Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)

Atomic vapor cells for miniature frequency references

Svenja A. Knappe, Vladimir L Velichansky, H. G. Robinson, Li‐Anne Liew, John Moreland, John E. Kitching, Leo W. Hollberg

Published Jul 8, 2004• 33 citations
Publisher

Abstract

We report on the fabrication of millimeter-sized vapor cells and their performance in atomic clocks based on coherent population trapping (CPT). We discuss two fabrication techniques. The first one is based on hollow-core pyrex fibers, fused with a CO/sub 2/ laser or micro-torch, and the second one involves anodic bonding of micro-machined silicon wafers to pyrex. Key aspects of the discussion are the performance of the cell in frequency references, the potential for further miniaturization of the cells and the ability to manufacture them on a large scale with reproducible performance.

DOI
10.1109/freq.2003.1274981

Related papers

Fabrication of Cesium Vapor Cells for Chip-Scale Atomic Clock Based on Coherent Population Trapping

Alexey Kazakin, Yu. D. Akul'shin, Yakov Enns +3 more

The article presents the results of the development, fabrication and investigation of miniature cesium vapor cells for quantum frequency standards with optical pumping, working on the effect of coherent population trapping. Microelectromechanical systems technologies were used in the manufacture of cells. For the first time, the dry silicon etching in inductively coupled plasma of sulfur hexafluoride and freon gas in a mixed mode was used to form internal cavities of cells with a thickness of 1.5 mm. Vacuum-tight sealing of cells containing a solid-state source of cesium vapor and buffer gas was carried out by anodic bonding of glass and silicon in a neon atmosphere. The coherent population trapping signal with a linewidth of 750 Hz and a signal-to-noise ratio of 1190 in the 1-Hz bandwidth was observed. Experimental results show that these microcells are appropriate for applications to atomic clock with a relative frequency stability of$6\cdot 10^{-11}$at 1 s.

International Conference on Electrical Engineering and Photonics (EExPolytech)•Oct 20, 2022•1 citation

Microfabricated Alkali Atom Vapor Cells for Chip Scale Atomic Clock

M.-Z. Huang, Jiashan Zhu, Guangfeng Shi +2 more

In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.

Annual Conference of the Chinese Society of Micro-Nano Technology (CSMNT)•Nov 22, 2017•0 citations

Micromachined alkali atom vapor cells for chip-scale atomic clocks

Li‐Anne Liew, Svenja A. Knappe, John Moreland +3 more

This paper describes the fabrication of chip-scale alkali atom vapor cells, for use in highly miniaturized atomic frequency references, using silicon micromachining and anodic bonding technology. The cells consist of silicon cavities with internal volume ranging from a few mm/sup 3/ to less than 1 mm/sup 3/. The cells were filled with cesium and nitrogen buffer gas either by chemical reaction of cesium chloride and barium azide, or by direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption spectra were obtained from the cells, and coherent population trapping resonances with linewidths of about 1 kHz were measured.

IEEE International Conference on Micro Electro Mechanical Systems (MEMS)•Aug 2, 2004•15 citations

Micro Rb atomic vapor cells for the chip-scale atomic clock

Chang Zhang, Shuangyou Zhang, Guo Dengzhu +2 more

Nowadays, the portable atomic clocks with small size and low power consumption have attracted much attention. With the development of the coherent population trapping (CPT) and the micro-electro-mechanical systems (MEMS) technologies, it is possible to fabricate the miniature atomic clocks with power consumption less than 100mW. Researchers have already made great progress in the miniaturization of VCSELs, RF circuits, and photodiodes, which are the key technologies of the chip-scale atomic clock (CSAC). However, the fabrication of micro alkali atomic vapor cells is still to be improved. In this article, we describe the fabrication of micro Rb atomic vapor cells with inner dimensions of 3 mm length and 3 mm radius using anodic bonding and chemical reaction between BaN6and RbCl. The optical absorption and CPT resonances of the cells were measured slightly above the room temperature. In this condition, the consumption in the temperature control will be very low. Moreover, the long life (more than four years) of the cells makes it possible to use them in CSACs.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•May 1, 2014•4 citations

The Microfabricated Alkali Vapor Cell with High Hermeticity for Chip-Scale Atomic Clock

Shuo Jia, Zhiyuan Jiang, Binbin Jiao +4 more

Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.

