Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Superconductive Electronics Conference (ISEC)

Characterization of NbTiN Films for Superconducting Terahertz Circuitry

Yoshinori Uzawa, Kazumasa Makise, Shingo Saito, Hirotaka Terai, Z. Wang, Takafumi Kojima, M. Kroug, Y. Fujii, Álvaro González, Keiko Kaneko

Published Jul 1, 2015• 1 citation
Publisher

Abstract

We have investigated superconducting properties of niobium titanium nitride (NbTiN) films to be used for the lower and upper electrodes of a microstrip line with a SiO2insulator on a quartz substrate at Terahertz frequencies. NbTiN films were prepared on a 1-mm thick quartz substrate directly (assumed to be the lower electrode of the microstrip line) and on an about 150-nm thick SiO2layer sputtered on a quartz substrate (assumed to be the upper electrode) by reactive dc magnetron sputtering at ambient temperature. The complex conductivity measurement by Terahertz time- domain spectroscopy revealed that both films have similar superconducting properties with critical temperatures of about 14 K and gap frequencies of about 1.2 THz at 5 K. This indicates that all-NbTiN microstrip lines may work well as extremely low-loss transmission lines at Terahertz frequencies.

DOI
10.1109/isec.2015.7383432

Related papers

Contactless terahertz mapping of wafer-scale superconducting NbTiN thin films

Yayi Lin, Marc Neis, Marcello P. Guardascione +9 more

For large-scale superconducting quantum technology, e.g. quantum computing, the homogeneity of wafer-scale superconducting thin films is vital for consistent performance of the fabricated devices. Terahertz (THz) spectroscopy as a contactless and non-destructive measurement technique is a powerful tool to characterize the superconducting films. In this work, a set of niobium titanium nitride (NbTiN) thin films on 4-inch and 6-inch silicon wafers, grown via plasma-enhanced magnetron sputtering, are investigated via THz spectroscopy: full wafers are mapped at room temperatures and exemplary segments are characterized at cryogenic temperatures. The deviations in observed sheet resistance depend on the used deposition device and the film thickness. While the deviations in superconducting sheet kinetic inductance match those of the normal-state sheet resistance, the critical temperature and energy gap exhibit little variation. This THz mapping technique demonstrates the feasibility of evaluating wafer-scale superconducting thin films before lithography, facilitating preparation of the thin films for reproducible device fabrication.

arXiv:2607.15757•Jul 17, 2026•0 citations

Impact of the Buffer Layers and Anodization on Properties of NbTiN Films for THz Receivers

Elena S. Zhukova, Boris P. Gorshunov, Lenar S. Kadyrov +7 more

In this paper, we present the results of the research aimed at improving the fabrication process of a SIS-mixer for operation at frequencies close to 1 THz. We study the impact of buffer aluminum oxide layer and anodization effects on the properties of superconducting NbTiN films which form the electrodes of the transmission lines in THz-range devices. These layers are traditionally used in technological processes. The measurements of THz response are performed using terahertz time-domain spectrometer at frequencies from 0.3 to 2.0 THz. It was found that the critical temperature, normal-state conductivity just above the transition temperature, superconducting gap value and London penetration depth of the NbTiN film sputtered on aluminum oxide buffer layer are almost the same as of the film sputtered directly onto the substrate. The difference between the parameters is comparable to the measurement uncertainty for NbTiN films with and without additional surface layers of aluminum and anodization.

