Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Softwaretechnik-Trends

A 665 GHz Waveguide Receiver Using a Tuned 0.5 μm 2 Nb/AlO x /Nb SIS Tunnel Junction

J. Kooi, Mansun Chan, Henry George LeDuc, Tom G. Phillips

Published Mar 1, 1996• 1 citation
OpenAlex

Abstract

We report recent results on a 580-740 GHz SIS heterodyne receiver employing a tuned 0.50Am Nb/A10x/Nb SIS tunnel junction. The receiver has been successfully installed at the Caltech Submillimeter Observatory, Hawaii. Results of an untuned device in the same waveguide block were presented at the fifth International THz Conference. Since the mixer is meant to be operated near the superconducting gap frequency of niobium (2,L/h 690 GHz), special has been taken to minimize the absorption loss in the rf matching network. To this effect we propose the use of a RF matching network that constitutes a hybrid between the well know end-loaded stub and radial stub matching networks. We have measured uncorrected DSB receiver temperatures as low as 160K from 680to 702 Gliz, 200K at 725GHz and 120K from 585-640 GHz. The uncorrected mixer noise temperature at 702 Gliz is about 125K, of which 62K can be directly contributed to the front end optics loss. Mixer conversion loss at 702 GHz is 7dB, of which 0.9dB is due to the absorption loss in the Nb film. This results in a corrected mixer noise temperature of 63K, 1.7 times the quantum noise limit.

Related papers

A 850-GHz waveguide receiver employing a niobium SIS junction fabricated on a 1-μm Si/sub 3/N/sub 4/ membrane

J. Kooi, Jérôme Pety, B. Bumble +4 more

We report on a 850-GHz superconducting-insulator-superconducting (SIS) heterodyne receiver employing an RF-tuned niobium tunnel junction with a current density of 14 kA/cm^2, fabricated on a 1-µm Si_3N_4 supporting membrane. Since the mixer is designed to be operated well above the superconducting gap frequency of niobium (2Δ/h ≈ 690 GHz), special care has been taken to minimize niobium transmission-line losses. Both Fourier transform spectrometer (FTS) measurements of the direct detection performance and calculations of the IF output noise with the mixer operating in heterodyne mode, indicate an absorption loss in the niobium film of about 6.8 dB at 822 GHz. These results are in reasonably good agreement with the loss predicted by the Mattis-Bardeen theory in the extreme anomalous limit. From 800 to 830 GHz, we report uncorrected receiver noise temperatures of 518 or 514 K when we use Callen and Welton's law to calculate the input load temperatures. Over the same frequency range, the mixer has a 4-dB conversion loss and 265 K ± 10 K noise temperature. At 890 GHz, the sensitivity of the receiver has degraded to 900 K, which is primarily the result of increased niobium film loss in the RF matching network. When the mixer was cooled from 4.2 to 1.9 K, the receiver noise temperature improved about 20% 409-K double sideband (DSB). Approximately half of the receiver noise temperature improvement can be attributed to a lower mixer conversion loss, while the remainder is due to a reduction in the niobium film absorption loss. At 982 GHz, we measured a receiver noise temperature of 1916 K.

IEEE Transactions on Microwave Theory and Techniques•Jan 1, 1998•21 citations

Quasi-optical submillimeter-wave SIS mixers with NbN/A1N/NbN tunnel junctions

Yoshinori Uzawa, Zhen Wang, Akira Kawakami

We report on low-noise heterodyne mixing with NbN/A1N/NbN tunnel junctions in the submillimeter-wave region for the first time. The receiver consists of the quasi-optical NbN SIS mixer with an integrated tuning circuit in which a radial short stub tuner is incorporated to resonate out the junction capacitance for RF matching and a balanced IF circuit for broadband IF matching. The prepared NbN SIS junction has a current density of 20 kA/cm 2 and is about 1 I1111 in diameter, supplying a small coC JRN product (o)CJRN = 3 at 300 GHz). The junctions showed good dc I-V characteristics, excellent submillimeter-wave responses and sensitive heterodyne mixing responses. From 254 to 350 GHz the average receiver noise temperature measured using by the standard Y-factor method was about 250 K (DSB) at 5 K. The lowest receiver noise temperature, 200 K (DSB), was obtained at around 303 GHz. Comparing NbN/A1N/NbN and Nb/A10x/Nb tunnel junction performance with the same tuning circuit showed that the frequency dependence of the receiver noise temperature agreed well in the two receivers. These results suggest that our well-controlled NbN SIS junctions can be used for terahertz mixer elements instead of Nb SIS junctions.

