Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

A readout system for 3-GHz rf-SQUIDs

Michael Mück

Published Apr 1, 1992• 14 citations
Publisher

Abstract

The layout and construction of a readout electronics for rf superconducting quantum interference devices (SQUIDs) with bias frequencies of 3 GHz are described. The electronics uses standard electronic components and can be aligned using a spectrum analyzer. Differences between a conventional 20-MHz electronics and this microwave readout are explained. Each individual circuit block is described and circuit diagrams as well as information for pc-board layout is given. A brief description of thin-film rf-SQUIDs used for experiments with this readout electronics is also included.

DOI
10.1063/1.1143149

Related papers

Design and implementation of A 06 GHz - 09 GHz RF-SQUID Read-out system and investigation of rf-SQUID signal characteristics

Taylan Eker

Design and implementation of a transceiver system for rf-SQUID (Superconducting Quantum Interference Device) operation is investigated in this work. Besides, experiments to characterize the rf-SQUID have been performed using the implemented system. The steps in system design and implementation are presented. The difficulties and drawbacks of the system are reported and alternative techniques required to overcome these problems are determined. Also, for the operation of the rf-SQUID at much higher frequencies, different transceiver architecture is proposed and possible drawbacks are stated. Using implemented system, several experiments were performed on two high Tc rfSQUID gradiometers with a tank-circuit resonating at 720 MHz. In these experiments, the frequency and amplitude of the applied rf signal were swept and output flux to voltage transfer signal (modulation added by rf-SQUID), Vspp, and incoming rf signal spectrum are reported and analyzed.

•Jan 1, 2005•0 citations

Use of super Schottky diodes in a cryogenic radio frequency superconducting quantum interference device readout

Michael Mück, Th. Becker, Christoph Heiden

We describe the fabrication and characterization of super Schottky diodes which are used in the cryogenic part of a 3 GHz radio frequency superconducting quantum interference device (rf SQUID) readout electronics. The diodes were prepared on silicon wafers with an n-doping level of 5×1024 m−3. They exhibited sensitivities of 1500 V−1 at 4.2 K, and a noise equivalent power of 2×10−15 W/√Hz was measured at 2.1 GHz. Using planar niobium 3 GHz rf SQUIDs and a cooled rf amplifier, experiments have been performed to investigate the feasibility of these super Schottky diodes for demodulation of the SQUID rf signal voltage. A simple cryogenic rf SQUID readout, employing two transistors and one super Schottky diode is described and investigated. Flux noise measurements in an open loop have been performed using this readout.

Applied Physics Letters•Jan 16, 1995•2 citations

Radio‐Frequency (rf) SQUID

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

To read out radio frequency (rf) superconducting quantum interference device (SQUID) signals, an rf resonance tank circuit is usually needed. Similar to dc SQUID systems, an rf SQUID system also detects a flux signal that can change slowly over time. In fact, rf SQUID readout electronics exhibit potential advantages over dc SQUID electronics in the direct readout scheme. A merit of rf SQUID systems is the need for just one coaxial cable to connect the readout electronics to the two-terminal element. In a complete magnetometric SQUID system, an input coil connects to a receiver loop (flux antenna) to pick up the measured signals and couples it to the SQUID via a mutual inductance. This chapter discusses the main differences between rf SQUIDs and dc SQUIDs. The significant difference between rf and DC SQUIDs is the occurrence of higher harmonic components in the flux-to-voltage characteristics.

Wiley eBooks•May 29, 2020•0 citations

Radio frequency pumped superconducting quantum interference devices with two quantization loops

G.S. Krivoy, H. Koch

Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.

Journal of Applied Physics•Aug 15, 1993•16 citations

Radio frequency bias current scheme for dc superconducting quantum interference device

Y. Zhang, Dongfeng He, N. Wolters +7 more

We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•0 citations

Investigation and reduction of excess low-frequency noise in rf superconducting quantum interference devices

Michael Mück, Christoph Heiden, John L. Clarke

A detailed study has been made of the low-frequency excess noise of rf superconducting quantum interference devices (SQUIDs), fabricated from thin niobium films and operated at 4.2 K, with rf bias frequencies of 0.15, 1.7, and 3 GHz. When the SQUIDs were operated in an open-loop configuration in the absence of low-frequency flux modulation, the demodulated rf voltage exhibited a substantial level 1/f noise, which was essentially independent of the rf bias frequency. As the rf bias frequency was increased, the crossover frequency at which the 1/f noise power was equal to the white noise power moved to higher frequencies, because of the reduction in white noise. On the other hand, when the SQUID was flux modulated at 50 kHz and operated in a flux locked loop, no 1/f noise was observed at frequencies above 0.5 Hz. A detailed description of how the combination of rf bias and flux modulation removes 1/f noise due to critical current fluctuations is given. Thus, the results demonstrate that the 1/f noise observed in these SQUIDs is generated by critical current fluctuations, rather than by the hopping of flux vortices in the niobium films.