IEEE Transactions on Applied Superconductivity•Jan 16, 2024•2 citations

Design of Terahertz SIS Mixers Using Nb/AlN/Nb Junctions Integrated With All-NbTiN Tuning Circuits

Yoshinori Uzawa, M. Kroug, Takafumi Kojima +7 more

We have designed superconductor-insulator-superconductor (SIS) mixers using Nb/AlN/Nb tunnel junctions integrated with NbTiN/SiO2/NbTiN microstrip tuning circuits for the Atacama Large Millimeter/submillimeter Array (ALMA) Band 10 (0.78-0.95 THz). In order to design the tuning circuits, we used terahertz time domain spectroscopy to experimentally derive the complex conductivity of relatively thick NbTiN films deposited on quartz substrate directly as a ground plane and on RF-sputtered SiO2as a microstrip. Results showed that the conductivities of both films can be described by a modified Mattis-Bardeen theory. We also investigated the junction heating effects originating from quasi-particle trapping in the Nb electrodes embedded in NbTiN circuits by varying the volume of the electrodes. It was confirmed that current-voltage curves of Nb/AlN/Nb tunnel junctions with thick (~200 nm) counter electrodes contacting NbTiN wirings showed higher gap voltages as well as reduced back-bending than those with thin (~50 nm) electrodes. Making use of these findings, our designed SIS mixers employing Nb/AlN/Nb junctions with a current density of 15 kA/cm2and all-NbTiN tuning circuits may cover the Band 10 with good sensitivity.

IEEE Transactions on Applied Superconductivity•Nov 28, 2016•12 citations

Dispersive Spectrometry At Terahertz Frequencies for Probing the Quality of NbTiN Superconducting Films

Andrey V. Khudchenko, Bram Lap, Kirill I. Rudakov +9 more

We present the quality measurements of thick (thicker than London penetration depth) NbTiN superconducting films at Terahertz frequencies using a Dispersive Fourier Transform Spectrometer (DFTS). The reflected RF signal from the tested film was measured in time domain, allowing us to separate it from other reflections. The complex conductivity of the film depends on frequency and determines the reflection coefficient. By comparing the film reflection in superconducting state (film temperature below$Tc$) with that of the normal state (film temperature above$Tc$), we characterized the film quality at terahertz frequencies, and directly probed the energy of the superconducting gap of the tested film. The experimental results were fitted using the extended Mattis-Bardeen theory and th obtained film parameters show a good agreement with the literature. In addition to the DFTS, we have also measured the properties of NbTiN film using Time Domain Spectroscopy (TDS). It is shown that both TDS and DFTS provide similar results, and both techniques can be used for the quality control of thick NbTiN films. The superconducting gap determined from the measurements by both DFTS and TDS are in good agreement for both solid and meshed films showing that there is no remarkable degradation in the film quality due to technological processes of lift-off or ion etching.

IEEE Transactions on Applied Superconductivity•Feb 1, 2022•6 citations

Development of 1.5 THz waveguide NbTiN superconducting hot electron bolometer mixers

Ling Jiang, Shoichi Shiba, Tatsuya Shiino +7 more

We present a characterization of a 1.5 THz waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixer which can be pumped by a commercial solid state tunable local oscillator (LO) source. The NbTiN HEB mixer is made from a 12 nm thick NbTiN thin film deposited on a quartz substrate at room temperature. A gold electrode is formed in situ on the NbTiN thin film without breaking vacuum to ensure good contact. The uncorrected DSB receiver noise temperature is measured to be 1700 K at 1.5 THz, whereas the mixer noise temperature is derived to be 1000 K after corrections for losses of the input optics and the intermediate frequency (IF) amplifier chain. The required LO power absorbed in the HEB mixer is evaluated to be 340 nW by using an isothermal technique. The IF gain bandwidth is supposed to be about 1.3 GHz or higher. The present results show that good performance can be obtained at 1.5 THz even with a relatively thick NbTiN film (12 nm), as in the case of 0.8 THz. In order to investigate the cooling mechanism of our HEB mixers, we have conducted performance measurements for a few HEB mixers with different microbridge sizes both at 1.5 and 0.8 THz. The noise performance of the NbTiN HEB mixers is found to depend on the length of the NbTiN microbridge. The shorter the microbridge is, the lower the receiver noise temperature is. This may imply a contribution of the diffusion cooling in addition to the phonon cooling.