•Mar 1, 1996•2 citations

A 547 GHz SIS receiver employing a submicron Nb junction with an integrated matching circuit

Pascal Febvre, William R. McGrath, P. D. Batelaan +4 more

A heterodyne receiver using an SIS (superconductor-insulator-superconductor) waveguide mixer with two mechanical tuners has been built and characterized over the frequency range of 460 GHz to 630 GHz. This receiver is designed for radioastronomy applications. The mixer uses high-current-density, 0.25- mu m/sup 2/, Nb/AlO/sub x//Nb SIS tunnel junctions with integrated superconductive RF circuits to tune the junction capacitance. A DSB (double sideband) receiver noise temperature as low as 200+or-17 K has been obtained at 540 GHz. In addition, negative differential resistance has been observed in the DC I-V (current-voltage) curve at 487-491 GHz.>

IEEE MTT-S International Microwave Symposium digest•Dec 30, 2002•4 citations

Low-noise THz Niobium SIS Mixers

Mei Bin

This thesis describes the development of low-noise heterodyne receivers at THz frequencies for submillimeter astronomy using Nb-based superconductor-insulator-superconductor (SIS) tunneling junctions. The mixers utilize a quasi-optical configuration which consists of a planar twin-slot antenna and antisymmetrically-fed two-junctions on an antireflection-coated silicon hyperhemispherical lens. On-chip integrated tuning circuits, in the form of microstrip lines, are used to obtain maximum coupling efficiency in the designed frequency band. To reduce the rf losses in the integrated tuning circuits above the superconducting Nb gap frequency (~ 700 GHz), normal-metal Al is used to replace Nb as the tuning circuits. To account the rf losses in the micros trip lines, we calculated the surface impedance of the AI films using the nonlocal anomalous skin effect for finite thickness films. Nb films were calculated using the Mattis-Bardeen theory in the extreme anomalous limit. Our calculations show that the losses of the Al and Nb microstrip lines are about equal at 830 GHz. For Al-wiring and Nb-wiring mixers both optimized at 1050 GHz, the RF coupling efficiency of Al-wiring mixer is higher than that of Nb-wiring one by almost 50%. We have designed both Nb-wiring and Al-wiring mixers below and above the gap frequency. A Fourier transform spectrometer (FTS) has been constructed especially for the study of the frequency response of SIS receivers. This FTS features large aperture size (10 inch) and high frequency resolution (114 MHz). The FTS spectra, obtained using the SIS receivers as direct detectors on the FTS, agree quite well with our theoretical simulations. We have also, for the first time, measured the FTS heterodyne response of an SIS mixer at sufficiently high resolution to resolve the LO and the sidebands. Heterodyne measurements of our SIS receivers with Nb-wiring or Al-wiring have yielded results which arc among the best reported to date for broadband heterodyne receivers. The Nb-wiring mixers, covering 400 - 850 GHz band with four separate fixed-tuned mixers, have uncorrected DSB receiver noise temperature around 5hv/kb to 700 GHz, and better than 540 K at 808 GHz. An Al-wiring mixer designed for 1050 GHz band has an uncorrected DSB receiver noise temperature 840 K at 1042 GHz and 2.5 K bath temperature. Mixer performance analysis shows that Nb junctions can work well up to twice the gap frequency and the major cause of loss above the gap frequency is the rf losses in the microstrip tuning structures. Further advances in THz SIS mixers may be possible using circuits fabricated with higher-gap superconductors such as NbN. However, this will require high-quality films with low RF surface resistance at THz frequencies.

•Jul 18, 2014•8 citations

A low noise 230 GHz heterodyne receiver employing 0.25- mu m/sup 2/ area Nb-AlO/sub x/-Nb tunnel junctions

J. Kooi, M. Chan, Tom G. Phillips +2 more

The authors report recent results for a full-height rectangular waveguide mixer with an integrated IF matching network. Two 0.25 mu m/sup 2/ Nb-AlO/sub x/-Nb superconducting-insulating-superconducting (SIS) tunnel junctions with a current density of approximately=8500 A/cm/sup 2/ and omega RC of approximately=2.5 at 230 GHz have been tested. One of these quasiparticle tunnel junctions is currently being used at the Caltech Submillimeter Observatory in Hawaii. Detailed measurement of the receiver noise have been made from 200-290 GHz for both junctions at 4.2 K. The lowest receiver noise temperatures were recorded at 239 GHz, measuring 48 K DSB at 4.2 K and 40 K DSB at 2.1 K. The 230-GHz receiver incorporates a one-octave-wide integrated low-pass filter and matching network which transforms the pumped IF junction impedance to 50 Omega over a wide range of impedances.>

