Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconducting Multilayer Technology for Josephson Devices : Technology, Engineering, Physics, Applications

J. M. Meckbach

Published Jan 1, 2013• 5 citations
Publisher

Abstract

Within this book fabrication processes for high-quality Josephson junctions based on niobium and aluminum oxide as well as niobium nitride and aluminum nitride on various substrates are discussed. Techniques for achieving a planar chip topography and sub-µm lateral dimensions, aiding the realization of sophisticated Josephson devices such as SQUIDs, flux-flow oscillators and long Josephson junctions with artificial phase discontinuities, are presented in detail.

DOI
10.5445/ksp/1000036875

Related papers

Sub-$\mu\hbox{m}$ Josephson Junctions for Superconducting Quantum Devices

J. M. Meckbach, Michael Merker, Simon J. Buehler +7 more

For high-performance superconducting quantum devices based on Josephson junctions (JJs), decreasing lateral sizes is of great importance. Fabrication of sub-μm JJs is challenging, due to nonflat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-and-match process, combining electron-beam lithography and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 μm2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing procedure. Transport measurements of JJs, having critical-current densities ranging from 50 to 104A/cm2, are presented at 4.2 K. Our JJ process yields excellent quality parameters, Rsg/RNup to ~ 50, Vmfrom 15 to 80 mV and Vgapup to 2.81 mV, and also allows the fabrication of high-quality, sub-μm wide, long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub- μm JJs for quantum devices such as SQUIDs, qubits, and SIS mixers.

arXiv:1210.1012•IEEE Transactions on Applied Superconductivity•Dec 4, 2012•11 citations

Towards Fabrication of Sub-Micrometer Cross-Type Aluminum Josephson Junctions

Stephan Mechold, Katja Peiselt, Matthias Schmelz +5 more

The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.

IEEE Transactions on Applied Superconductivity•Dec 18, 2023•2 citations

A simple and robust niobium Josephson junction integrated circuit process

Andrew T. Barfknecht, Rich Ruby, H.L. Ko

A simple and robust process for fabricating low-T/sub c/ Josephson junction integrated circuits has been developed. The process is designed around the Nb/Al/sub 2/O/sub 3/-Al/Nb trilayer, and utilized nine masking steps to form two separate levels of trilayer Josephson junctions, as well as resistors, capacitors, and transmission lines. Materials used for interlayer dielectrics and passivation layers are silicon dioxide and silicon nitride formed by plasma-enhanced chemical vapor deposition (PECVD). The PECVD equipment yields a high deposition rate at moderate substrate temperatures. No degradation of the junction characteristics due to these depositions is seen. The measured loss tangent of this dielectric at 10 GHz using a parallel plate technique is 4.44*10/sup -4/. The dielectric constant of this material is 5.1 in the range of 50 to 400 GHz, measured using an on-chip resonator capacitively coupled to a single shunted Josephson junction. The physical quality of the oxide has been investigated using a variety of tests and has proven to be excellent. A variety of simple circuits using this process technology have been fabricated and tested. More complex circuits are currently under development.

IEEE Transactions on Magnetics•Mar 1, 1991•35 citations

Vortices in long Josephson junctions

J.E. Nordman, James B. Beyer

Research during the initial year of this grant concentrated on fabrication and modelling of long Josephson junction structures. A particular effort was made to understand the basic operating mechanisms of a type of superconducting transistor, the vortex flow transistor, and to optimize its circuit performance. Fabrication techniques were developed using niobium and lead superconductors. These techniques allow rapid production of a variety of device shapes. An optimization of geometric configuration was made to produce the most desirable device characteristics. Amplification was observed at low frequencies and initial coupling circuit designs were made to enable high frequency measurement. Development of potentially more versatile fabrication techniques using niobium and niobium nitride was also begun, as was a simulation study aimed primarily at understanding spatially nonuniform long junction structures.

Final Report•Feb 1, 1989•0 citations

High-Quality Ferromagnetic Josephson Junctions Based on Aluminum Electrodes

Antonio Vettoliere, Roberta Satariano, Raffaella Ferraiuolo +9 more

Aluminum Josephson junctions are the building blocks for the realization of superconducting quantum bits. Attention has been also paid to hybrid ferromagnetic Josephson junctions, which allow switching between different magnetic states, making them interesting for applications such as cryogenic memories, single-photon detectors, and spintronics. In this paper, we report on the fabrication and characterization of high-quality ferromagnetic Josephson junctions based on aluminum technology. We employed an innovative fabrication process inspired by niobium-based technology, allowing us to obtain very high-quality hybrid aluminum Josephson junctions; thus, supporting the use of ferromagnetic Josephson junctions in advanced quantum circuits. The fabrication process is described in detail and the main DC transport properties at low temperatures (current-voltage characteristic, critical current as a function of the temperature, and the external magnetic field) are reported. Here, we illustrate in detail the fabrication process, as well as the main DC transport properties at low temperatures (current-voltage characteristic, critical current as a function of the temperature, and the external magnetic field).