Superconductor Science and Technology•Mar 19, 2010•21 citations

Development of THz Waveguide NbTiN HEB Mixers

Ling Jiang, S. Shiba, K. Shimbo +7 more

In this paper, we present the development of the waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixers, cryogenically cooled by a 4 K close-cycled refrigerator. The NbTiN thin film is formed on a crystalline quartz substrate by sputtering an NbTi target with the Ar and N2gas at room temperature. The HEB mixer element is fabricated by using the 12 nm NbTiN film, and is mounted on a waveguide block. Measurement of a Fourier transform spectrometer shows that the response of the mixer is centered near 810 GHz with a bandwidth of about 500 GHz. The uncorrected DSB receiver noise temperature is measured to be 500 K, and the noise bandwidth is to be 1.4 GHz at 810 GHz. The present result shows that a good noise performance can be obtained for the NbTiN HEB mixer even with a relatively thick film (12 nm) fabricated at the room temperature.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•16 citations
We have investigated superconducting properties of niobium titanium nitride (NbTiN) films to be used for the lower and upper electrodes of a microstrip line with a SiO2insulator on a quartz substrate at Terahertz frequencies. NbTiN films were prepared on a 1-mm thick quartz substrate directly (assumed to be the lower electrode of the microstrip line) and on an about 150-nm thick SiO2layer sputtered on a quartz substrate (assumed to be the upper electrode) by reactive dc magnetron sputtering at ambient temperature. The complex conductivity measurement by Terahertz time- domain spectroscopy revealed that both films have similar superconducting properties with critical temperatures of about 14 K and gap frequencies of about 1.2 THz at 5 K. This indicates that all-NbTiN microstrip lines may work well as extremely low-loss transmission lines at Terahertz frequencies.
For large-scale superconducting quantum technology, e.g. quantum computing, the homogeneity of wafer-scale superconducting thin films is vital for consistent performance of the fabricated devices. Terahertz (THz) spectroscopy as a contactless and non-destructive measurement technique is a powerful tool to characterize the superconducting films. In this work, a set of niobium titanium nitride (NbTiN) thin films on 4-inch and 6-inch silicon wafers, grown via plasma-enhanced magnetron sputtering, are investigated via THz spectroscopy: full wafers are mapped at room temperatures and exemplary segments are characterized at cryogenic temperatures. The deviations in observed sheet resistance depend on the used deposition device and the film thickness. While the deviations in superconducting sheet kinetic inductance match those of the normal-state sheet resistance, the critical temperature and energy gap exhibit little variation. This THz mapping technique demonstrates the feasibility of evaluating wafer-scale superconducting thin films before lithography, facilitating preparation of the thin films for reproducible device fabrication.
In this paper, we present the results of the research aimed at improving the fabrication process of a SIS-mixer for operation at frequencies close to 1 THz. We study the impact of buffer aluminum oxide layer and anodization effects on the properties of superconducting NbTiN films which form the electrodes of the transmission lines in THz-range devices. These layers are traditionally used in technological processes. The measurements of THz response are performed using terahertz time-domain spectrometer at frequencies from 0.3 to 2.0 THz. It was found that the critical temperature, normal-state conductivity just above the transition temperature, superconducting gap value and London penetration depth of the NbTiN film sputtered on aluminum oxide buffer layer are almost the same as of the film sputtered directly onto the substrate. The difference between the parameters is comparable to the measurement uncertainty for NbTiN films with and without additional surface layers of aluminum and anodization.
