Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Fabrication and characterization of low loss niobium airbridges for superconducting quantum circuits

Hao-Ran Tao, Chi Zhang, Lei Du, Xin-Xin Yang, Liang-Liang Guo, Yong Chen, Hai-Feng Zhang, Zhi-Long Jia, Weicheng Kong, Peng Duan, Guo‐Ping Guo

Published Jul 15, 2024• 7 citations
Publisher

Abstract

Airbridges are extensively employed in superconducting quantum circuits to suppress parasitic slotline modes in coplanar waveguide and minimize crosstalk between control lines. Here, we introduce a fabrication technique for airbridges, leveraging niobium as the bridge layer and aluminum as the sacrificial layer to preclude the introduction of lossy dielectrics or residues upon release. Additionally, we utilize a triangular evaporation method to significantly bolster the structural integrity of the airbridges. Our experimental evaluation, focused on resonators equipped with these airbridges, reveals that the resultant additional loss per bridge is minimal, quantified at (5.0±2.8)×10−9 in the single-photon regime and (6.3±0.9)×10−9 at high drive powers. This advancement underscores the potential of niobium airbridges in facilitating the development of large-scale and high-performance superconducting quantum circuits.

DOI
10.1063/5.0216711

Related papers

Fabrication and characterization of aluminum airbridges for superconducting microwave circuits

Zijun Chen, A. Megrant, J. Kelly +16 more

Superconducting microwave circuits based on coplanar waveguides (CPW) are susceptible to parasitic slotline modes which can lead to loss and decoherence. We motivate the use of superconducting airbridges as a reliable method for preventing the propagation of these modes. We describe the fabrication of these airbridges on superconducting resonators, which we use to measure the loss due to placing airbridges over CPW lines. We find that the additional loss at single photon levels is small, and decreases at higher drive powers.

arXiv:1310.2325•Applied Physics Letters•Feb 3, 2014•155 citations

Fabrication of airbridges with gradient exposure

Yuting Sun, Jiayu Ding, Xiaoyu Xia +6 more

In superconducting quantum circuits, airbridges are critical for eliminating parasitic slotline modes of coplanar waveguide circuits and reducing crosstalks between direct current magnetic flux biases. Here, we present a technique for fabricating superconducting airbridges. With this technique, a single layer of photoresist is employed, and the gradient exposure process is used to define the profile of airbridges. In order to properly obtain the bridge profile, we design exposure dosage based on residual photoresist thickness and laser power calibrations. Compared with other airbridge fabrication techniques, the gradient exposure fabrication technique provides the ability to produce lossless superconducting airbridges with flexible size and, thus, is more suitable for large-scale superconducting quantum circuits. Furthermore, this method reduces the complexity of the fabrication process and provides a high fabrication yield.

arXiv:2506.14565•Applied Physics Letters•Aug 15, 2022•16 citations

Niobium air bridges as low-loss components for superconducting quantum hardware

N. Bruckmoser, L. Koch, I. Tsitsilin +12 more

Scaling up superconducting quantum processors necessitates the use of a high routing density for readout and control lines, relying on low-loss interconnects to maintain design flexibility and device performance. We propose and demonstrate a universal subtractive fabrication process for air bridges based on an aluminum hard mask and niobium as the superconducting film. Using this technology, we fabricate superconducting coplanar waveguide resonators incorporating several niobium air bridges in and across their center conductors. Through rigorous cleaning methods, we achieve mean internal quality factors in the single-photon limit exceeding Q int = 8.2 × 10 6 . Notably, the loss per air bridge remains below the detection threshold of the resonators. Due to the larger superconducting energy gap of niobium, compared with conventional aluminum air bridges, our approach enables stable performance at elevated temperatures and magnetic fields, which we experimentally confirm in temperatures up to 3.9 K and in a magnetic field of up to 1.60 T. Additionally, we utilize air bridges to realize low-loss vacuum-gap capacitors and demonstrate their successful integration in transmon qubits by achieving median qubit lifetimes of T 1 = 51.6 μ s .

arXiv:2503.12076•Physical Review Applied•Dec 9, 2025•11 citations

Aluminum Air Bridges for Integrated Superconducting Quantum Circuits

L. Kaczmarek, M. Schmelz, E. Mutsenik +4 more

Superconducting circuits are one of the most promising realizations for quantum technologies especially for quantum computing. Corresponding research must consider both: the quantum bit (so-called qubit) itself, which is often implemented as a transmon-type qubit for large scale applications, and the qubit's on-chip environment. Therein, coplanar waveguide resonators and coplanar transmission lines are mostly used for addressing and reading out the transmons. The coplanar resonators need to have high intrinsic quality factors which significantly depend on the material and the fabrication process. Consequently, a profound knowledge of the fabrication process is mandatory. For an increasing number of qubits on a chip and, thus, more complex circuit designs, beyond 2-D integration technologies are required to suppress unwanted slotline modes due to anharmonicities and discontinuities within the circuits ground planes. Superconducting low-inductance air bridges can ensure this feature by equalizing the ground planes’ potential. The aim of this work is to describe our recent progress in wafer-scale fabrication of beyond 2-D superconducting quantum circuits. We show a combined study of resonator circuits and aluminum air bridges. We discuss our optimized fabrication process for resonator circuits with intrinsic quality factors up to approx.Qi= 2,000,000 at high photon numbers as well as the implementation of air bridges into resonator circuits. Finally, we demonstrate the successful implementation of air bridges in context of open quantum systems.

