Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physica C Superconductivity

Statistical analysis of error rate of large-scale single flux quantum logic circuit by considering fluctuation of timing parameters

Yuki Yamanashi, Kota Masubuchi, Nobuyuki Yoshikawa

Published Mar 8, 2016• 3 citations
Publisher
DOI
10.1016/j.physc.2016.03.001

Related papers

Measurement of Bit-Error-Rate of Single Flux Quantum Logic gates with optimized Josephson Comparator structure

Asakura Kenta

The Japan Society of Applied Physics•Feb 6, 2015•0 citations

Development of an Optimization Tool for RSFQ Digital Cell Library Using Particle Swarm

Y. Tukel, Ali Bozbey, C.A. Tunc

Successful fabrication and demonstration of complex Rapid Single Flux Quantum (RSFQ) circuits depend heavily on the reliability of the cell library that is used for the design. In large-scale RSFQ integrated circuits, delay fluctuations (jitter) of each cell may occur due to fabrication tolerances. The fabrication-induced jitter of each cell might accumulate at each stage and bring out larger variations comparable with the designed delay. If such jitter is not considered while arranging timing of the circuit, it may cause the circuit to malfunction due to the shifting of SFQ pulses. Therefore, it is important to optimize and determine the delay fluctuations of each cell well before designing a large-scale integrated circuit. There are quite a number of parameters that affect the functioning and the performance of a logic gate; hence, an optimization tool is required. In this study, the progress on development of an optimization tool for a digital RSFQ cell library composed of fundamental logic gates, such as Josephson transmission lines, D-flip-flops, T-Flip-flops, splitters, and mergers are presented. Particle swarm optimization is used for an optimization algorithm, which determines the circuit parameters with minimum delay and/or jitter satisfying the required critical margin conditions.

IEEE Transactions on Applied Superconductivity•Dec 12, 2012•20 citations

Timing verification of rapid single flux quantum logic cell

Bicong Weng, Xiaoping Gao, Jie Ren +4 more

Physica C Superconductivity•May 24, 2023•3 citations

The Relationship Between Bit-Error Rate, Operating Speed and Circuit Scale of SFQ Circuits

Hirotaka Terai, Y. Hashimoto, Shinichi Yorozu +3 more

Timing jitter is an important constraint for the performance of SFQ circuits. We focus on the timing jitter in a Josephson transmission line (JTL) that induces timing errors at logic gates. A proper data analysis of 2-bit shift registers gave a jitter value of about 0.08 ps for a single Josephson junction in a JTL powered at a designed bias current. The variations in timing parameters of logic cells also give rise to timing errors. We experimentally determined the timing parameters in several logic cells and found that the deviations between actual and nominal values are within 2 ps. The relationship between the gray zone and circuit scale was estimated by extrapolating the transition curves observed in 2-bit shift registers. The estimated circuit scale was 20,000-100,000 JJs and 1,000 JJs at an operating clock frequency of 20 GHz and 40 GHz, respectively.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•13 citations

Investigate of Influence of Thermal Noise on Single Flux Quantum Logic Gate

Kota Masubuchi

The Japan Society of Applied Physics•Jul 8, 2014•0 citations

Bit error rate determination of RSFQ logic cells by means of noise analysis of basic network components

Thomas Ortlepp, Hannes Toepfer, Friedrich Uhlmann

The influence of thermal noise gives a major restriction in the development of Rapid Single Flux Quantum (RSFQ) logic circuits with high-T/sub c/ superconductors. In the past, we have demonstrated a general way for determining the digital bit error rate and for predicting operation ranges with good noise immunity. The method is based on a single Fokker-Planck equation which includes the full system dynamics. However, the complexity of this equation increases dramatically with the number of Josephson junctions. Our new approach describes a method to divide an RSFQ logic cell into several basic primitives. They can be characterized quickly in terms of switching probability for a lot of different parameters. From these analyses, look-up tables are built-up. We describe how to combine these data in order to achieve the bit-error rate for the whole cell. While saving more than 90% of computation time, the comparison with our previous results for full system analyses shows less than 4% difference. This approach provides for a powerful tool to include the influence of thermal noise into the optimization process of RSFQ logic circuits as well.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•3 citations
Successful fabrication and demonstration of complex Rapid Single Flux Quantum (RSFQ) circuits depend heavily on the reliability of the cell library that is used for the design. In large-scale RSFQ integrated circuits, delay fluctuations (jitter) of each cell may occur due to fabrication tolerances. The fabrication-induced jitter of each cell might accumulate at each stage and bring out larger variations comparable with the designed delay. If such jitter is not considered while arranging timing of the circuit, it may cause the circuit to malfunction due to the shifting of SFQ pulses. Therefore, it is important to optimize and determine the delay fluctuations of each cell well before designing a large-scale integrated circuit. There are quite a number of parameters that affect the functioning and the performance of a logic gate; hence, an optimization tool is required. In this study, the progress on development of an optimization tool for a digital RSFQ cell library composed of fundamental logic gates, such as Josephson transmission lines, D-flip-flops, T-Flip-flops, splitters, and mergers are presented. Particle swarm optimization is used for an optimization algorithm, which determines the circuit parameters with minimum delay and/or jitter satisfying the required critical margin conditions.
Timing jitter is an important constraint for the performance of SFQ circuits. We focus on the timing jitter in a Josephson transmission line (JTL) that induces timing errors at logic gates. A proper data analysis of 2-bit shift registers gave a jitter value of about 0.08 ps for a single Josephson junction in a JTL powered at a designed bias current. The variations in timing parameters of logic cells also give rise to timing errors. We experimentally determined the timing parameters in several logic cells and found that the deviations between actual and nominal values are within 2 ps. The relationship between the gray zone and circuit scale was estimated by extrapolating the transition curves observed in 2-bit shift registers. The estimated circuit scale was 20,000-100,000 JJs and 1,000 JJs at an operating clock frequency of 20 GHz and 40 GHz, respectively.
The influence of thermal noise gives a major restriction in the development of Rapid Single Flux Quantum (RSFQ) logic circuits with high-T/sub c/ superconductors. In the past, we have demonstrated a general way for determining the digital bit error rate and for predicting operation ranges with good noise immunity. The method is based on a single Fokker-Planck equation which includes the full system dynamics. However, the complexity of this equation increases dramatically with the number of Josephson junctions. Our new approach describes a method to divide an RSFQ logic cell into several basic primitives. They can be characterized quickly in terms of switching probability for a lot of different parameters. From these analyses, look-up tables are built-up. We describe how to combine these data in order to achieve the bit-error rate for the whole cell. While saving more than 90% of computation time, the comparison with our previous results for full system analyses shows less than 4% difference. This approach provides for a powerful tool to include the influence of thermal noise into the optimization process of RSFQ logic circuits as well.