We have designed superconductor-insulator-superconductor (SIS) mixers using Nb/AlN/Nb tunnel junctions integrated with NbTiN/SiO2/NbTiN microstrip tuning circuits for the Atacama Large Millimeter/submillimeter Array (ALMA) Band 10 (0.78-0.95 THz). In order to design the tuning circuits, we used terahertz time domain spectroscopy to experimentally derive the complex conductivity of relatively thick NbTiN films deposited on quartz substrate directly as a ground plane and on RF-sputtered SiO2as a microstrip. Results showed that the conductivities of both films can be described by a modified Mattis-Bardeen theory. We also investigated the junction heating effects originating from quasi-particle trapping in the Nb electrodes embedded in NbTiN circuits by varying the volume of the electrodes. It was confirmed that current-voltage curves of Nb/AlN/Nb tunnel junctions with thick (~200 nm) counter electrodes contacting NbTiN wirings showed higher gap voltages as well as reduced back-bending than those with thin (~50 nm) electrodes. Making use of these findings, our designed SIS mixers employing Nb/AlN/Nb junctions with a current density of 15 kA/cm2and all-NbTiN tuning circuits may cover the Band 10 with good sensitivity.
We present the quality measurements of thick (thicker than London penetration depth) NbTiN superconducting films at Terahertz frequencies using a Dispersive Fourier Transform Spectrometer (DFTS). The reflected RF signal from the tested film was measured in time domain, allowing us to separate it from other reflections. The complex conductivity of the film depends on frequency and determines the reflection coefficient. By comparing the film reflection in superconducting state (film temperature belowTcTcTc) with that of the normal state (film temperature aboveTcTcTc), we characterized the film quality at terahertz frequencies, and directly probed the energy of the superconducting gap of the tested film. The experimental results were fitted using the extended Mattis-Bardeen theory and th obtained film parameters show a good agreement with the literature. In addition to the DFTS, we have also measured the properties of NbTiN film using Time Domain Spectroscopy (TDS). It is shown that both TDS and DFTS provide similar results, and both techniques can be used for the quality control of thick NbTiN films. The superconducting gap determined from the measurements by both DFTS and TDS are in good agreement for both solid and meshed films showing that there is no remarkable degradation in the film quality due to technological processes of lift-off or ion etching.
We present a characterization of a 1.5 THz waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixer which can be pumped by a commercial solid state tunable local oscillator (LO) source. The NbTiN HEB mixer is made from a 12 nm thick NbTiN thin film deposited on a quartz substrate at room temperature. A gold electrode is formed in situ on the NbTiN thin film without breaking vacuum to ensure good contact. The uncorrected DSB receiver noise temperature is measured to be 1700 K at 1.5 THz, whereas the mixer noise temperature is derived to be 1000 K after corrections for losses of the input optics and the intermediate frequency (IF) amplifier chain. The required LO power absorbed in the HEB mixer is evaluated to be 340 nW by using an isothermal technique. The IF gain bandwidth is supposed to be about 1.3 GHz or higher. The present results show that good performance can be obtained at 1.5 THz even with a relatively thick NbTiN film (12 nm), as in the case of 0.8 THz. In order to investigate the cooling mechanism of our HEB mixers, we have conducted performance measurements for a few HEB mixers with different microbridge sizes both at 1.5 and 0.8 THz. The noise performance of the NbTiN HEB mixers is found to depend on the length of the NbTiN microbridge. The shorter the microbridge is, the lower the receiver noise temperature is. This may imply a contribution of the diffusion cooling in addition to the phonon cooling.
In this paper, we present the development of the waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixers, cryogenically cooled by a 4 K close-cycled refrigerator. The NbTiN thin film is formed on a crystalline quartz substrate by sputtering an NbTi target with the Ar and N2gas at room temperature. The HEB mixer element is fabricated by using the 12 nm NbTiN film, and is mounted on a waveguide block. Measurement of a Fourier transform spectrometer shows that the response of the mixer is centered near 810 GHz with a bandwidth of about 500 GHz. The uncorrected DSB receiver noise temperature is measured to be 500 K, and the noise bandwidth is to be 1.4 GHz at 810 GHz. The present result shows that a good noise performance can be obtained for the NbTiN HEB mixer even with a relatively thick film (12 nm) fabricated at the room temperature.