IEEE Transactions on Applied Superconductivity•Sep 2, 2026•0 citations

A method for building low loss multi-layer wiring for superconducting microwave devices

A. Dunsworth, R. Barends, Yu Chen +20 more

Complex integrated circuits require multiple wiring layers. In complementary metal-oxide-semiconductor processing, these layers are robustly separated by amorphous dielectrics. These dielectrics would dominate energy loss in superconducting integrated circuits. Here, we describe a procedure that capitalizes on the structural benefits of inter-layer dielectrics during fabrication and mitigates the added loss. We use a deposited inter-layer dielectric throughout fabrication and then etch it away post-fabrication. This technique is compatible with foundry level processing and can be generalized to make many different forms of low-loss wiring. We use this technique to create freestanding aluminum vacuum gap crossovers (airbridges). We characterize the added capacitive loss of these airbridges by connecting ground planes over microwave frequency λ/4 coplanar waveguide resonators and measuring resonator loss. We measure a low power resonator loss of ∼3.9 × 10−8 per bridge, which is 100 times lower than that of dielectric supported bridges. We further characterize these airbridges as crossovers, control line jumpers, and as part of a coupling network in gmon and fluxmon qubits. We measure qubit characteristic lifetimes (T1s) in excess of 30 μs in gmon devices.

arXiv:1712.01671•Applied Physics Letters•Feb 5, 2018•65 citations

Contacting Josephson Junctions via Airbridges in Superconducting Circuits

Prakiran Baidya, Momčilo Milosavljević, Murali Krishna Kurmapu +6 more

Superconducting circuit devices require electrical interconnects between different circuit elements on the chip, for which conventional device architectures use a combination of two structural elements: \textit{airbridges} to connect non-adjacent elements in the base layer, and \textit{bandages} to connect the electrodes forming the Josephson junctions to the base layer. Bandages introduce unwanted parasitic material interfaces and increase the manufacturing complexity. Here, we overcome the limitations imposed by \emph{bandages} by establishing \textit{all} electrical interconnects with airbridges of varying size fabricated in a single step. The airbridges show a high yield and mechanical stability over a wide range of sizes from $0.5\,μ\mathrm{m}$ to $4\,μ\mathrm{m}$ in width and from $5\,μ\mathrm{m}$ to $40\,μ\mathrm{m}$ in length, and show low loss when integrated in coplanar waveguide resonators and transmon qubits. Measured relaxation times up to more than $250\,μ\mathrm{s}$ in standard transmon geometries show that the process achieves high coherence while substantially easing and accelerating device fabrication.

