Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2607.15757

Contactless terahertz mapping of wafer-scale superconducting NbTiN thin films

Yayi Lin, Marc Neis, Marcello P. Guardascione, Janine Lorenz, Thomas J. Smart, Frank Stefan Tautz, Felix Lüpke, Frederik Bolle, Martin Dressel, R. Barends, Pavel A. Bushev, Marc Scheffler

Published Jul 17, 2026• 0 citations
arXivHTMLPDF

Abstract

For large-scale superconducting quantum technology, e.g. quantum computing, the homogeneity of wafer-scale superconducting thin films is vital for consistent performance of the fabricated devices. Terahertz (THz) spectroscopy as a contactless and non-destructive measurement technique is a powerful tool to characterize the superconducting films. In this work, a set of niobium titanium nitride (NbTiN) thin films on 4-inch and 6-inch silicon wafers, grown via plasma-enhanced magnetron sputtering, are investigated via THz spectroscopy: full wafers are mapped at room temperatures and exemplary segments are characterized at cryogenic temperatures. The deviations in observed sheet resistance depend on the used deposition device and the film thickness. While the deviations in superconducting sheet kinetic inductance match those of the normal-state sheet resistance, the critical temperature and energy gap exhibit little variation. This THz mapping technique demonstrates the feasibility of evaluating wafer-scale superconducting thin films before lithography, facilitating preparation of the thin films for reproducible device fabrication.

DOI
10.48550/arxiv.2607.15757

Related papers

Characterization of NbTiN Films for Superconducting Terahertz Circuitry

Yoshinori Uzawa, Kazumasa Makise, Shingo Saito +7 more

We have investigated superconducting properties of niobium titanium nitride (NbTiN) films to be used for the lower and upper electrodes of a microstrip line with a SiO2insulator on a quartz substrate at Terahertz frequencies. NbTiN films were prepared on a 1-mm thick quartz substrate directly (assumed to be the lower electrode of the microstrip line) and on an about 150-nm thick SiO2layer sputtered on a quartz substrate (assumed to be the upper electrode) by reactive dc magnetron sputtering at ambient temperature. The complex conductivity measurement by Terahertz time- domain spectroscopy revealed that both films have similar superconducting properties with critical temperatures of about 14 K and gap frequencies of about 1.2 THz at 5 K. This indicates that all-NbTiN microstrip lines may work well as extremely low-loss transmission lines at Terahertz frequencies.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•1 citation

Development of ultrathin niobium nitride and niobium titanium nitride films for THz hot-electron bolometers

S. Bedorf

The main focus of this work is the development of ultrathin NbN and NbTiN films. A reproducible and reliable deposition process for ultrathin NbN and NbTiN films for the use in phonon-cooled HEB devices was established. The ultrathin films were deposited on silicon (Si) substrates and on 2æm Si3N4 membranes by DC reactive magnetron sputtering. A method for the precise control of the nitrogen partial pressure by monitoring the target voltage has been introduced to deposit high quality, ultrathin NbN (3-4nm, Tc=8.5 K) and NbTiN (4-5nm, Tc=8K) films. Substrate heating of at least 600ʿC during the deposition is essential for the fabrication of ultrathin NbN and NbTiN films on Si substrates and Si3N4 membranes. The fabrication process required for HEB devices to be used in a quasi-optical mixer was developed. The ultrathin film was patterned by electron beam lithography (EBL), resulting in bolometer devices that measure areas of about 0.4 æm x 4 æm. The nature of the contact determines the interface transparency between the bolometer and the contact structure. Different cleaning processes have been performed and the influence on the contact resistance has been instigated. A better interface transparency gives less RF losses and could improve the HEB sensitivity and local oscillator (LO) requirement ...

