Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Bulletin of the American Physical Society

Fabrication and Characterization of Aluminum Airbridges for Superconducting Qubit Circuits

Zijun Chen, A. Megrant, J. Kelly, R. Barends, Joerg Bochmann, Yu Chen, Benjamin Chiaro, A. Dunsworth, Evan R. Jeffrey, J. Mutus, P. J. J. O’Malley, Charles Neill, P. Roushan, D. Sank, A. Vainsencher, J. Wenner, T. White, Andrew N. Cleland, John M. Martinis

Published Mar 5, 2014• 0 citations
OpenAlex

Related papers

Fabrication of Airbridges for Superconducting Quantum Circuits

Jharna Paul, Valentino Seferai, Cong Fu +5 more

ENLIGHTEN (Jurnal Bimbingan dan Konseling Islam)•Jul 1, 2023•0 citations

Airbridges for scalable microwave control of superconducting qubits

Michael Fang, Andrew J. Keller, Oskar J. Painter

Bulletin of the American Physical Society•Mar 14, 2017•0 citations

Fabrication and characterization of aluminum airbridges for superconducting microwave circuits

Zijun Chen, A. Megrant, J. Kelly +16 more

Superconducting microwave circuits based on coplanar waveguides (CPW) are susceptible to parasitic slotline modes which can lead to loss and decoherence. We motivate the use of superconducting airbridges as a reliable method for preventing the propagation of these modes. We describe the fabrication of these airbridges on superconducting resonators, which we use to measure the loss due to placing airbridges over CPW lines. We find that the additional loss at single photon levels is small, and decreases at higher drive powers.

arXiv:1310.2325•Applied Physics Letters•Feb 3, 2014•155 citations

Fabrication and characterization of low loss niobium airbridges for superconducting quantum circuits

Hao-Ran Tao, Chi Zhang, Lei Du +8 more

Airbridges are extensively employed in superconducting quantum circuits to suppress parasitic slotline modes in coplanar waveguide and minimize crosstalk between control lines. Here, we introduce a fabrication technique for airbridges, leveraging niobium as the bridge layer and aluminum as the sacrificial layer to preclude the introduction of lossy dielectrics or residues upon release. Additionally, we utilize a triangular evaporation method to significantly bolster the structural integrity of the airbridges. Our experimental evaluation, focused on resonators equipped with these airbridges, reveals that the resultant additional loss per bridge is minimal, quantified at (5.0±2.8)×10−9 in the single-photon regime and (6.3±0.9)×10−9 at high drive powers. This advancement underscores the potential of niobium airbridges in facilitating the development of large-scale and high-performance superconducting quantum circuits.

Applied Physics Letters•Jul 15, 2024•7 citations

Exploration of Alternate Fabrication and Processing Techniques for Superconducting Qubit Junctions

Yebin Liu, JJ Nelson, Jaseung Ku +1 more

Bulletin of the American Physical Society•Mar 9, 2018•0 citations

A method for building low loss multi-layer wiring for superconducting microwave devices

A. Dunsworth, R. Barends, Yu Chen +20 more

Complex integrated circuits require multiple wiring layers. In complementary metal-oxide-semiconductor processing, these layers are robustly separated by amorphous dielectrics. These dielectrics would dominate energy loss in superconducting integrated circuits. Here, we describe a procedure that capitalizes on the structural benefits of inter-layer dielectrics during fabrication and mitigates the added loss. We use a deposited inter-layer dielectric throughout fabrication and then etch it away post-fabrication. This technique is compatible with foundry level processing and can be generalized to make many different forms of low-loss wiring. We use this technique to create freestanding aluminum vacuum gap crossovers (airbridges). We characterize the added capacitive loss of these airbridges by connecting ground planes over microwave frequency λ/4 coplanar waveguide resonators and measuring resonator loss. We measure a low power resonator loss of ∼3.9 × 10−8 per bridge, which is 100 times lower than that of dielectric supported bridges. We further characterize these airbridges as crossovers, control line jumpers, and as part of a coupling network in gmon and fluxmon qubits. We measure qubit characteristic lifetimes (T1s) in excess of 30 μs in gmon devices.

arXiv:1712.01671•Applied Physics Letters•Feb 5, 2018•65 citations
Superconducting microwave circuits based on coplanar waveguides (CPW) are susceptible to parasitic slotline modes which can lead to loss and decoherence. We motivate the use of superconducting airbridges as a reliable method for preventing the propagation of these modes. We describe the fabrication of these airbridges on superconducting resonators, which we use to measure the loss due to placing airbridges over CPW lines. We find that the additional loss at single photon levels is small, and decreases at higher drive powers.
Airbridges are extensively employed in superconducting quantum circuits to suppress parasitic slotline modes in coplanar waveguide and minimize crosstalk between control lines. Here, we introduce a fabrication technique for airbridges, leveraging niobium as the bridge layer and aluminum as the sacrificial layer to preclude the introduction of lossy dielectrics or residues upon release. Additionally, we utilize a triangular evaporation method to significantly bolster the structural integrity of the airbridges. Our experimental evaluation, focused on resonators equipped with these airbridges, reveals that the resultant additional loss per bridge is minimal, quantified at (5.0±2.8)×10−9 in the single-photon regime and (6.3±0.9)×10−9 at high drive powers. This advancement underscores the potential of niobium airbridges in facilitating the development of large-scale and high-performance superconducting quantum circuits.
Complex integrated circuits require multiple wiring layers. In complementary metal-oxide-semiconductor processing, these layers are robustly separated by amorphous dielectrics. These dielectrics would dominate energy loss in superconducting integrated circuits. Here, we describe a procedure that capitalizes on the structural benefits of inter-layer dielectrics during fabrication and mitigates the added loss. We use a deposited inter-layer dielectric throughout fabrication and then etch it away post-fabrication. This technique is compatible with foundry level processing and can be generalized to make many different forms of low-loss wiring. We use this technique to create freestanding aluminum vacuum gap crossovers (airbridges). We characterize the added capacitive loss of these airbridges by connecting ground planes over microwave frequency λ/4 coplanar waveguide resonators and measuring resonator loss. We measure a low power resonator loss of ∼3.9 × 10−8 per bridge, which is 100 times lower than that of dielectric supported bridges. We further characterize these airbridges as crossovers, control line jumpers, and as part of a coupling network in gmon and fluxmon qubits. We measure qubit characteristic lifetimes (T1s) in excess of 30 μs in gmon devices.