Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Hard Magnetic Dots for Flux Bias of DC SQUIDs

Dušan S. Golubović, V. V. Moshchalkov

Published Sep 1, 2006• 0 citations
Publisher

Abstract

In this paper, we demonstrate that perpendicularly magnetized sub- and micrometer-sized magnetic dots, with a high coercivity and nearly complete remanence, can be used to provide the flux bias for dc superconducting quantum interference devices (SQUIDs). The radius of a submicrometer Co-Pd magnetic dot has been optimized with respect to the surrounding superconducting circuitry to generate the phase shift of approximately pi/2 in it. In this way, it is possible to bias a dc SQUID to the steepest part of its voltage-flux characteristic without using an additional coil and current source. Furthermore, it has been shown that the flux bias can also be achieved using a micrometer-sized Co-Pd dot, upon saturation, by placing a dc SQUID on top of the dot. Given that the underlying principles of flux biasing do not require any particular superconducting pairing scheme (s- or d-wave), these hybrid superconductor/ferromagnet structures can be used as to design a dc SQUID with a complete flux self-biasing

DOI
10.1109/tasc.2006.873994

Related papers

Tuning an rf-SQUID flux qubit system's potential with magnetic flux bias

Tao Hua, Weiwei Xu, Jianxin Shi +4 more

At an extremely low temperature of 20 mK, we measured the loop current in a tunable rf superconducting quantum interference device (SQUID) with a dc-SQUID. By adjusting the magnetic flux applied to the rf-SQUID loop ( Φ f ) and the small dc-SQUID ( Φ f cjj ), respectively, the potential shape of the system can be fully controlled in situ . Variation in the transition step and overlap size in the switching current with a barrier flux bias are analyzed, from which we can obtain some relevant device parameters and build a model to explain the experimental phenomenon.

Chinese Physics B•Sep 1, 2012•4 citations

Radio frequency bias current scheme for dc superconducting quantum interference device

Y. Zhang, Dongfeng He, N. Wolters +7 more

We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•0 citations

dc SQUID's I–V Characteristics and Its Bias Modes

Yi Zhang, Hui Dong, Hans-Joachim Krause +2 more

The physics of a DC Superconducting QUantum Interference Device (SQUID) involves two phenomena: flux quantization and Josephson tunneling. This chapter describes how to measure and understand a SQUID's I–V characteristics. It also describes how to realize an ideal current source for biasing a SQUID and how to set up a practical voltage source to operate a SQUID in voltage bias mode. To study a DC SQUID's features, the first step is to obtain its I–V characteristics. In contrast to the I–V characteristics of the resistor or the diode, those of the SQUID are modulated by the applied flux but are limited within two flux states of integer and half-integer. An ideal current source is characterized by an internal resistance approaching infinity, compared to the SQUID's dynamic resistance. There are only two realized concepts for the SQUID operation in voltage bias mode.

Wiley eBooks•May 29, 2020•0 citations

Micro-superconducting quantum interference devices based on V/Cu/V Josephson nanojunctions

Alberto Ronzani, Matthieu Baillergeau, Carles Altimiras +1 more

We report on the fabrication and characterization of micrometer-sized superconducting quantum interference devices (SQUIDs) based on nanoscale vanadium/copper/vanadium Josephson weak links. Magnetically driven quantum interference patterns have been measured for temperatures in the 0.24–2 K range. As DC SQUIDs, these devices obtain flux-to-voltage transfer function values as high as 450 μV/Φ0 leading to promising magnetic flux resolution ΦN<3 μΦ0/Hz, being here limited by the room temperature preamplification stage. Significant improvement in the flux noise performance figures is expected with the adoption of cryogenic preamplification. The presented devices are suitable for operation as small-area SQUIDs at sub-Kelvin temperature, but their design can also be upscaled to include input coils enabling their use as sensitive magnetometers via the adoption of optimized electronic readout stages based on flux feedback schemes.

arXiv:1305.3863•Applied Physics Letters•Jul 29, 2013•27 citations

An absolute magnetometer based on dc Superconducting QUantum Interference Devices

P. Carelli, Maria Gabriella Castellano, K Flacco +2 more

We propose a novel device, based on a series of dc SQUIDs (direct current Superconducting QUantum Interference Devices), each one with different sensitive area, that can be used to perform absolute measurements of magnetic field. With this array, we overcome the limit of a single dc SQUID of being sensitive only to variations of the linked magnetic flux. The overall voltage-flux characteristic of our device, in fact, has a non-periodic shape that allows a clear identification of the point with zero magnetic field. We present a discussion of the working principle and of the main characteristics, which have been partially tested on a prototype.

