Trapped ions have proven to be effective quantum bits; but increasing electric field noise as traps are miniaturized limits gate fidelity and progress towards a large-scale quantum computer. Removing contamination from surfaces is important for noise suppression; but cleaning techniques like argon ion bombardment are difficult to integrate with current systems and are too harsh for traps incorporating optical devices. We investigate an alternative solution: a protective coating against surface contamination. We fabricate copper traps with a graphene passivation layer and characterize them with single ions. Surprisingly, we find worse noise performance than for an uncoated metal trap.
Trapped ions have proven to be effective quantum bits; but increasing electric field noise as traps are miniaturized limits gate fidelity and progress towards a large-scale quantum computer. Removing contamination from surfaces is important for noise suppression; but cleaning techniques like argon ion bombardment are difficult to integrate with current systems and are too harsh for traps incorporating optical devices. We investigate an alternative solution: a protective coating against surface contamination. We fabricate copper traps with a graphene passivation layer and characterize them with single ions. Surprisingly, we find worse noise performance than for an uncoated metal trap.
All surfaces generate electric-field noise, yet the physical origins of this noise are not well understood. This has been an active area of research in the ion trapping community for the past two decades, as ions are highly sensitive to electric-field fluctuations. With our work, we aim to illuminate the microscopic processes that drive charge dynamics on metal surfaces, so as to enable the engineering of low noise quantum devices. We use single trapped calcium ions as detectors to study the 1/f noise generated by the surfaces of ion traps. We the study this noise by observing how it responds to changes in the properties of the trap surface. The surface properties are altered using treatments including prolonged heating, argon ion milling, and electron bombardment. In situ characterization tools are used to monitor the effects of these treatments. Our measurements are consistent with noise produced by an ensemble of thermally activated fluctuators, so our data is discussed in this context. In this dissertation, we present results from a lengthy series of surface treatment experiments, the majority of which took place on a single aluminum-copper substrate. The results of these experiments indicate that argon ion milling can lower noise both by removing contaminants and by altering the morphology of the trap surface. The effects of morphology are isolated from the effects of contaminant removal via heat treatments, which alter the structure of the surface without changing its chemical composition. Through electron bombardment experiments, we begin an exploration of the relationship between hydrocarbon adsorbate structure and electric-field noise. In addition, we compare the noise characteristics of a set of similarly fabricated traps, and determine that atmosphere exposure has a major impact on noise produced by aluminum-copper films.These experiments establish links between the electric-field noise characteristics and the microscopic properties of a contaminated metal trap surface. The insights we draw in this work can inform the next generation of ion trap engineering, storage, and treatment.
Motional heating of trapped atomic ions is a major obstacle to their use as quantum bits in a scalable quantum computer. The detailed physical origin of this heating is not well understood, but experimental evidence suggests that it is caused by electric-field noise emanating from the surface of the trap electrodes. In this study, we have investigated the role of adsorbates on the electrodes by identifying contaminant overlayers, implementing an in situ argon-ion-beam cleaning treatment, and measuring ion heating rates before and after treating the trap electrodes' surfaces. We find a 100-fold reduction in heating rate after treatment. The experiments described here are sensitive to low levels of electric-field noise in the MHz frequency range. Therefore, this approach could become a useful tool in surface science that complements established techniques.
We use a single-ion electric-field noise sensor in combination with in situ surface treatment and analysis tools, to investigate the relationship between electric-field noise from metal surfaces in vacuum and the composition of the surface. These experiments are performed in a setup that integrates ion trapping capabilities with surface analysis tools. We find that treatment of an aluminum-copper surface with energetic argon ions significantly reduces the level of room-temperature electric-field noise, but the surface does not need to be atomically clean to show noise levels comparable to those of the best cryogenic traps. The noise levels after treatment are low enough to allow fault-tolerant trapped-ion quantum information processing on a microfabricated surface trap at room temperature.
Electric field noise is a hinderance to the assembly of large-scale quantum computers based on entangled trapped ions. Apart from ubiquitous technical noise, experimental studies of trapped ion heating have revealed additional limiting contributions to this noise, originating from atomic processes on the electrode surfaces. In a recent work [Safavi-Naini, Rabl, Weck, and Sadeghpour, Phys. Rev. A 84, 023412 (2011)] we described a microscopic model for this excess electric field noise, which points a way towards a more systematic understanding of surface adsorbates as progenitors of electric field jitter noise. Here, we address the impact of surface monolayer contamination on adsorbate-induced noise processes. Using exact numerical calculations for H and N atomic monolayers on a Au(111) surface, representing opposite extremes of physisorption and chemisorption, we show that an additional monolayer can significantly affect the noise power spectrum and, respectively, enhance and suppress the heating rates.
The major challenges in trapped-ion quantum computation are to scale up few-ion experiments to many qubits and to improve control techniques so that quantum logic gates can be carried out with higher fidelities. This thesis reports experimental progress in both of these areas. In the early part of the thesis we describe the fabrication of a surface-electrode ion trap, the development of the apparatus and techniques required to operate it and the successful trapping of 40Ca+ ions. Notably we developed methods to control the orientation of the principal axes and to minimise ion micromotion. We propose a repumping scheme that simplifies heating rate measurements for ions with low-lying D levels, and use it to characterise the electric field noise in the trap. Surface-electrode traps are important because they offer a route to dense integration of electronic and optical control elements using existing microfabrication technology. We explore this scaling route by testing a series of three traps that were microfabricated at Sandia National Laboratories. Investigations of micromotion and charging of the surface by laser beams were carried out and improvements to future traps are suggested. Using one of these traps we also investigated anomalous electrical noise from the electrode surfaces and discovered that it can be reduced by cleaning with a pulsed laser. A factor of two decrease was observed; this represents the first in situ removal of this noise source, an important step towards higher gate fidelities. In the second half of the thesis we describe the design and construction of an experiment for the purpose of replacing laser-driven multi-qubit quantum logic gates with microwave-driven ones. We investigate magnetic-field-independent hyperfine qubits in 40Ca+ as suitable qubits for this scheme. We make a design study of how best to integrate an ion trap with the microwave conductors required to implement the gate and propose a novel integrated resonant structure. The trap was fabricated and ions were successfully loaded. Single-qubit experiments show that the microwave fields above the trap are in excellent agreement with software simulations. There are good prospects for demonstrating a multi-qubit gate in the near future. We conclude by discussing the possibilities for larger-scale quantum computation by combining microfabricated traps and microwave control.
Electric field noise produced by the surface of ion trap electrodes reduces the fidelity of quantum computing operations. Despite decades of investigation its microscopic origins remain unclear. Here, we measure electric field noise at trapping locations along the symmetry axis of a linear surface Paul trap. We find that noise levels vary by three orders-of-magnitude in one 600μm section of the trap. Optical and scanning electron microscope images show micron-sized particles close to the trapping locations with the highest noise levels. We find that modeling the particles as a lossy dielectric with a effective loss tangent tanθ=0.33(0.06) describes the magnitude of the noise, as well as its spatial and frequency dependence. Our observations may explain the large variation of reported noise levels in literature.