Nanomaterials•Nov 24, 2022•18 citations

Substrate insulated Josephson junctions for superconducting quantum circuits

Urs Strobel, L. Radtke, Larissa Kamps +9 more

We have developed a fabrication technique for Josephson junctions that employs a three-dimensional patterned, low-loss substrate instead of commonly used organic resists. The technique enables the fabrication of high-quality trilayer junctions from a wide range of geometries and materials, including high-melting-point superconductors such as tantalum or niobium. The junction electrodes are free from intentionally introduced oxides and organic materials, which are known sources of decoherence. We fabricate and characterize underdamped Nb/AlOx/Nb junctions of different sizes in several geometries.

arXiv:2606.12262•Applied Physics Letters•Sep 28, 2026•0 citations
Within this book fabrication processes for high-quality Josephson junctions based on niobium and aluminum oxide as well as niobium nitride and aluminum nitride on various substrates are discussed. Techniques for achieving a planar chip topography and sub-µm lateral dimensions, aiding the realization of sophisticated Josephson devices such as SQUIDs, flux-flow oscillators and long Josephson junctions with artificial phase discontinuities, are presented in detail.
Sub-μm\mu\hbox{m}μm Josephson Junctions for Superconducting Quantum Devices
For high-performance superconducting quantum devices based on Josephson junctions (JJs), decreasing lateral sizes is of great importance. Fabrication of sub-μm JJs is challenging, due to nonflat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-and-match process, combining electron-beam lithography and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 μm2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing procedure. Transport measurements of JJs, having critical-current densities ranging from 50 to 104A/cm2, are presented at 4.2 K. Our JJ process yields excellent quality parameters, Rsg/RNup to ~ 50, Vmfrom 15 to 80 mV and Vgapup to 2.81 mV, and also allows the fabrication of high-quality, sub-μm wide, long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub- μm JJs for quantum devices such as SQUIDs, qubits, and SIS mixers.
The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.
A simple and robust process for fabricating low-T/sub c/ Josephson junction integrated circuits has been developed. The process is designed around the Nb/Al/sub 2/O/sub 3/-Al/Nb trilayer, and utilized nine masking steps to form two separate levels of trilayer Josephson junctions, as well as resistors, capacitors, and transmission lines. Materials used for interlayer dielectrics and passivation layers are silicon dioxide and silicon nitride formed by plasma-enhanced chemical vapor deposition (PECVD). The PECVD equipment yields a high deposition rate at moderate substrate temperatures. No degradation of the junction characteristics due to these depositions is seen. The measured loss tangent of this dielectric at 10 GHz using a parallel plate technique is 4.44*10/sup -4/. The dielectric constant of this material is 5.1 in the range of 50 to 400 GHz, measured using an on-chip resonator capacitively coupled to a single shunted Josephson junction. The physical quality of the oxide has been investigated using a variety of tests and has proven to be excellent. A variety of simple circuits using this process technology have been fabricated and tested. More complex circuits are currently under development.
Research during the initial year of this grant concentrated on fabrication and modelling of long Josephson junction structures. A particular effort was made to understand the basic operating mechanisms of a type of superconducting transistor, the vortex flow transistor, and to optimize its circuit performance. Fabrication techniques were developed using niobium and lead superconductors. These techniques allow rapid production of a variety of device shapes. An optimization of geometric configuration was made to produce the most desirable device characteristics. Amplification was observed at low frequencies and initial coupling circuit designs were made to enable high frequency measurement. Development of potentially more versatile fabrication techniques using niobium and niobium nitride was also begun, as was a simulation study aimed primarily at understanding spatially nonuniform long junction structures.
Aluminum Josephson junctions are the building blocks for the realization of superconducting quantum bits. Attention has been also paid to hybrid ferromagnetic Josephson junctions, which allow switching between different magnetic states, making them interesting for applications such as cryogenic memories, single-photon detectors, and spintronics. In this paper, we report on the fabrication and characterization of high-quality ferromagnetic Josephson junctions based on aluminum technology. We employed an innovative fabrication process inspired by niobium-based technology, allowing us to obtain very high-quality hybrid aluminum Josephson junctions; thus, supporting the use of ferromagnetic Josephson junctions in advanced quantum circuits. The fabrication process is described in detail and the main DC transport properties at low temperatures (current-voltage characteristic, critical current as a function of the temperature, and the external magnetic field) are reported. Here, we illustrate in detail the fabrication process, as well as the main DC transport properties at low temperatures (current-voltage characteristic, critical current as a function of the temperature, and the external magnetic field).
We have developed a fabrication technique for Josephson junctions that employs a three-dimensional patterned, low-loss substrate instead of commonly used organic resists. The technique enables the fabrication of high-quality trilayer junctions from a wide range of geometries and materials, including high-melting-point superconductors such as tantalum or niobium. The junction electrodes are free from intentionally introduced oxides and organic materials, which are known sources of decoherence. We fabricate and characterize underdamped Nb/AlOx/Nb junctions of different sizes in several geometries.