IEEE Transactions on Microwave Theory and Techniques•May 1, 1992•39 citations

Design and Characterization of Two-Junction Tuning Circuits for Submillimeter SIS Mixers

Michael C. Gaidis, M. Bin, David A. B. Miller +3 more

We report on the continuing development of submillimeter quasi-optical slot antenna SIS mixers which use two-junction tuning circuits [1]. The mixers use 10 kA/cm2 Nb/Al-Oxide/Nb junctions and Nb wiring, and have generated DSB receiver noise temperatures around 5hv/kB to 700 GHz, and 16hv/kB (620 K) at 798 GHz. We present Fourier-transform spectrometer (FTS) measurements and heterodyne measurements on several such devices. In general, the measured response at frequencies below the gap of Nb is in good agreement with the predicted performance. Introduction SIS mixers with Nb-trilayer tunnel junctions offer excellent performance at frequencies below 800 GHz, and should perform competitively at frequencies as high as 1.4 THz [2-5]. Our goal is to develop a suite of ultra-low-noise SIS mixers which cover frequencies from = 400 GHz to more than I THz. At frequencies below the Nb gap (< 700 GHz), existing devices perform quite well [6], but further improvements in noise temperatures remain important. In addition, it is quite useful to be able to predict device performance given the design parameters. One can then optimize the device design for a particular frequency band, and confirm that we indeed understand the physics of the device. Progress in the design and operation of devices in this frequency range is presented below. At frequencies above the Nb gap, RF photons can break Cooper pairs, resulting in greater signal loss and higher receiver noise temperatures. The loss is particularly important in the slender microstrip lines used to resonate the junction capacitance and to transform the antenna impedance down to the RF junction impedance. However, the actual coupling of radiation into Nb junctions above the gap should still be reasonably efficient -more than 30% at 800 GHz [7]. In addition to RF loss, one is also affected by increased dispersion at frequencies near the gap. The Nb microstriplines have therefore been carefully designed to ensure the desired bandpass is achieved. We demonstrate for the first time that all-Nb SIS receivers can have substantially better performance than GaAs Schottky receivers for the astronomically important CI ( P2 — P 1 ) and CO (7-6) transitions near 810 GHz. Receiver Configuration Since waveguide mixers become difficult to construct at short submillimeter wavelengths, we have adopted a quasi-optical approach. Here, lenses take the place of waveguide horns, and the incoming radiation is collected by a planar antenna on the SIS mixer substrate [8]. This offers several other advantages, such as on-chip broad-band silt a SS 114 SSE WA Wa Sta MX Dewar 120 Mylar Window SIS Mixer 295 IQ 77 K Mylar Load Bearnsplitter ICI 1= NZ IC =1 HEN1T Amplifier Polyethylene Lens