Journal of Applied Physics•May 1, 1994•26 citations
The layout and construction of a readout electronics for rf superconducting quantum interference devices (SQUIDs) with bias frequencies of 3 GHz are described. The electronics uses standard electronic components and can be aligned using a spectrum analyzer. Differences between a conventional 20-MHz electronics and this microwave readout are explained. Each individual circuit block is described and circuit diagrams as well as information for pc-board layout is given. A brief description of thin-film rf-SQUIDs used for experiments with this readout electronics is also included.
Design and implementation of a transceiver system for rf-SQUID (Superconducting Quantum Interference Device) operation is investigated in this work. Besides, experiments to characterize the rf-SQUID have been performed using the implemented system. The steps in system design and implementation are presented. The difficulties and drawbacks of the system are reported and alternative techniques required to overcome these problems are determined. Also, for the operation of the rf-SQUID at much higher frequencies, different transceiver architecture is proposed and possible drawbacks are stated. Using implemented system, several experiments were performed on two high Tc rfSQUID gradiometers with a tank-circuit resonating at 720 MHz. In these experiments, the frequency and amplitude of the applied rf signal were swept and output flux to voltage transfer signal (modulation added by rf-SQUID), Vspp, and incoming rf signal spectrum are reported and analyzed.
We describe the fabrication and characterization of super Schottky diodes which are used in the cryogenic part of a 3 GHz radio frequency superconducting quantum interference device (rf SQUID) readout electronics. The diodes were prepared on silicon wafers with an n-doping level of 5×1024 m−3. They exhibited sensitivities of 1500 V−1 at 4.2 K, and a noise equivalent power of 2×10−15 W/√Hz was measured at 2.1 GHz. Using planar niobium 3 GHz rf SQUIDs and a cooled rf amplifier, experiments have been performed to investigate the feasibility of these super Schottky diodes for demodulation of the SQUID rf signal voltage. A simple cryogenic rf SQUID readout, employing two transistors and one super Schottky diode is described and investigated. Flux noise measurements in an open loop have been performed using this readout.
To read out radio frequency (rf) superconducting quantum interference device (SQUID) signals, an rf resonance tank circuit is usually needed. Similar to dc SQUID systems, an rf SQUID system also detects a flux signal that can change slowly over time. In fact, rf SQUID readout electronics exhibit potential advantages over dc SQUID electronics in the direct readout scheme. A merit of rf SQUID systems is the need for just one coaxial cable to connect the readout electronics to the two-terminal element. In a complete magnetometric SQUID system, an input coil connects to a receiver loop (flux antenna) to pick up the measured signals and couples it to the SQUID via a mutual inductance. This chapter discusses the main differences between rf SQUIDs and dc SQUIDs. The significant difference between rf and DC SQUIDs is the occurrence of higher harmonic components in the flux-to-voltage characteristics.
Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.
We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.
A detailed study has been made of the low-frequency excess noise of rf superconducting quantum interference devices (SQUIDs), fabricated from thin niobium films and operated at 4.2 K, with rf bias frequencies of 0.15, 1.7, and 3 GHz. When the SQUIDs were operated in an open-loop configuration in the absence of low-frequency flux modulation, the demodulated rf voltage exhibited a substantial level 1/f noise, which was essentially independent of the rf bias frequency. As the rf bias frequency was increased, the crossover frequency at which the 1/f noise power was equal to the white noise power moved to higher frequencies, because of the reduction in white noise. On the other hand, when the SQUID was flux modulated at 50 kHz and operated in a flux locked loop, no 1/f noise was observed at frequencies above 0.5 Hz. A detailed description of how the combination of rf bias and flux modulation removes 1/f noise due to critical current fluctuations is given. Thus, the results demonstrate that the 1/f noise observed in these SQUIDs is generated by critical current fluctuations, rather than by the hopping of flux vortices in the niobium films.