quant-pharXiv:2606.06951•Jun 8, 2026•0 citations
Airbridges are extensively employed in superconducting quantum circuits to suppress parasitic slotline modes in coplanar waveguide and minimize crosstalk between control lines. Here, we introduce a fabrication technique for airbridges, leveraging niobium as the bridge layer and aluminum as the sacrificial layer to preclude the introduction of lossy dielectrics or residues upon release. Additionally, we utilize a triangular evaporation method to significantly bolster the structural integrity of the airbridges. Our experimental evaluation, focused on resonators equipped with these airbridges, reveals that the resultant additional loss per bridge is minimal, quantified at (5.0±2.8)×10−9 in the single-photon regime and (6.3±0.9)×10−9 at high drive powers. This advancement underscores the potential of niobium airbridges in facilitating the development of large-scale and high-performance superconducting quantum circuits.
Superconducting microwave circuits based on coplanar waveguides (CPW) are susceptible to parasitic slotline modes which can lead to loss and decoherence. We motivate the use of superconducting airbridges as a reliable method for preventing the propagation of these modes. We describe the fabrication of these airbridges on superconducting resonators, which we use to measure the loss due to placing airbridges over CPW lines. We find that the additional loss at single photon levels is small, and decreases at higher drive powers.
In superconducting quantum circuits, airbridges are critical for eliminating parasitic slotline modes of coplanar waveguide circuits and reducing crosstalks between direct current magnetic flux biases. Here, we present a technique for fabricating superconducting airbridges. With this technique, a single layer of photoresist is employed, and the gradient exposure process is used to define the profile of airbridges. In order to properly obtain the bridge profile, we design exposure dosage based on residual photoresist thickness and laser power calibrations. Compared with other airbridge fabrication techniques, the gradient exposure fabrication technique provides the ability to produce lossless superconducting airbridges with flexible size and, thus, is more suitable for large-scale superconducting quantum circuits. Furthermore, this method reduces the complexity of the fabrication process and provides a high fabrication yield.
Scaling up superconducting quantum processors necessitates the use of a high routing density for readout and control lines, relying on low-loss interconnects to maintain design flexibility and device performance. We propose and demonstrate a universal subtractive fabrication process for air bridges based on an aluminum hard mask and niobium as the superconducting film. Using this technology, we fabricate superconducting coplanar waveguide resonators incorporating several niobium air bridges in and across their center conductors. Through rigorous cleaning methods, we achieve mean internal quality factors in the single-photon limit exceeding Q int = 8.2 × 10 6 . Notably, the loss per air bridge remains below the detection threshold of the resonators. Due to the larger superconducting energy gap of niobium, compared with conventional aluminum air bridges, our approach enables stable performance at elevated temperatures and magnetic fields, which we experimentally confirm in temperatures up to 3.9 K and in a magnetic field of up to 1.60 T. Additionally, we utilize air bridges to realize low-loss vacuum-gap capacitors and demonstrate their successful integration in transmon qubits by achieving median qubit lifetimes of T 1 = 51.6 μ s .
Superconducting circuits are one of the most promising realizations for quantum technologies especially for quantum computing. Corresponding research must consider both: the quantum bit (so-called qubit) itself, which is often implemented as a transmon-type qubit for large scale applications, and the qubit's on-chip environment. Therein, coplanar waveguide resonators and coplanar transmission lines are mostly used for addressing and reading out the transmons. The coplanar resonators need to have high intrinsic quality factors which significantly depend on the material and the fabrication process. Consequently, a profound knowledge of the fabrication process is mandatory. For an increasing number of qubits on a chip and, thus, more complex circuit designs, beyond 2-D integration technologies are required to suppress unwanted slotline modes due to anharmonicities and discontinuities within the circuits ground planes. Superconducting low-inductance air bridges can ensure this feature by equalizing the ground planes’ potential. The aim of this work is to describe our recent progress in wafer-scale fabrication of beyond 2-D superconducting quantum circuits. We show a combined study of resonator circuits and aluminum air bridges. We discuss our optimized fabrication process for resonator circuits with intrinsic quality factors up to approx.Qi= 2,000,000 at high photon numbers as well as the implementation of air bridges into resonator circuits. Finally, we demonstrate the successful implementation of air bridges in context of open quantum systems.
Complex integrated circuits require multiple wiring layers. In complementary metal-oxide-semiconductor processing, these layers are robustly separated by amorphous dielectrics. These dielectrics would dominate energy loss in superconducting integrated circuits. Here, we describe a procedure that capitalizes on the structural benefits of inter-layer dielectrics during fabrication and mitigates the added loss. We use a deposited inter-layer dielectric throughout fabrication and then etch it away post-fabrication. This technique is compatible with foundry level processing and can be generalized to make many different forms of low-loss wiring. We use this technique to create freestanding aluminum vacuum gap crossovers (airbridges). We characterize the added capacitive loss of these airbridges by connecting ground planes over microwave frequency λ/4 coplanar waveguide resonators and measuring resonator loss. We measure a low power resonator loss of ∼3.9 × 10−8 per bridge, which is 100 times lower than that of dielectric supported bridges. We further characterize these airbridges as crossovers, control line jumpers, and as part of a coupling network in gmon and fluxmon qubits. We measure qubit characteristic lifetimes (T1s) in excess of 30 μs in gmon devices.
Superconducting circuit devices require electrical interconnects between different circuit elements on the chip, for which conventional device architectures use a combination of two structural elements: \textit{airbridges} to connect non-adjacent elements in the base layer, and \textit{bandages} to connect the electrodes forming the Josephson junctions to the base layer. Bandages introduce unwanted parasitic material interfaces and increase the manufacturing complexity. Here, we overcome the limitations imposed by \emph{bandages} by establishing \textit{all} electrical interconnects with airbridges of varying size fabricated in a single step. The airbridges show a high yield and mechanical stability over a wide range of sizes from 0.5 μm0.5\,μ\mathrm{m}0.5μm to 4 μm4\,μ\mathrm{m}4μm in width and from 5 μm5\,μ\mathrm{m}5μm to 40 μm40\,μ\mathrm{m}40μm in length, and show low loss when integrated in coplanar waveguide resonators and transmon qubits. Measured relaxation times up to more than 250 μs250\,μ\mathrm{s}250μs in standard transmon geometries show that the process achieves high coherence while substantially easing and accelerating device fabrication.