•Jan 1, 2005•4 citations

Development of THz Waveguide NbTiN HEB Mixers

Ling Jiang, S. Shiba, K. Shimbo +7 more

In this paper, we present the development of the waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixers, cryogenically cooled by a 4 K close-cycled refrigerator. The NbTiN thin film is formed on a crystalline quartz substrate by sputtering an NbTi target with the Ar and N2gas at room temperature. The HEB mixer element is fabricated by using the 12 nm NbTiN film, and is mounted on a waveguide block. Measurement of a Fourier transform spectrometer shows that the response of the mixer is centered near 810 GHz with a bandwidth of about 500 GHz. The uncorrected DSB receiver noise temperature is measured to be 500 K, and the noise bandwidth is to be 1.4 GHz at 810 GHz. The present result shows that a good noise performance can be obtained for the NbTiN HEB mixer even with a relatively thick film (12 nm) fabricated at the room temperature.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•16 citations

High-uniformity atomic layer deposition of superconducting niobium nitride thin films for quantum photonic integration

Ciaran T. Lennon, Yi Shu, J C Brennan +6 more

Abstract Atomic layer deposition (ALD) has been identified as a promising growth method for high-uniformity superconducting thin films for superconducting quantum photonic applications, offering superior uniformity, thickness control and conformality to techniques such as reactive sputtering. The potential scalability of ALD makes this method especially appealing for fabrication of superconducting nanowires and resonators across large areas. We report on the growth of highly uniform superconducting NbN thin films via plasma-enhanced atomic layer deposition (PEALD) with radio frequency substrate biasing, on a 200 mm (8 inch) Si wafer, specifically for superconducting nanowire single-photon detector applications. Niobium nitride films were grown using (tert-butylimido)-tris(diethylamido)-niobium(V) precursor and an H 2 /Ar plasma. The superconducting properties of a variable thickness series of films (5.9–29.8 nm) show critical temperature ( T c ) of 13.5 K approaching bulk thickness (28.8 nm) with low suppression down to the ultrathin regime (5.9 nm), with T c = 10.2 K. T c across the 200 mm wafer with 8 nm thick NbN, measured in 15 mm intervals, exhibits minimal variation (<7%). Microbridge structures fabricated on 8 nm thick NbN films also exhibit high critical current densities ( J c ), > 10 MA cm −2 at 2.6 K. PEALD could therefore be a pivotal technique in enabling large-scale fabrication of integrated quantum photonic devices across a variety of applications.

Materials for Quantum Technology•Nov 8, 2023•16 citations

Growth of titanium-nitride thin films for low-loss superconducting quantum circuits

Gustaf Olson

This is a study of the growth of titanium-nitride (TiN) by plasma assisted molecular beam epitaxy (MBE) for applications in low loss quantum circuits. Titanium nitride is a material known to have low loss at microwave frequencies which sees practical use in many emerging quantum device architectures. The goal of this research is to investigate improvements in TiN thin films utilizing MBE to produce highly pure, highly crystalline films. A review of the theory of superconducting qubits is given and recent developments in superconducting qubit research are summarized to elucidate how loss has been reduced historically and the importance of materials improvements to the future of scalable quantum computation. The dynamics of epitaxial film growth are discussed, focusing on the formation of a minimum energy surface, the thermally driven kinetics of atoms deposited on the surface, and how these lead to the formation of large scale crystalline domains in the film. An overview of the MBE growth chamber is given and the growth procedure for TiN is discussed. Transport and morphology measurement results are discussed for MBE TiN where, for optimized growth conditions, films are highly crystalline with superconducting transition temperatures(Tc) as high as Tc = 6.1K, matching the value for bulk crystals and exceeding all reported thin film values. Microwave loss measurements of transmission line resonators fabricated from these films are shown to have low-power quality factors(Q) as high as 200,000 and an increase to Q = 400,000 at high power, consistent with the saturation of two-level-systems (TLS) at high power. These results confirm a connection between the high quality crystalline materials produced in this work and low loss in quantum circuits.

