The authors report on the high-speed operation of a superconducting comparator circuit, based on coupling the quantum flux parametron (QFP) to an RF SQUID, which can be used to build a flash-type analog-to-digital converter (ADC). Simulations of this circuit show that it is expected to achieve operation with input signal bandwidths greater than 4 GHz and with a dynamic range equal to at least 4 b of resolution. A QFP-based comparator fabricated with a process using NbN/Pb-alloy Josephson junctions of 5 mu m by 5 mu m and a current density of 100 A/cm/sup 2/ has been examined to evaluate the properties of the QFP-ADC. Analog-to-digital conversion of the comparator has been observed with a QFP activation frequency up to 18.2 GHz. By employing a sampling method, input signals with frequencies up to 5.4 GHz have also been digitized.>
The authors report on the high-speed operation of a superconducting comparator circuit, based on coupling the quantum flux parametron (QFP) to an RF SQUID, which can be used to build a flash-type analog-to-digital converter (ADC). Simulations of this circuit show that it is expected to achieve operation with input signal bandwidths greater than 4 GHz and with a dynamic range equal to at least 4 b of resolution. A QFP-based comparator fabricated with a process using NbN/Pb-alloy Josephson junctions of 5 mu m by 5 mu m and a current density of 100 A/cm/sup 2/ has been examined to evaluate the properties of the QFP-ADC. Analog-to-digital conversion of the comparator has been observed with a QFP activation frequency up to 18.2 GHz. By employing a sampling method, input signals with frequencies up to 5.4 GHz have also been digitized.>
A flash-type superconducting A/D (analog/digital) converter is proposed. The basis low-frequency operation of this converter, which compromises a quantum flux parametron (QFP) and an RF SQUID (superconducting quantum interference device), has been observed. The RF SQUID consists of a Josephson junction and a load inductor which is part of the QFP. It converts an analog signal to period digital signals of one quantum flux (2.07*10/sup -5/ W-b) per cycle. The QFP works as both an amplifier and a comparator of the periodic digital signals, by adding an exciting signal. This A/D converter is expected to achieve high-speed operation of 20 GHz. Several 4-bit A/D converter circuits were fabricated, using the conventional Nb-Pb alloy process, with a junction size of 5 mu m*5 mu m and supercurrent density of 200 A/cm/sup 2/. Basic operation at 100 KHz was confirmed experimentally.>
We compare the SQUID wheel/Quantum Flux Parametron (QFP) comparator to a new Rapid Single Flux Quantum (RSFQ) compatible design. Both have been simulated to demonstrate /spl sim/0.5 ps threshold accuracy which would permit the construction of a flash analog-to-digital converter with six effective bits of resolution at 10 GHz input bandwidth, over three times better than the best performance demonstrated with any technology, At lower input frequencies, both designs have demonstrated that a 10-bit flash ADC is possible. Although simulations of the QFP-based design are more accurate at high signal slew rates due to its symmetry, the RSFQ-based design has a better signal-to-noise ratio and a faster and more flexible clocking scheme which ultimately prove to be more important.
We have designed a fully integrated 5-bit flash-type single-flux quantum (SFQ) analog-to-digital converter (ADC), in which an error correction and a bit-interleaving circuit are integrated with complementary quasi-one-junction SQUID (CQOS) comparators, and we verified its operation in experiments. Two types of look-back error correction circuits with different clock schemes were designed for the integrated ADCs to avoid the gray zone in comparators and to convert gray code to binary code. The interleaving circuit was also used in the ADC to add one extra bit. A binary 5-bit A/D converter was integrated into an IC chip. Then, input waveforms at low frequencies were successfully retrieved from the binary data of the A/D converter without any errors. We also confirmed that the A/D converter operated properly by conducting tests in our cryocooling system using a 4K-GM cryocooler after the chip was flip-chip bonded onto a multi-chip-module (MCM) carrier. We also used the beat frequency method to test and confirm that the CQOS comparator operated effectively at high frequency, i.e., 3 bits at 15 GHz in the binary code operation and 4 bits at 15 GHz in the gray code operation. Furthermore, operations at sampling frequencies of up to 32 and 50 GHz with a low-frequency analog input signal were experimentally confirmed for a 4-bit comparator circuit with a critical current density Jcof 2.5 kA/cm2and 10 kA/cm2, respectively.
This paper presents the progress we have made on our design, fabrication, and testing of a fully parallel superconducting analog-to-digital converter (ADC) with multi-GHz clock frequencies and input bandwidth. To our best knowledge, this converter is the first flash-type analog-to-digital converter ever reported in Josephson technology that fully integrates a quantizer and a thermometer-to-binary encoder to achieve binary outputs. In this design, the quantizer consists of 2(superscript N-1 comparators, each of which is realized using a hysteretic one- junction sampling SQUID driving a two-junction readout SQUID. A new logic family has been designed based on the same comparator building block and has been used to implement the thermometer-to- binary encoder. Taking advantage of the fact that the encoder's input is thermometer-coded, we have designed three-input and four-input quasi-XOR gates with only three NAND gates and therefore reduced significantly the total gate count. Functionalities of all the sub-circuits have been verified experimentally at clock frequencies up to 3 GHz, which is limited by our currently available testing equipment.
Successful utilization of the quasi one-junction SQUID (QOS) as a signal comparator for analog-to-digital conversion (ADC) has been demonstrated by several groups, This idea is extended to show how similar comparators can be integrated into an all rapid single flux quantum (RSFQ) digital architecture. Comparators are interrogated by SFQ sampling pulses and in turn give output according to the RSFQ convention. One- and two-bit ADC's have been simulated, fabricated and tested at low speed. Total performance of these devices is estimated within the framework of a multiple bit parallel flash ADC architecture.>
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).