•Mar 1, 1995•2 citations
We report recent results on a 580-740 GHz SIS heterodyne receiver employing a tuned 0.50Am Nb/A10x/Nb SIS tunnel junction. The receiver has been successfully installed at the Caltech Submillimeter Observatory, Hawaii. Results of an untuned device in the same waveguide block were presented at the fifth International THz Conference. Since the mixer is meant to be operated near the superconducting gap frequency of niobium (2,L/h 690 GHz), special has been taken to minimize the absorption loss in the rf matching network. To this effect we propose the use of a RF matching network that constitutes a hybrid between the well know end-loaded stub and radial stub matching networks. We have measured uncorrected DSB receiver temperatures as low as 160K from 680to 702 Gliz, 200K at 725GHz and 120K from 585-640 GHz. The uncorrected mixer noise temperature at 702 Gliz is about 125K, of which 62K can be directly contributed to the front end optics loss. Mixer conversion loss at 702 GHz is 7dB, of which 0.9dB is due to the absorption loss in the Nb film. This results in a corrected mixer noise temperature of 63K, 1.7 times the quantum noise limit.
We report on a 850-GHz superconducting-insulator-superconducting (SIS) heterodyne receiver employing an RF-tuned niobium tunnel junction with a current density of 14 kA/cm^2, fabricated on a 1-µm Si_3N_4 supporting membrane. Since the mixer is designed to be operated well above the superconducting gap frequency of niobium (2Δ/h ≈ 690 GHz), special care has been taken to minimize niobium transmission-line losses. Both Fourier transform spectrometer (FTS) measurements of the direct detection performance and calculations of the IF output noise with the mixer operating in heterodyne mode, indicate an absorption loss in the niobium film of about 6.8 dB at 822 GHz. These results are in reasonably good agreement with the loss predicted by the Mattis-Bardeen theory in the extreme anomalous limit. From 800 to 830 GHz, we report uncorrected receiver noise temperatures of 518 or 514 K when we use Callen and Welton's law to calculate the input load temperatures. Over the same frequency range, the mixer has a 4-dB conversion loss and 265 K ± 10 K noise temperature. At 890 GHz, the sensitivity of the receiver has degraded to 900 K, which is primarily the result of increased niobium film loss in the RF matching network. When the mixer was cooled from 4.2 to 1.9 K, the receiver noise temperature improved about 20% 409-K double sideband (DSB). Approximately half of the receiver noise temperature improvement can be attributed to a lower mixer conversion loss, while the remainder is due to a reduction in the niobium film absorption loss. At 982 GHz, we measured a receiver noise temperature of 1916 K.
We report on low-noise heterodyne mixing with NbN/A1N/NbN tunnel junctions in the submillimeter-wave region for the first time. The receiver consists of the quasi-optical NbN SIS mixer with an integrated tuning circuit in which a radial short stub tuner is incorporated to resonate out the junction capacitance for RF matching and a balanced IF circuit for broadband IF matching. The prepared NbN SIS junction has a current density of 20 kA/cm 2 and is about 1 I1111 in diameter, supplying a small coC JRN product (o)CJRN = 3 at 300 GHz). The junctions showed good dc I-V characteristics, excellent submillimeter-wave responses and sensitive heterodyne mixing responses. From 254 to 350 GHz the average receiver noise temperature measured using by the standard Y-factor method was about 250 K (DSB) at 5 K. The lowest receiver noise temperature, 200 K (DSB), was obtained at around 303 GHz. Comparing NbN/A1N/NbN and Nb/A10x/Nb tunnel junction performance with the same tuning circuit showed that the frequency dependence of the receiver noise temperature agreed well in the two receivers. These results suggest that our well-controlled NbN SIS junctions can be used for terahertz mixer elements instead of Nb SIS junctions.
A heterodyne receiver using an SIS (superconductor-insulator-superconductor) waveguide mixer with two mechanical tuners has been built and characterized over the frequency range of 460 GHz to 630 GHz. This receiver is designed for radioastronomy applications. The mixer uses high-current-density, 0.25- mu m/sup 2/, Nb/AlO/sub x//Nb SIS tunnel junctions with integrated superconductive RF circuits to tune the junction capacitance. A DSB (double sideband) receiver noise temperature as low as 200+or-17 K has been obtained at 540 GHz. In addition, negative differential resistance has been observed in the DC I-V (current-voltage) curve at 487-491 GHz.>
This thesis describes the development of low-noise heterodyne receivers at THz frequencies for submillimeter astronomy using Nb-based superconductor-insulator-superconductor (SIS) tunneling junctions. The mixers utilize a quasi-optical configuration which consists of a planar twin-slot antenna and antisymmetrically-fed two-junctions on an antireflection-coated silicon hyperhemispherical lens. On-chip integrated tuning circuits, in the form of microstrip lines, are used to obtain maximum coupling efficiency in the designed frequency band. To reduce the rf losses in the integrated tuning circuits above the superconducting Nb gap frequency (~ 700 GHz), normal-metal Al is used to replace Nb as the tuning circuits. To account the rf losses in the micros trip lines, we calculated the surface impedance of the AI films using the nonlocal anomalous skin effect