•May 29, 2015•3 citations

Dispersive Spectrometry At Terahertz Frequencies for Probing the Quality of NbTiN Superconducting Films

Andrey V. Khudchenko, Bram Lap, Kirill I. Rudakov +9 more

We present the quality measurements of thick (thicker than London penetration depth) NbTiN superconducting films at Terahertz frequencies using a Dispersive Fourier Transform Spectrometer (DFTS). The reflected RF signal from the tested film was measured in time domain, allowing us to separate it from other reflections. The complex conductivity of the film depends on frequency and determines the reflection coefficient. By comparing the film reflection in superconducting state (film temperature below$Tc$) with that of the normal state (film temperature above$Tc$), we characterized the film quality at terahertz frequencies, and directly probed the energy of the superconducting gap of the tested film. The experimental results were fitted using the extended Mattis-Bardeen theory and th obtained film parameters show a good agreement with the literature. In addition to the DFTS, we have also measured the properties of NbTiN film using Time Domain Spectroscopy (TDS). It is shown that both TDS and DFTS provide similar results, and both techniques can be used for the quality control of thick NbTiN films. The superconducting gap determined from the measurements by both DFTS and TDS are in good agreement for both solid and meshed films showing that there is no remarkable degradation in the film quality due to technological processes of lift-off or ion etching.

