequency modulation, the same lasers are used to probe the resulting velocity distribution. This technique allows us to bring ~106 atoms/cm3 to a temperature of 1 K. This method is an extremely simple and inexpensive way to produce cold atoms.
We have laser cooled an atomic beam of rubidium with diode lasers and have used these slow atoms to load a magneto-optical trap. The cooling is performed with the frequency-chirp method,1,2 in which the laser's frequency is ramped linearly (by the injection currant) to maintain resonance with the decelerating atoms. Two synchronously chirped lasers are required to prevent optical hyperfine pumping of the ground state. The chirp typically covers 500 MHz in 10 ms. At the end of each ramp, the resulting velocity distribution is measured with a pulsed probe laser. By varying the end point of the chirp, we are able to obtain slow atoms with average velocities ranging from 200 to −50 m/s. The widths of the velocity distributions are measured to be approximately 40 m/s. This relatively large width results from the inherent linewidth (~30 MHz) of the free-running diode lasers used for both cooling and probing.