for finite thickness films. Nb films were calculated using the Mattis-Bardeen theory in the extreme anomalous limit. Our calculations show that the losses of the Al and Nb microstrip lines are about equal at 830 GHz. For Al-wiring and Nb-wiring mixers both optimized at 1050 GHz, the RF coupling efficiency of Al-wiring mixer is higher than that of Nb-wiring one by almost 50%. We have designed both Nb-wiring and Al-wiring mixers below and above the gap frequency. A Fourier transform spectrometer (FTS) has been constructed especially for the study of the frequency response of SIS receivers. This FTS features large aperture size (10 inch) and high frequency resolution (114 MHz). The FTS spectra, obtained using the SIS receivers as direct detectors on the FTS, agree quite well with our theoretical simulations. We have also, for the first time, measured the FTS heterodyne response of an SIS mixer at sufficiently high resolution to resolve the LO and the sidebands. Heterodyne measurements of our SIS receivers with Nb-wiring or Al-wiring have yielded results which arc among the best reported to date for broadband heterodyne receivers. The Nb-wiring mixers, covering 400 - 850 GHz band with four separate fixed-tuned mixers, have uncorrected DSB receiver noise temperature around 5hv/kb to 700 GHz, and better than 540 K at 808 GHz. An Al-wiring mixer designed for 1050 GHz band has an uncorrected DSB receiver noise temperature 840 K at 1042 GHz and 2.5 K bath temperature. Mixer performance analysis shows that Nb junctions can work well up to twice the gap frequency and the major cause of loss above the gap frequency is the rf losses in the microstrip tuning structures. Further advances in THz SIS mixers may be possible using circuits fabricated with higher-gap superconductors such as NbN. However, this will require high-quality films with low RF surface resistance at THz frequencies.
The authors report recent results for a full-height rectangular waveguide mixer with an integrated IF matching network. Two 0.25 mu m/sup 2/ Nb-AlO/sub x/-Nb superconducting-insulating-superconducting (SIS) tunnel junctions with a current density of approximately=8500 A/cm/sup 2/ and omega RC of approximately=2.5 at 230 GHz have been tested. One of these quasiparticle tunnel junctions is currently being used at the Caltech Submillimeter Observatory in Hawaii. Detailed measurement of the receiver noise have been made from 200-290 GHz for both junctions at 4.2 K. The lowest receiver noise temperatures were recorded at 239 GHz, measuring 48 K DSB at 4.2 K and 40 K DSB at 2.1 K. The 230-GHz receiver incorporates a one-octave-wide integrated low-pass filter and matching network which transforms the pumped IF junction impedance to 50 Omega over a wide range of impedances.>
We report on the continuing development of submillimeter quasi-optical slot antenna SIS mixers which use two-junction tuning circuits [1]. The mixers use 10 kA/cm2 Nb/Al-Oxide/Nb junctions and Nb wiring, and have generated DSB receiver noise temperatures around 5hv/kB to 700 GHz, and 16hv/kB (620 K) at 798 GHz. We present Fourier-transform spectrometer (FTS) measurements and heterodyne measurements on several such devices. In general, the measured response at frequencies below the gap of Nb is in good agreement with the predicted performance. Introduction SIS mixers with Nb-trilayer tunnel junctions offer excellent performance at frequencies below 800 GHz, and should perform competitively at frequencies as high as 1.4 THz [2-5]. Our goal is to develop a suite of ultra-low-noise SIS mixers which cover frequencies from = 400 GHz to more than I THz. At frequencies below the Nb gap (< 700 GHz), existing devices perform quite well [6], but further improvements in noise temperatures remain important. In addition, it is quite useful to be able to predict device performance given the design parameters. One can then optimize the device design for a particular frequency band, and confirm that we indeed understand the physics of the device. Progress in the design and operation of devices in this frequency range is presented below. At frequencies above the Nb gap, RF photons can break Cooper pairs, resulting in greater signal loss and higher receiver noise temperatures. The loss is particularly important in the slender microstrip lines used to resonate the junction capacitance and to transform the antenna impedance down to the RF junction impedance. However, the actual coupling of radiation into Nb junctions above the gap should still be reasonably efficient -more than 30% at 800 GHz [7]. In addition to RF loss, one is also affected by increased dispersion at frequencies near the gap. The Nb microstriplines have therefore been carefully designed to ensure the desired bandpass is achieved. We demonstrate for the first time that all-Nb SIS receivers can have substantially better performance than GaAs Schottky receivers for the astronomically important CI ( P2 — P 1 ) and CO (7-6) transitions near 810 GHz. Receiver Configuration Since waveguide mixers become difficult to construct at short submillimeter wavelengths, we have adopted a quasi-optical approach. Here, lenses take the place of waveguide horns, and the incoming radiation is collected by a planar antenna on the SIS mixer substrate [8]. This offers several other advantages, such as on-chip broad-band silt a SS 114 SSE WA Wa Sta MX Dewar 120 Mylar Window SIS Mixer 295 IQ 77 K Mylar Load Bearnsplitter ICI 1= NZ IC =1 HEN1T Amplifier Polyethylene Lens