Europhysics Letters (EPL)•Sep 1, 1997•28 citations

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•1 citation
In this paper, we demonstrate that perpendicularly magnetized sub- and micrometer-sized magnetic dots, with a high coercivity and nearly complete remanence, can be used to provide the flux bias for dc superconducting quantum interference devices (SQUIDs). The radius of a submicrometer Co-Pd magnetic dot has been optimized with respect to the surrounding superconducting circuitry to generate the phase shift of approximately pi/2 in it. In this way, it is possible to bias a dc SQUID to the steepest part of its voltage-flux characteristic without using an additional coil and current source. Furthermore, it has been shown that the flux bias can also be achieved using a micrometer-sized Co-Pd dot, upon saturation, by placing a dc SQUID on top of the dot. Given that the underlying principles of flux biasing do not require any particular superconducting pairing scheme (s- or d-wave), these hybrid superconductor/ferromagnet structures can be used as to design a dc SQUID with a complete flux self-biasing
At an extremely low temperature of 20 mK, we measured the loop current in a tunable rf superconducting quantum interference device (SQUID) with a dc-SQUID. By adjusting the magnetic flux applied to the rf-SQUID loop ( Φ f ) and the small dc-SQUID ( Φ f cjj ), respectively, the potential shape of the system can be fully controlled in situ . Variation in the transition step and overlap size in the switching current with a barrier flux bias are analyzed, from which we can obtain some relevant device parameters and build a model to explain the experimental phenomenon.
We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.
The physics of a DC Superconducting QUantum Interference Device (SQUID) involves two phenomena: flux quantization and Josephson tunneling. This chapter describes how to measure and understand a SQUID's I–V characteristics. It also describes how to realize an ideal current source for biasing a SQUID and how to set up a practical voltage source to operate a SQUID in voltage bias mode. To study a DC SQUID's features, the first step is to obtain its I–V characteristics. In contrast to the I–V characteristics of the resistor or the diode, those of the SQUID are modulated by the applied flux but are limited within two flux states of integer and half-integer. An ideal current source is characterized by an internal resistance approaching infinity, compared to the SQUID's dynamic resistance. There are only two realized concepts for the SQUID operation in voltage bias mode.
We report on the fabrication and characterization of micrometer-sized superconducting quantum interference devices (SQUIDs) based on nanoscale vanadium/copper/vanadium Josephson weak links. Magnetically driven quantum interference patterns have been measured for temperatures in the 0.24–2 K range. As DC SQUIDs, these devices obtain flux-to-voltage transfer function values as high as 450 μV/Φ0 leading to promising magnetic flux resolution ΦN<3 μΦ0/Hz, being here limited by the room temperature preamplification stage. Significant improvement in the flux noise performance figures is expected with the adoption of cryogenic preamplification. The presented devices are suitable for operation as small-area SQUIDs at sub-Kelvin temperature, but their design can also be upscaled to include input coils enabling their use as sensitive magnetometers via the adoption of optimized electronic readout stages based on flux feedback schemes.
We propose a novel device, based on a series of dc SQUIDs (direct current Superconducting QUantum Interference Devices), each one with different sensitive area, that can be used to perform absolute measurements of magnetic field. With this array, we overcome the limit of a single dc SQUID of being sensitive only to variations of the linked magnetic flux. The overall voltage-flux characteristic of our device, in fact, has a non-periodic shape that allows a clear identification of the point with zero magnetic field. We present a discussion of the working principle and of the main characteristics, which have been partially tested on a prototype.
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.