Applied Sciences•Jan 3, 2022•21 citations

Microfabricated alkali atom vapor cells

Li‐Anne Liew, Svenja A. Knappe, John Moreland +3 more

We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.

Applied Physics Letters•Apr 1, 2004•377 citations
We report on the fabrication of millimeter-sized vapor cells and their performance in atomic clocks based on coherent population trapping (CPT). We discuss two fabrication techniques. The first one is based on hollow-core pyrex fibers, fused with a CO/sub 2/ laser or micro-torch, and the second one involves anodic bonding of micro-machined silicon wafers to pyrex. Key aspects of the discussion are the performance of the cell in frequency references, the potential for further miniaturization of the cells and the ability to manufacture them on a large scale with reproducible performance.
The article presents the results of the development, fabrication and investigation of miniature cesium vapor cells for quantum frequency standards with optical pumping, working on the effect of coherent population trapping. Microelectromechanical systems technologies were used in the manufacture of cells. For the first time, the dry silicon etching in inductively coupled plasma of sulfur hexafluoride and freon gas in a mixed mode was used to form internal cavities of cells with a thickness of 1.5 mm. Vacuum-tight sealing of cells containing a solid-state source of cesium vapor and buffer gas was carried out by anodic bonding of glass and silicon in a neon atmosphere. The coherent population trapping signal with a linewidth of 750 Hz and a signal-to-noise ratio of 1190 in the 1-Hz bandwidth was observed. Experimental results show that these microcells are appropriate for applications to atomic clock with a relative frequency stability of6⋅10−116\cdot 10^{-11}6⋅10−11at 1 s.
In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.
This paper describes the fabrication of chip-scale alkali atom vapor cells, for use in highly miniaturized atomic frequency references, using silicon micromachining and anodic bonding technology. The cells consist of silicon cavities with internal volume ranging from a few mm/sup 3/ to less than 1 mm/sup 3/. The cells were filled with cesium and nitrogen buffer gas either by chemical reaction of cesium chloride and barium azide, or by direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption spectra were obtained from the cells, and coherent population trapping resonances with linewidths of about 1 kHz were measured.
Nowadays, the portable atomic clocks with small size and low power consumption have attracted much attention. With the development of the coherent population trapping (CPT) and the micro-electro-mechanical systems (MEMS) technologies, it is possible to fabricate the miniature atomic clocks with power consumption less than 100mW. Researchers have already made great progress in the miniaturization of VCSELs, RF circuits, and photodiodes, which are the key technologies of the chip-scale atomic clock (CSAC). However, the fabrication of micro alkali atomic vapor cells is still to be improved. In this article, we describe the fabrication of micro Rb atomic vapor cells with inner dimensions of 3 mm length and 3 mm radius using anodic bonding and chemical reaction between BaN6and RbCl. The optical absorption and CPT resonances of the cells were measured slightly above the room temperature. In this condition, the consumption in the temperature control will be very low. Moreover, the long life (more than four years) of the cells makes it possible to use them in CSACs.
Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.
We describe the fabrication of chip-sized alkali atom vapor cells using silicon micromachining and anodic bonding technology. Such cells may find use in highly miniaturized atomic frequency references or magnetometers. The cells consist of cavities etched in silicon, with internal volumes as small as 1 mm3. Two techniques for introducing cesium and a buffer gas into the cells are described: one based on chemical reaction between cesium chloride and barium azide, and the other based on direct injection of elemental cesium within a controlled anaerobic environment. Cesium optical absorption and coherent population trapping resonances were measured in the cells.