IEEE Transactions on Applied Superconductivity•Feb 1, 2022•6 citations
For large-scale superconducting quantum technology, e.g. quantum computing, the homogeneity of wafer-scale superconducting thin films is vital for consistent performance of the fabricated devices. Terahertz (THz) spectroscopy as a contactless and non-destructive measurement technique is a powerful tool to characterize the superconducting films. In this work, a set of niobium titanium nitride (NbTiN) thin films on 4-inch and 6-inch silicon wafers, grown via plasma-enhanced magnetron sputtering, are investigated via THz spectroscopy: full wafers are mapped at room temperatures and exemplary segments are characterized at cryogenic temperatures. The deviations in observed sheet resistance depend on the used deposition device and the film thickness. While the deviations in superconducting sheet kinetic inductance match those of the normal-state sheet resistance, the critical temperature and energy gap exhibit little variation. This THz mapping technique demonstrates the feasibility of evaluating wafer-scale superconducting thin films before lithography, facilitating preparation of the thin films for reproducible device fabrication.
We have investigated superconducting properties of niobium titanium nitride (NbTiN) films to be used for the lower and upper electrodes of a microstrip line with a SiO2insulator on a quartz substrate at Terahertz frequencies. NbTiN films were prepared on a 1-mm thick quartz substrate directly (assumed to be the lower electrode of the microstrip line) and on an about 150-nm thick SiO2layer sputtered on a quartz substrate (assumed to be the upper electrode) by reactive dc magnetron sputtering at ambient temperature. The complex conductivity measurement by Terahertz time- domain spectroscopy revealed that both films have similar superconducting properties with critical temperatures of about 14 K and gap frequencies of about 1.2 THz at 5 K. This indicates that all-NbTiN microstrip lines may work well as extremely low-loss transmission lines at Terahertz frequencies.
The main focus of this work is the development of ultrathin NbN and NbTiN films. A reproducible and reliable deposition process for ultrathin NbN and NbTiN films for the use in phonon-cooled HEB devices was established. The ultrathin films were deposited on silicon (Si) substrates and on 2æm Si3N4 membranes by DC reactive magnetron sputtering. A method for the precise control of the nitrogen partial pressure by monitoring the target voltage has been introduced to deposit high quality, ultrathin NbN (3-4nm, Tc=8.5 K) and NbTiN (4-5nm, Tc=8K) films. Substrate heating of at least 600ʿC during the deposition is essential for the fabrication of ultrathin NbN and NbTiN films on Si substrates and Si3N4 membranes. The fabrication process required for HEB devices to be used in a quasi-optical mixer was developed. The ultrathin film was patterned by electron beam lithography (EBL), resulting in bolometer devices that measure areas of about 0.4 æm x 4 æm. The nature of the contact determines the interface transparency between the bolometer and the contact structure. Different cleaning processes have been performed and the influence on the contact resistance has been instigated. A better interface transparency gives less RF losses and could improve the HEB sensitivity and local oscillator (LO) requirement ...
In this paper, we present the development of the waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixers, cryogenically cooled by a 4 K close-cycled refrigerator. The NbTiN thin film is formed on a crystalline quartz substrate by sputtering an NbTi target with the Ar and N2gas at room temperature. The HEB mixer element is fabricated by using the 12 nm NbTiN film, and is mounted on a waveguide block. Measurement of a Fourier transform spectrometer shows that the response of the mixer is centered near 810 GHz with a bandwidth of about 500 GHz. The uncorrected DSB receiver noise temperature is measured to be 500 K, and the noise bandwidth is to be 1.4 GHz at 810 GHz. The present result shows that a good noise performance can be obtained for the NbTiN HEB mixer even with a relatively thick film (12 nm) fabricated at the room temperature.
Abstract Atomic layer deposition (ALD) has been identified as a promising growth method for high-uniformity superconducting thin films for superconducting quantum photonic applications, offering superior uniformity, thickness control and conformality to techniques such as reactive sputtering. The potential scalability of ALD makes this method especially appealing for fabrication of superconducting nanowires and resonators across large areas. We report on the growth of highly uniform superconducting NbN thin films via plasma-enhanced atomic layer deposition (PEALD) with radio frequency substrate biasing, on a 200 mm (8 inch) Si wafer, specifically for superconducting nanowire single-photon detector applications. Niobium nitride films were grown using (tert-butylimido)-tris(diethylamido)-niobium(V) precursor and an H 2 /Ar plasma. The superconducting properties of a variable thickness series of films (5.9–29.8 nm) show critical temperature ( T c ) of 13.5 K approaching bulk thickness (28.8 nm) with low suppression down to the ultrathin regime (5.9 nm), with T c = 10.2 K. T c across the 200 mm wafer with 8 nm thick NbN, measured in 15 mm intervals, exhibits minimal variation (<7%). Microbridge structures fabricated on 8 nm thick NbN films also exhibit high critical current densities ( J c ), > 10 MA cm −2 at 2.6 K. PEALD could therefore be a pivotal technique in enabling large-scale fabrication of integrated quantum photonic devices across a variety of applications.
This is a study of the growth of titanium-nitride (TiN) by plasma assisted molecular beam epitaxy (MBE) for applications in low loss quantum circuits. Titanium nitride is a material known to have low loss at microwave frequencies which sees practical use in many emerging quantum device architectures. The goal of this research is to investigate improvements in TiN thin films utilizing MBE to produce highly pure, highly crystalline films. A review of the theory of superconducting qubits is given and recent developments in superconducting qubit research are summarized to elucidate how loss has been reduced historically and the importance of materials improvements to the future of scalable quantum computation. The dynamics of epitaxial film growth are discussed, focusing on the formation of a minimum energy surface, the thermally driven kinetics of atoms deposited on the surface, and how these lead to the formation of large scale crystalline domains in the film. An overview of the MBE growth chamber is given and the growth procedure for TiN is discussed. Transport and morphology measurement results are discussed for MBE TiN where, for optimized growth conditions, films are highly crystalline with superconducting transition temperatures(Tc) as high as Tc = 6.1K, matching the value for bulk crystals and exceeding all reported thin film values. Microwave loss measurements of transmission line resonators fabricated from these films are shown to have low-power quality factors(Q) as high as 200,000 and an increase to Q = 400,000 at high power, consistent with the saturation of two-level-systems (TLS) at high power. These results confirm a connection between the high quality crystalline materials produced in this work and low loss in quantum circuits.
We present the quality measurements of thick (thicker than London penetration depth) NbTiN superconducting films at Terahertz frequencies using a Dispersive Fourier Transform Spectrometer (DFTS). The reflected RF signal from the tested film was measured in time domain, allowing us to separate it from other reflections. The complex conductivity of the film depends on frequency and determines the reflection coefficient. By comparing the film reflection in superconducting state (film temperature belowTcTcTc) with that of the normal state (film temperature aboveTcTcTc), we characterized the film quality at terahertz frequencies, and directly probed the energy of the superconducting gap of the tested film. The experimental results were fitted using the extended Mattis-Bardeen theory and th obtained film parameters show a good agreement with the literature. In addition to the DFTS, we have also measured the properties of NbTiN film using Time Domain Spectroscopy (TDS). It is shown that both TDS and DFTS provide similar results, and both techniques can be used for the quality control of thick NbTiN films. The superconducting gap determined from the measurements by both DFTS and TDS are in good agreement for both solid and meshed films showing that there is no remarkable degradation in the film quality due to technological processes of lift-off or ion etching.