Successful fabrication and demonstration of complex Rapid Single Flux Quantum (RSFQ) circuits depend heavily on the reliability of the cell library that is used for the design. In large-scale RSFQ integrated circuits, delay fluctuations (jitter) of each cell may occur due to fabrication tolerances. The fabrication-induced jitter of each cell might accumulate at each stage and bring out larger variations comparable with the designed delay. If such jitter is not considered while arranging timing of the circuit, it may cause the circuit to malfunction due to the shifting of SFQ pulses. Therefore, it is important to optimize and determine the delay fluctuations of each cell well before designing a large-scale integrated circuit. There are quite a number of parameters that affect the functioning and the performance of a logic gate; hence, an optimization tool is required. In this study, the progress on development of an optimization tool for a digital RSFQ cell library composed of fundamental logic gates, such as Josephson transmission lines, D-flip-flops, T-Flip-flops, splitters, and mergers are presented. Particle swarm optimization is used for an optimization algorithm, which determines the circuit parameters with minimum delay and/or jitter satisfying the required critical margin conditions.
Successful fabrication and demonstration of complex Rapid Single Flux Quantum (RSFQ) circuits depend heavily on the reliability of the cell library that is used for the design. In large-scale RSFQ integrated circuits, delay fluctuations (jitter) of each cell may occur due to fabrication tolerances. The fabrication-induced jitter of each cell might accumulate at each stage and bring out larger variations comparable with the designed delay. If such jitter is not considered while arranging timing of the circuit, it may cause the circuit to malfunction due to the shifting of SFQ pulses. Therefore, it is important to optimize and determine the delay fluctuations of each cell well before designing a large-scale integrated circuit. There are quite a number of parameters that affect the functioning and the performance of a logic gate; hence, an optimization tool is required. In this study, the progress on development of an optimization tool for a digital RSFQ cell library composed of fundamental logic gates, such as Josephson transmission lines, D-flip-flops, T-Flip-flops, splitters, and mergers are presented. Particle swarm optimization is used for an optimization algorithm, which determines the circuit parameters with minimum delay and/or jitter satisfying the required critical margin conditions.
ENGLISH ABSTRACT: Rapid Single Flux Quantum (RSFQ) cells are key in the design of complex and applicable RSFQ electronic circuits. These cells are low-level circuit elements that are used repeatedly to build larger, applicable RSFQ circuitry. Making these cells simple to layout and manufacture, but reliable for extensive use demands a careful development process for RSFQ cells. Cell functionality is verified through simulations, thereafter the cell is laid out in special software packages. Inductance of on-chip superconductor structures is extracted through careful modelling with numerical field solver software. A cell library has been developed by incorporating existing or published cells after further analysis and optimization, as well as developing new cells. Cells that have been adapted into the library include the Josephson transmission line (JTL), Splitter, Merger, D-Flip Flop (DFF), T-Flip Flop (TFF), NOT, AND, OR and XOR, DC-SFQ and SFQ-DC and PTL Driver and Receivers. New cells include NOR, NAND and XNOR. The cells were designed for the IPHT’s RSFQ1D 1kA/cmª and Hypres’ 4.5kA/cmª processes. The cells in the library have good bias current operating margins obtained through simulations (> ±26%). All cells have all the parameters listed in the thesis including extracted inductance values. In order to have a complete and verified RSFQ cell library, cells have been sent for fabrication at IPHT and Hypres facilities. These cells can now be tested on-chip, in the laboratory, to establish functionality and practical bias current margins. All test signal patterns and bias currents required for testing are defined to allow co-workers or collaborators to test the cells.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
We have developed a cell library for superconducting large scale integrated (LSI) digital circuits based on Single Flux Quantum (SFQ) devices. The circuits were designed for a 6-kA/cm2Nb/AlOx/Nb junction process with 10 mask levels including one ground plane and two Nb wiring layers. The initial design and optimization of the circuit parameters were achieved by means of the optimization functions in a circuit simulator, PSCAN2, to ensure that important circuit parameters, Josephson critical current (IC), bias current (Ibias), and inductance satisfied minimal margin requirements. Critical margins of ICand Ibiaswere then further improved manually. To compensate the scattering in the circuit parameters from fabrication by design as much as possible, the critical junction parameters were optimized to further centralize the IC. The library cells were laid out following our design rules determined by systematic experiments on process control monitors (PCM). Basic cells including Josephson transmission lines, splitters, confluence buffers, D flip-flops, T flip-flops, and XOR and NDRO gates were designed, fabricated, and successfully tested at low frequencies. Wide overlaps of the operating regions for the common bias voltages were confirmed.
Rapid single flux quantum technology is one of the most promising developments for future high-speed microprocessors, network routers, and analog-to-digital converters. This technology is based on well-timed signals and fast signal transmission. However, as the complexity of the circuits or the operating frequency of these signals increase, it becomes harder to achieve a successful timing scheme. Another case that prevents successful timing is thermal noise, which becomes more significant with the increase of the number of cells. Earlier studies on noise analysis show that the timing variations of the delay on a cascaded path vary up to 10% compared with the delay of the same type of single cell. On the other hand, circuit parameters may change during the fabrication process, and as a result, timing of the cell differs from the design value. For these reasons, we define a statistical model for the wiring cells, such as Josephson transmission lines, splitters, and mergers that can be used to calculate the timing delay and jitter instead of time-consuming simulations. We also discuss a possible method to identify the sensitive paths to the delay fluctuations among different alternatives. In this study, we analyze the delay and the jitter of cascaded combinations of the most common wiring cells to determine the correlation effect on delay and jitter between the consecutive gates. Then, we propose a statistical method to analyze these timings faster and easier. Finally, we discussed how to estimate the output probability of the clocked gates without performing an actual simulation.
At the typical operating temperature of 4.2 K, the theoretical upper limit of the clock frequency of the Low-Temperature Superconductive (LTS) Nb based Rapid Single Flux Quantum (RSFQ) digital circuits is several hundred GHz. Nevertheless, the few middle-scale RSFQ circuits reported on up to now operate at only some tens of GHz. An important performance-limiting factor is in this case the clock signal distribution, so nowadays asynchronous RSFQ designs are often considered. Our previous studies have shown that it is an important advantage of a given asynchronous RSFQ cell library to contain gates with tunable delays. We have already shown by simulations that the RSFQ gate delays are best adjusted by changing the Stewart-McCumber parameter /spl beta//sub c/ of the Josephson junctions-this method tunes the delay within a large interval of values while scarcely affecting the margins and the fabrication yield of the RSFQ gates. In order to prove this statement experimentally, we have designed, fabricated, and tested several ring-shaped oscillators with identical topologies but different Stewart-McCumber parameters of the Josephson junctions. Their operating speeds and margins are measured and compared.
Rapid single flux quantum (RSFQ) digital circuits have reached the level of medium- to large-scale of integration. At this level, existing design methodologies, developed specifically for RSFQ circuits, have become computationally inefficient. Applying mature semiconductor methodologies to the design of RSFQ circuits, one encounters substantial difficulties originating from the differences between both technologies. In this paper, a new design methodology aimed at large-scale RSFQ circuits is proposed. This methodology is based on a semiconductor semicustom design approach. An established design methodology for small-stale RSFQ digital circuits, based on circuit (junction-level) simulation and device parameter optimization, is used for the design of basic RSFQ cells. A library composed of about 20 basic RSFQ cells has been developed based on this approach. A novel design methodology for large-scale circuits, presented in this paper, is based on logic (gate-level) simulation and timing optimization. This methodology has been implemented around the Cadence integrated design environment and used successfully at the University of Rochester for the design of two large-scale digital circuits.